Search

Hello, I'm trying to reset the ACL SMB share following this command: svc_cifssupport SMB-SHARE-NAME -acl -fs FileSystem-NAME -reset -path \SHARE-FOLDER but no luck, I'm receiving errors Command failed Error 4020: SMB-SHARE-NAME : failed to complete command any ideas? thanks,

Hi All, I have Dell PowerEdge R740 with RAID5 array built of 8 disks. I need to erase all data with no recovery possibility. Would Standard Disks (Overwrite Data) work for me? Also, why Cryptographic Erase Disks option is greyed out? Thanks in advance.

I have an R740 LFF with riser configuration 1B+2A+3A. I want to install a GPU that won't cause the fan minimum to increase due to being a third party PCIe card. Without the cards I've tried, fan minimum is 7% PWM. With the GPU installed the minimum is 29%. Inlet air temp is the same and PCI airflow

Hi all, Apologies for this boring question, A12 rack rails have been added to a server before getting it to the rack!! I need to undo the lot as the server might just sit on a shelf instead. Not sure how to do that if someone has any handy hints or a video please?

We are currently working through our network and found several severs that contain DSET Version 3.7.0. Does Dell provide the java license or will we need to remove this software?

Is there a way to fun a firmware update just on the iDrac firmware on all my servers at once?

Hello I'm using ipmitool to measure server power. # ipmitool -I lanplus -H xxx.xxx.xxx.xxx -U root -P xxx dcmi power reading Instantaneous power reading: 129 Watts Minimum during sampling period: 15 Watts Maximum during sampling period: 292 Watts Average power reading over sample pe

Hi All, I have a md3460 that is in a controller lockdown state, i have attempted to reset the password. Service Interface Main Menu==============================   1)Display IP Configuration  2)Change IP Configuration  3)Reset Storage Array Administrator Password  4)Display 7-

I am writing to you regarding an issue I have been experiencing with my Dell PowerEdge T420 server. I recently replaced the CMOS battery, but I am receiving conflicting error messages.Immediately after the replacement, I received an error message stating "The CMOS battery has failed". However, short

So, I was given a task by my employer to recover data from a set of old servers he had acquired. The servers in question are two T440 tower servers and one R340 (as far as I could tell from the labeling). I have been able to boot up one of the towers and gain access via a boot drive. However, the o

Hi, I need to change the processor to become a base Frequency of 2.9 MHz can I do that for  PowerEdge R730 - Intel Xeon E5-2680 V4.

Hello! I just got new PowerEdge T160 server. 2 HDDs installed as RAID 1. I wanted to add additional HDD. However, I need plastic HDD carrier (caddy?) to hold HDD inside of PC. It's blue color, plastic, mount on side of HDD. There is tag (see attached photo). But I can't find any info about it. I nee

Hello All. Hitachi is not showing capacity values. Other things it shows in reports. But no value for capacity. Also, when volumes are checked in reports, it shows all the ldevs/volumes fine, but nothing for capacity and used capacity. Collector Logs has no errors, nothing to look for. All good and

We have a Dell server under warranty with service tag: <Private data removed from public view. DELL-Admin>.We have sold to them the server, the first configuration when they bought the server was with 1 CPU ( AMD EPYC 7313).  They want to update the server with a second cpu, with th

Hello everyone, I'm assuming that I'm not doing something quite right or that I'm overlooking something. I have rolled out new local iDRAC users on a server using a template. I have created the template from a reference system The message after the job is done looks like this:  #### SummaryAct

Hello all, we have S4820T switches that we want to configure SNMP on it. When we try to configure the SNMP after going to config mode we are getting error: Error: Invalid input at "^" marker. sw01(conf)#snmp?                        ^% E

I have inherited an R730 unit at one of my customers that is running medical imaging software on it. The secondary drive is a RAID10 array of 6x Intel SSDC2KB48 480gb SSDs in a PERC H730 Mini (embedded) for a combined total of 1.34TB. It's almost full. I'd like to rebuild that array from raid10 to r

Hello Everyone,Switch Model: N2000PFirmware: 6.6.3.17 I am trying to configure dot1x authentication using the Cloud Radius server. The configuration I am applying is as below but the switch is not even sending request to the radius(Public IP).Configuration: 1. Enter global configuration mode and de

Hi We have 2 N3248TE-ON switches that we want to stack for redundancy. We understand that with OS10 there is no more stacking between switches and VLT is now used.  I have been though instructions to setup VLT for OS10 We want to use the 100Gb DAC interface to connect the switches rather th

Hi all, Is it possible to convert a single disk to a RAID 1 on R250 server with S150 controller? This server will be delivered to us next week with only one disk and the second disk will be delivered next month so I don't want to wait to install server. So I would like to start with one disk and af