Symptoms
Çoğaltma ağı gibi yeni bir ikincil ağ yapılandıran bir müşteri, ağın arayüzlerinin ISCSI depolaması için de kullanılabilir olduğunu fark eder.
Bu ağı kaldırma veya silme seçeneği devre dışı olduğundan bu işlemleri yapmak mümkün değildir.
Cause
Tasarım gereği, depolama ağı kaynakları depolamayla ilgili tüm IP protokolleri tarafından kullanılır.
Kullanım amaçları mevcut Powerstore uygulamasında ayrılamaz.
Resolution
Bu sorun "tasarım gereği çalışma" olarak kabul edilir ve Çoğaltma Kılavuzu'nda belgelenmiştir:
Varsayılan yapılandırmayı kullanarak çoğaltmayı planlarken, bağlantı noktalarının iSCSI ana bilgisayar erişimi, taşıma ve dosya G/Ç'si (yalnızca PowerStore T modelleri) gibi diğer trafikler için de kullanıldığından emin olun. Bu özellikler kullanılıyorsa özel arayüzlerden yararlanarak çoğaltmayı planlamanız önerilir. Ek bağlantı noktaları, ICW'de sağlanan veya PowerStore Manager'ın networking (ağ) bölümüne eklenen aralıkta dinamik depolama IP yapılandırmasını kullanır.
Dell EMC PowerStore: Çoğaltma Teknolojileri (delltechnologies.com) (İngilizce)
PowerStore T Modelleri İçin Dell EMC PowerStore Ağ Kılavuzu (İngilizce)
İkincil ağı zorla silme konusunda daha fazla yardıma ihtiyaç duyarsanız lütfen Dell Destek ekibiyle iletişim kurun ve bu Knowledge Base makalesini referans gösterin.
Ağ kullanımda olarak işaretlendiğinden, pstcli uygulamasının da ağı kaldırma imkanı sunmayacağını lütfen unutmayın.
Additional Information
Powerstore CLI (PSTCLI) işlemleri:
cli> network -id NW7 show
id = NW7
type = Storage
name = Replication
ip_version = IPv4
purposes = ISCSI
vlan_id = 40
prefix_length = 24
gateway =
mtu = 9000
reusable_id = 2
type_l10n = Storage
ip_version_l10n = IPv4
purposes_l10n = iSCSI
ip_pool_addresses:
id = IP24
name = Replication (1xx.1xx.40.xxx)
network_id = NW7
ip_port_id = IP_PORT2
appliance_id = A1
node_id = N1
address = 1xx.1xx.40.xxx
purposes = Storage_Iscsi_Target, External_Replication_Iscsi
purposes_l10n = Storage Iscsi Target, External Replication iSCSI Port
id = IP25
name = Replication (1xx.1xx.40.xxx)
network_id = NW7
ip_port_id = IP_PORT6
appliance_id = A1
node_id = N2
address = 1xx.1xx.40.xxx
purposes = Storage_Iscsi_Target, External_Replication_Iscsi
purposes_l10n = Storage Iscsi Target, External Replication iSCSI Port
cli> network -id NW7 delete
Operation Failed
messages:
code = 0xE0E200702003
severity = Error
message_l10n = Network 'Replication' could not be deleted since it is mapped to IP ports: IP_PORT2, IP_PORT6. Unmap all ports from the network before deleting it.
arguments = Replication, IP_PORT2, IP_PORT6
cli> network -id NW7 -remove_port_ids IP24
Command line parsing failed near "-remove_port_ids" token.
Syntax error.
cli> network -id NW7 scale -remove_port_ids IP_PORT2
Invalid Request
messages:
code = 0xE0E250701005
severity = Error
message_l10n = The IP port IP_PORT2 cannot be removed from the use by Storage network because it is used for External Replication.
arguments = IP_PORT2
cli> network -id NW7 scale -remove_port_ids IP_PORT6
Invalid Request
messages:
code = 0xE0E250701005
severity = Error
message_l10n = The IP port IP_PORT2 cannot be removed from the use by Storage network because it is used for External Replication.
arguments = IP_PORT2
cli>
cli> ip_port -id IP_PORT2 set -remove_current_usages ISCSI
Command line parsing failed near "-remove_current_usages" token. ===> no such option exist in pstcli
Syntax error.
cli> ip_port -id IP_PORT2 set -add_current_usages ISCSI
Invalid Request
messages:
code = 0xE0E600701002
severity = Error
message_l10n = The IP port IP_PORT2 does not support the addition of the following usages: ISCSI.
arguments = IP_PORT2, ISCSI
cli> ip_port -id IP_PORT2 set -add_current_usages External_Replication
Invalid Request
messages:
code = 0xE0E200702005
severity = Error
message_l10n = Multiple networks can be used for External_Replication. The target network identifier must be explicitly specified.
arguments = External_Replication