Search Results (293)
Conversation Type :
Posts
Published Date :
Lifetime
Category
Official Solution
Is there a way to fun a firmware update just on the iDrac firmware on all my servers at once?
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
Hello everyone, I'm assuming that I'm not doing something quite right or that I'm overlooking something. I have rolled out new local iDRAC users on a server using a template. I have created the template from a reference system The message after the job is done looks like this: #### SummaryAct
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
Hello all, we have S4820T switches that we want to configure SNMP on it. When we try to configure the SNMP after going to config mode we are getting error: Error: Invalid input at "^" marker. sw01(conf)#snmp? ^% E
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
I have a ticket number for a specific case & would like to know its status
Question
•
Dell OpenManage Enterprise
Official Solution
Hello! I have run into an issue with a server on a jobsite with one of the hard drives failing and in need of replacement. It's a Dell PowerEdge T630. I am wondering how to see if the HD is hot swappable. I am hoping I can check remotely, so I don't have to go back and fourth from site/or coordinate
Question
•
Dell OpenManage Enterprise
Official Solution
I know that there is already a conversation about this topic but it was in 2019 and I wanted to make sure that I didn’t miss an update that added giving permissions for specific users to manage static groups
Question
•
Dell OpenManage Enterprise
Official Solution
We currently have our SNMP alerts forwarding fine, but when the Message ID CDEV6130 (Device went offline) occurred, we did not get an alert emailed to us. What is the specific category that is needed to be added within out Alert Policy to have that message ID emailed as well? Thanks.
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
Official Solution
Hello together, i want to migrate our openmanage 3.10.2 to 4.10 but i'm a little bit confused about these Prerequisites that is mentioned in the vsphere article Ensure that any ESXi to be deployed is disconnected from vCenter. What does this mean? Should i disconnect the esxi host from the vCe
Question
•
Dell OpenManage Enterprise
Official Solution
Hello , I discover all of my Devices at the same Way over the OME . I choose Server / IDARC and then i put in the IP Address , the user and the Password of the IDRAC of the Device. But after onboardingof the Device , some Devices shows up as "internel" and others as "Discovery" under C
Question
•
Dell OpenManage Enterprise
Official Solution
Hello everyone, I have a question about baselines. I have created a baseline for checking/monitoring user accounts on servers. When I created the baseline, the corresponding status on the servers was initially checked immediately. So far clear. However, the baseline displayed the error “Not complia
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
Official Solution
Hello, The widget "Firmware" doesn´t works anymore. The overlay for selection your baseline comes up but it redirects back to the frontpage when selecting the one. Firmware wiget always takes you back to the main page Why Firmware widget not works? How to fix
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
Hello , I have to disable SSH on all of my Dell IDRACs because of Security Reasons . I also want to configure SNMP with our Community String . I created an Template to rollout to al IDRACS so that SNMP become enable and also shows our Community String . That works fine and i can choo
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
Hello together, I am asking for a friend...After we have discovered a new server with OME 4.1.0, a new user (OME_29fbxxxxx) with the Administrator user role appears on the iDRAC board under the local users. So far we have no idea how this is generated and why. We have only been using this latest OME
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
So did not find anything on the board that helpt with this error. Fresh 4.1 ovf againt an updated 3.10.2 (build 13) And afer multiple tries keep this error Source appliance not ready (not in MAINTENANCE state). 'Migrate Out' steps 2 and 3 must be completed on the source appliance. Needless to say
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
Hello, I understand that when deploying the appliance that 2*415GB hard drives are required. Do both hard drives need to reside on the same datastore or can they reside on 2 different datastores? Thanks in advance,
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
I have just deployed OpenManage Enterprise 4.0.1 however when I check the catalog management, I get the error: Execution Message Running Processing repository information. Attempting to connect to repository. Downl
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
Hello , When i try to access to alert policy menu in openmanage , i receive a error.This is happend since i have modify one alert policy. ( in the message area ) How can i list and/or remove a alert policy in CLI or other ? Best regards
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
I'm on OME Version 4.0.1 (Build 29) Recently, I discovered about 40 managed systems within OME went missing -- like, completely gone. I had to rediscover the servers, add them back to various Services groups, etc. What was odd was that the systems didn't have the updated root credentials
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
Hello, We have an MX7000 with several MX740C blades. Recently we migrated the OS to BOSS and I removed the SAS drives. Since doing that, each blade is complaining about a missing SAS drive. I tried acknowledging the alerts and even tried clearing the configuration of the PERC. But the built in Open
Question
•
Dell OpenManage Enterprise
Community Accepted Solution
My alert policies are no longer sending emails since upgrading from 3.10 to 4.0.1. I am able to send a test email from Application Settings -> Alerts -> Email Configuration, but no matter what I try I can't get my alert policies to send emails. No settings were changed after the upgrade to 4.
Question
•
Dell OpenManage Enterprise