Symptoms
복제 네트워크와 같은 새 보조 네트워크를 구성한 고객이 해당 인터페이스를 iSCSI 스토리지에도 사용할 수 있음을 알게 되었습니다.
네트워크 제거/삭제가 회색으로 표시되어 사용할 수 없습니다.
Cause
스토리지 네트워크 리소스는 설계에 따라 모든 스토리지 관련 IP 프로토콜에서 사용됩니다.
현재 Powerstore 구축에서는 용도를 분리할 수 없습니다.
Resolution
이 문제는 '설계'에 따라 고려되며 복제 가이드에 설명되어 있습니다.
기본 구성을 사용하여 복제를 계획할 때는 iSCSI 호스트 액세스, 마이그레이션 및 파일(PowerStore T 모델만 해당)을 위한 I/O와 같은 다른 트래픽에도 포트가 사용된다는 점을 고려하십시오. 이러한 기능을 사용하는 경우 전용 인터페이스를 사용하여 복제를 계획하는 것이 좋습니다. 추가 포트는 ICW에서 제공하거나 PowerStore Manager의 네트워킹 섹션에 추가된 범위의 동적 스토리지 IP 구성을 사용합니다.
Dell EMC PowerStore: 복제 기술(delltechnologies.com)
PowerStore T 모델용 Dell EMC PowerStore 네트워킹 가이드
보조 네트워크를 강제로 삭제하는 데 추가 지원이 필요한 경우 Dell 지원 부서에 문의하여 이 기술 자료 문서를 인용하십시오.
또한 pstcli는 사용 중인 것으로 표시되므로 네트워크를 제거할 수 있는 명확한 가능성을 제공하지 않습니다.
Additional Information
PSTCLI(Powerstore CLI) 작업:
cli> network -id NW7 show
id = NW7
type = Storage
name = Replication
ip_version = IPv4
purposes = ISCSI
vlan_id = 40
prefix_length = 24
gateway =
mtu = 9000
reusable_id = 2
type_l10n = Storage
ip_version_l10n = IPv4
purposes_l10n = iSCSI
ip_pool_addresses:
id = IP24
name = Replication (1xx.1xx.40.xxx)
network_id = NW7
ip_port_id = IP_PORT2
appliance_id = A1
node_id = N1
address = 1xx.1xx.40.xxx
purposes = Storage_Iscsi_Target, External_Replication_Iscsi
purposes_l10n = Storage Iscsi Target, External Replication iSCSI Port
id = IP25
name = Replication (1xx.1xx.40.xxx)
network_id = NW7
ip_port_id = IP_PORT6
appliance_id = A1
node_id = N2
address = 1xx.1xx.40.xxx
purposes = Storage_Iscsi_Target, External_Replication_Iscsi
purposes_l10n = Storage Iscsi Target, External Replication iSCSI Port
cli> network -id NW7 delete
Operation Failed
메시지:
code = 0xE0E200702003
severity = Error
message_l10n = Network 'Replication' could not be deleted since it is mapped to IP ports: IP_PORT2, IP_PORT6. Unmap all ports from the network before deleting it.
arguments = Replication, IP_PORT2, IP_PORT6
cli> network -id NW7 -remove_port_ids IP24
Command line parsing failed near "-remove_port_ids" token.
Syntax error.
cli> network -id NW7 scale -remove_port_ids IP_PORT2
Invalid Request
messages:
code = 0xE0E250701005
severity = Error
message_l10n = The IP port IP_PORT2 cannot be removed from the use by Storage network because it is used for External Replication.
arguments = IP_PORT2
cli> network -id NW7 scale -remove_port_ids IP_PORT6
Invalid Request
messages:
code = 0xE0E250701005
severity = Error
message_l10n = The IP port IP_PORT2 cannot be removed from the use by Storage network because it is used for External Replication.
arguments = IP_PORT2
cli>
cli> ip_port -id IP_PORT2 set -remove_current_usages ISCSI
Command line parsing failed near "-remove_current_usages" token. ===> pstcli에는 그러한 옵션이 없음
Syntax error.
cli> ip_port -id IP_PORT2 set -add_current_usages ISCSI
Invalid Request
messages:
code = 0xE0E600701002
severity = Error
message_l10n = The IP port IP_PORT2 does not support the addition of the following usages: ISCSI.
arguments = IP_PORT2, ISCSI
cli> ip_port -id IP_PORT2 set -add_current_usages External_Replication
잘못된 요청
메시지:
code = 0xE0E200702005
severity = Error
message_l10n = Multiple networks can be used for External_Replication. 타겟 네트워크 식별자를 명시적으로 지정해야 합니다.
arguments = External_Replication