Search Results (7.2K)
Conversation Type :
Posts
Published Date :
Lifetime
Category
Community Accepted Solution
Hi All, I have Dell PowerEdge R740 with RAID5 array built of 8 disks. I need to erase all data with no recovery possibility. Would Standard Disks (Overwrite Data) work for me? Also, why Cryptographic Erase Disks option is greyed out? Thanks in advance.
Question
•
PowerEdge Hardware General
Community Accepted Solution
I have an R740 LFF with riser configuration 1B+2A+3A. I want to install a GPU that won't cause the fan minimum to increase due to being a third party PCIe card. Without the cards I've tried, fan minimum is 7% PWM. With the GPU installed the minimum is 29%. Inlet air temp is the same and PCI airflow
Question
•
PowerEdge Hardware General
Official Solution
Hi all, Apologies for this boring question, A12 rack rails have been added to a server before getting it to the rack!! I need to undo the lot as the server might just sit on a shelf instead. Not sure how to do that if someone has any handy hints or a video please?
Question
•
Rack Servers
Community Accepted Solution
Official Solution
We are currently working through our network and found several severs that contain DSET Version 3.7.0. Does Dell provide the java license or will we need to remove this software?
Question
•
Systems Management General
Official Solution
Is there a way to fun a firmware update just on the iDrac firmware on all my servers at once?
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
Hello I'm using ipmitool to measure server power. # ipmitool -I lanplus -H xxx.xxx.xxx.xxx -U root -P xxx dcmi power reading Instantaneous power reading: 129 Watts Minimum during sampling period: 15 Watts Maximum during sampling period: 292 Watts Average power reading over sample pe
Question
•
PowerEdge Hardware General
Official Solution
I am writing to you regarding an issue I have been experiencing with my Dell PowerEdge T420 server. I recently replaced the CMOS battery, but I am receiving conflicting error messages.Immediately after the replacement, I received an error message stating "The CMOS battery has failed". However, short
Question
•
PowerEdge Hardware General
Official Solution
So, I was given a task by my employer to recover data from a set of old servers he had acquired. The servers in question are two T440 tower servers and one R340 (as far as I could tell from the labeling). I have been able to boot up one of the towers and gain access via a boot drive. However, the o
Question
•
PowerEdge HDD/SCSI/RAID
Official Solution
Hi, I need to change the processor to become a base Frequency of 2.9 MHz can I do that for PowerEdge R730 - Intel Xeon E5-2680 V4.
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hello! I just got new PowerEdge T160 server. 2 HDDs installed as RAID 1. I wanted to add additional HDD. However, I need plastic HDD carrier (caddy?) to hold HDD inside of PC. It's blue color, plastic, mount on side of HDD. There is tag (see attached photo). But I can't find any info about it. I nee
Question
•
PowerEdge HDD/SCSI/RAID
Community Accepted Solution
We have a Dell server under warranty with service tag: <Private data removed from public view. DELL-Admin>.We have sold to them the server, the first configuration when they bought the server was with 1 CPU ( AMD EPYC 7313). They want to update the server with a second cpu, with th
Question
•
Rack Servers
Community Accepted Solution
Hello everyone, I'm assuming that I'm not doing something quite right or that I'm overlooking something. I have rolled out new local iDRAC users on a server using a template. I have created the template from a reference system The message after the job is done looks like this: #### SummaryAct
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
Hello all, we have S4820T switches that we want to configure SNMP on it. When we try to configure the SNMP after going to config mode we are getting error: Error: Invalid input at "^" marker. sw01(conf)#snmp? ^% E
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
I have inherited an R730 unit at one of my customers that is running medical imaging software on it. The secondary drive is a RAID10 array of 6x Intel SSDC2KB48 480gb SSDs in a PERC H730 Mini (embedded) for a combined total of 1.34TB. It's almost full. I'd like to rebuild that array from raid10 to r
Question
•
PowerEdge HDD/SCSI/RAID
Community Accepted Solution
Official Solution
Hi all, Is it possible to convert a single disk to a RAID 1 on R250 server with S150 controller? This server will be delivered to us next week with only one disk and the second disk will be delivered next month so I don't want to wait to install server. So I would like to start with one disk and af
Question
•
PowerEdge HDD/SCSI/RAID
Community Accepted Solution
hi I need to find Dell PowerEdg R940 (IDRAC 9) MIB files. Please help me
Question
•
Systems Management General
Community Accepted Solution
Hi all I’ve recently changed my servers motherboard however the board is in a different chassis to the original is there any way to transfer the physical service tag on the chassis (one on the little sliding out bit of plastic) to the new chassis so it matches the motherboard
Question
•
PowerEdge Hardware General
Community Accepted Solution
Is there anything from Dell about compatibility between the OMEVV plugin and the new vSphere 8.0.3 update? It's been out for a month now, but the OMEVV web page still shows compatibility with Update 2.
Question
•
OpenManage Integration for VMware vCenter
Official Solution
Hi folks, We have some issues with SAN storage causing kernel CPU locks/kernel crashes on a pair of Dell R740 servers (Oracle RAC), does this sound like a hardware issue related to perhaps a BIOS issue, would a later BIOS resolve these potentially? Oracle are suggesting it may be. I can provide a
Question
•
PowerEdge Hardware General
Community Accepted Solution
I have a ticket number for a specific case & would like to know its status
Question
•
Dell OpenManage Enterprise