Passer au contenu principal
Quitter

Bienvenue dans l’univers Dell

Mon compte
  • Passer des commandes rapidement et facilement
  • Afficher les commandes et suivre l’état de votre expédition
  • Profitez de récompenses et de remises réservées aux membres
  • Créez et accédez à une liste de vos produits
  • Gérer vos sites, vos produits et vos contacts au niveau des produits Dell EMC à l’aide de la rubrique Gestion des informations de l’entreprise.
Se connecter Créer un compte Connexion au compte Premier Connexion au programme de partenariat
Nous contacter

Vos paniers Dell.com

Numéro d’article: 000129926

Latitude 3510 Teardown, removal guide for customer replaceable units (CRUs)

Résumé: A guide to safe removal and replacement of those parts of a Latitude 3510 laptop that Dell considers safe and easy for anyone to attempt.

Cet article a peut-être été traduit automatiquement. Si vous avez des commentaires concernant sa qualité, veuillez nous en informer en utilisant le formulaire au bas de cette page.

Contenu de l’article

Symptômes

This guide takes you step by step through the safe removal of the Customer Replaceable Unit (CRU) parts of a Latitude 3510 Laptop. (CRUs are the parts of the laptop that should not need an engineer to remove or replace.) The guide includes pictures to reference what is involved.

Table of Contents:

  1. CRU Removal Guide
  2. Removal Instructions

Cause

Removal Guide

 

If these guides do not cover what you are looking to do, then you must reference your System Manual.

The article below provides information about safe practices to consider before working with electrical equipment.


Back to Top

Résolution

 

Removal Instructions

 

Note: In order to see the contents, click the title of the section you want to open below.
 
|

 

Required Tools

1 Small Phillip's head screwdriver 2 Plastic Scribe
3 Small Flat head screwdriver    
 
Note: Using a large Phillips or Flat Head screwdriver may result in damage to the head of the screws. This would make their removal impossible without specialty tools. Tools that are not available to our onsite engineers.

 

  1. Pre-Removal Instructions before removing the Access Panel:

    1. During installation or removals of any hardware always ensure that all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

  2. Turn the laptop over on its closed lid and loosen the eight (8) captive screws. The screws go around the edge of the panel and secure the access panel to the chassis.

CRU 3510 Door

  1. Using a plastic scribe or some other tool that does not mark the plastics, pry the cover up from the right-hand side hinge. Then work clockwise around the access panel to release it from the chassis.

CRU 3510 Door 02

  1. Lift the panel up and away from the chassis.

 

  1. Pre-Removal Instructions before removing the Memory:

    1. During installation or removals of any hardware always ensure that all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Remove the Access Panel and disconnect the battery cable

  2. With the laptop placed on its closed lid, the memory is located in the top right-hand side corner of the system. Lift the cover away from the memory DIMM.

CRU 3510 Memory

  1. Pull apart the metal clips holding the DIMM in place.

CRU 3510 Memory 02

  1. When the DIMM lifts up at an angle to the base, pull it out of the socket and away from the laptop.

Note: Repeat the steps three and four for any additional memory DIMMs located in the laptop.

 

  1. Pre-Removal Instructions before removing the Solid State Drive (SSD):

    1. During installation or removals of any hardware always ensure that all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Remove the Access Panel and disconnect the battery cable

  2. With the laptop on its closed lid, the SSD is located in under the laptop fan on the left-hand side corner of the laptop.

For the M.2 2280 SSD:

  1. Remove the single (1) screw that secures the M.2 2280 SSD to the chassis and the card springs up at an angle to the motherboard.

CRU 3510 SSD

  1. Maneuver the SSD card out of the SSD connector and away from the laptop.

For the M.2 2230 SSD:

  1. Remove the single (1) screw that secures the M.2 2230 SSD to the chassis and the card springs up at an angle to the motherboard.

CRU 3510 SSD 03

  1. Maneuver the SSD card out of the SSD connector and away from the laptop.

 

  1. Pre-Removal Instructions before removing the Laptop Fan:

    1. During installation or removals of any hardware always ensure that all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Remove the Access Panel and disconnect the battery cable

  2. With the laptop on its closed lid, the fan is located in the top right-hand side corner of the laptop. Disconnect the I/O board cable from the motherboard and unroute it from around the fan assembly.

CRU 3510 Fan

  1. Remove the two (2) screws that secure the fan to the chassis.

  2. Unroute the WLAN antenna cables from around the fan assembly.

CRU 3510 Fan 02

  1. Disconnect the fan cable from the motherboard and lift the fan assembly up and away from the chassis.

 

  1. Pre-Removal Instructions before removing the Coin Cell Battery:

    1. During installation or removals of any hardware always ensure that all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Remove the Access Panel and disconnect the battery cable

  2. With the laptop on its closed lid, the coin-cell battery is located to the left of the laptop fan. Disconnect the coin-cell battery cable from the motherboard.

CRU 3510 Coin Cell

  1. Lift the coin-cell battery away from the adhesive on the motherboard.

 

  1. Pre-Removal Instructions before removing the Micro-SD Memory Card:

    1. During installation or removals of any hardware always ensure that all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

  2. The Micro SD slot is located on the right-hand edge of the laptop. Push in gently on the card in the slot and release to have it pop out of the slot [1].

CRU 3510 MSD

  1. Grip the card and pull it the rest of the way out of the slot [2].

 

  1. Pre-Removal Instructions before removing the SIM Card:

    1. During installation or removals of any hardware always ensure that all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

  2. The Micro SIM slot is located on the right-hand edge of the system. Open the latch that covers the SIM card slot [1] and push a SIM card tool or a straightened paper clip gently into the hole on SIM card slot filler [2] until it pops out of the slot [3].

CRU 3510 SIM

  1. Remove the filler and remove the SIM card [4] and push the filler back into the laptop until it locks in place.

 

  1. Pre-Removal Instructions before removing the WLAN Card (WiFi, Wireless):

    1. During installation or removals of any hardware always ensure that all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Remove the Access Panel and unplug the battery cable

  2. With the laptop on it is closed lid, the WLAN card is located in the center of the laptop.

  3. Remove the single (1) screw that secures the WLAN card bracket to the chassis.

CRU 3510 WLAN

  1. Remove the bracket from on top of the antenna cables and the card appears at an angle from the motherboard.

  2. Disconnect the antenna cables pop connectors from the press studs on the WLAN card.

CRU 3510 WLAN 02

  1. Pull the card out of the connector on the motherboard and away from the laptop.

Informations supplémentaires

If you require further assistance, contact Technical Support.

 

  Contact Us  

Propriétés de l’article

Produit concerné

Latitude 3510

Dernière date de publication

16 mai 2023

Version

5

Type d’article

Solution

Haut de la page