Symptoms
設定新的次要網路 (例如複寫網路) 的客戶注意到其介面也可用於 ISCSI 儲存。
移除/刪除該網路的功能會呈現灰色,因此無法執行。
Cause
所有儲存裝置相關 IP 通訊協定的使用均依儲存裝置網路資源的設計。
其用途無法在目前的 Powerstore 實作中分隔。
Resolution
這屬於「設計」問題,並已記錄在複寫指南中:
使用預設組態進行複寫規劃時,請考慮連接埠也用於其他流量,例如 iSCSI 主機存取、遷移和檔案的 I/O (僅限 PowerStore T 機型)。如果使用這些功能,建議您使用專用介面來規劃複寫。額外的連接埠會使用從 ICW 中指定或在 PowerStore Manager 的網路區段中加入的範圍動態儲存 IP 組態。
Dell EMC PowerStore:複製技術 (delltechnologies.com)
適用於 PowerStore T 機型的 Dell EMC PowerStore 網路指南
如果強制刪除次要網路時需要進一步協助,請聯絡 Dell 支援並引用此知識文章。
請注意,pstcli 也不會提供移除網路的任何明確可能性,因為其已標示為在使用中。
Additional Information
Powerstore CLI (PSTCLI) 作業:
cli> network -id NW7 show
id = NW7
type = Storage
name = Replication
ip_version = IPv4
purposes = ISCSI
vlan_id = 40
prefix_length = 24
gateway =
mtu = 9000
reusable_id = 2
type_l10n = Storage
ip_version_l10n = IPv4
purposes_l10n = iSCSI
ip_pool_addresses:
id = IP24
name = Replication (1xx.1xx.40.xxx)
network_id = NW7
ip_port_id = IP_PORT2
appliance_id = A1
node_id = N1
address = 1xx.1xx.40.xxx
purposes = Storage_Iscsi_Target, External_Replication_Iscsi
purposes_l10n = Storage Iscsi Target, External Replication iSCSI Port
id = IP25
name = Replication (1xx.1xx.40.xxx)
network_id = NW7
ip_port_id = IP_PORT6
appliance_id = A1
node_id = N2
address = 1xx.1xx.40.xxx
purposes = Storage_Iscsi_Target, External_Replication_Iscsi
purposes_l10n = Storage Iscsi Target, External Replication iSCSI Port
cli> network -id NW7 delete
作業失敗
messages:
code = 0xE0E200702003
severity = Error
message_l10n = 無法刪除網路「複寫」,因為其已對應至 IP 連接埠:IP_PORT2, IP_PORT6。請先取消對應網路中的所有連接埠,再將其刪除。
arguments = Replication, IP_PORT2, IP_PORT6
cli> network -id NW7 -remove_port_ids IP24
在「-remove_port_ids」權杖附近命令列剖析失敗。
語法錯誤。
cli> network -id NW7 scale -remove_port_ids IP_PORT2
無效的要求
messages:
code = 0xE0E250701005
severity = Error
message_l10n = 儲存裝置網路無法從使用中移除 IP 連接埠 IP_PORT2,因為其用於外部複寫。
arguments = IP_PORT2
cli> network -id NW7 scale -remove_port_ids IP_PORT6
無效的要求
messages:
code = 0xE0E250701005
severity = Error
message_l10n = 儲存裝置網路無法從使用中移除 IP 連接埠 IP_PORT2,因為其用於外部複寫。
arguments = IP_PORT2
cli>
cli> ip_port -id IP_PORT2 set -remove_current_usages ISCSI
在「-remove_current_usages」權杖附近命令列剖析失敗。 ===> pstcli 中不存在此類選項
語法錯誤。
cli> ip_port -id IP_PORT2 set -add_current_usages ISCSI
無效的要求
messages:
code = 0xE0E600701002
severity = Error
message_l10n = The IP 連接埠 IP_PORT2 不支援新增下列用法:ISCSI。
arguments = IP_PORT2, ISCSI
cli> ip_port -id IP_PORT2 set -add_current_usages External_Replication
無效的要求
messages:
code = 0xE0E200702005
severity = Error
message_l10n = External_Replication 可使用多個網路進行。必須明確指定目標網路識別碼。
arguments = External_Replication