Precision Workstation: RAID Controller Setup
Summary: The following article talks about the Dell Precision Fixed Workstations and setting up RAID using the RAID controller cards.
This article applies to
This article does not apply to
This article is not tied to any specific product.
Not all product versions are identified in this article.
Instructions
Table of Contents:
- Different models of RAID controller cards available
- Understanding RAID terms and concepts
- RAID BIOS Configuration Utility
- RAID Storage driver
- Using and Understanding the LSI 9271-8i RAID Controller
Different models of RAID controller cards available
Dell Precision workstations offer several options for hard drive controllers:
- ✓ Dell H310 PCIe RAID card
- ✓ Dell H710P PCIe RAID card
- ✓ Dell H330 PCIe RAID card
- ✓ Dell H730P PCIe RAID card
- ✓ LSI 9271-8i RAID Controllers
Both the H310 and H710P cards offer multiple 6 Gb/s ports for SATA, SAS, or SSD drives. They support RAID 0, 1, 5, and 10 configurations.
The H310 is a host-based RAID card. Host-based means that system processor cycles are used to implement the RAID.
(Figure.1 PERC H310)
The H710P is a hardware RAID controller. Hardware RAID means that all the processing needed for RAID occurs on the card; no system processor cycles are used. Hardware RAID puts less burden on the workstation processor and provides the utmost performance for your workstation. (This card supports Internal storage only.)
(Figure.2 H710p)
Both the H330 and H730P cards offer multiple 12 Gb/s ports for SATA, SAS or SSD drives. They support RAID 0, 1, 5 and 10 configurations.
The H330 is a general-purpose RAID solution card. (This card supports both Internal storage and Tape Devices but does not support Caching. This can affect performance in RAID 5 and RAID 6 arrays.)
(Figure.3 H330)
The H730P is a Hardware RAID. This card has a 1 GB or 2 GB nonvolatile cache. (This card supports Internal storage only.)
(Figure.4 H730p)
The RAID BIOS Configuration Utility, otherwise known as Dell OpenManage Storage Services is a storage management application. This application is embedded on the various cards that configure and maintains RAID disk groups and virtual disks. This utility is independent of the operating system. Press the <CTRL + R> keys together during POST to enter this utility.
For Information on the LSI 9271-8i RAID Controllers, check out the Videos below in section 5.
(Figure.5 PERC LSI)
Note: These same cards are also used in Dell Enterprise Server systems. They are also known as PowerEdge Redundant Arrays of Inexpensive Disks (RAID) Controller (PERC) cards. They are the same card.
Understanding RAID terms and concepts
We have included several videos below to go through the basic concepts and terms used in RAID. Videos may be English only or have local captions available.
These should be helpful to you if you have no prior experience with RAID. If you have you can go to the next section.
Introduction to RAID Concepts
Duration: 00:01:30 (hh:mm:ss)
Closed captions: (English Only.)
Understanding RAID Levels
Duration: 00:03:35 (hh:mm:ss)
Closed captions: (English only.)
Understanding Parity
Duration: 00:01:41 (hh:mm:ss)
Closed captions: (English only.)
Understanding Strip Size, Stripe Width and Stripe Size
Duration: 00:01:24 (hh:mm:ss)
Closed captions: (English Only.)
RAID BIOS Configuration Utility
Before loading the PERC controller drivers, you must set up the RAID with the help of this utility.
The utility for the older cards has several sections including Virtual Disk Management, Physical Disk Management, Controller Management, and Properties.
(Figure.6 PERC Utility)
The utility for the newer cards is identical, but it changes properties to Foreign Configuration View.
(Figure.7 BIOS PERC6i)
RAID Storage driver
When installing/reinstalling a Windows operating system, set-up prompts for a RAID Storage driver at some point during installation. An on-site engineer or user must have the RAID storage driver ready on a USB drive when trying to format and load the operating system.
Below is a screenshot of no hard disk drive found in the Windows 7 installation: (No significant change for newer versions of Windows.)
(Figure.8 PERC Driver)
If you receive the no Hard disk drive found message, then the USB drive with the driver must be plugged in. Click on Load Drivers and browse to the driver's location on the USB drive and run it.
You can download the drivers from the Dell Support Site.
Ensure you enter your Service Tag or Express Service Code to ensure you get the correct page up. (You can also select your model type from the product list.)
You must click on the Drivers & Downloads button on the left-hand side of the page and then make sure your operating system is selected correctly.
Open the Storage Controller section and download the driver file from the link.
Using and Understanding the LSI 9271-8i RAID Controller
The videos below should take you through the uses of the LSI 9271-8i RAID Controllers and hopefully give a better understanding of them. Videos may be English only or have local captions available.
Updating the Firmware on LSI 9271-8i RAID Controllers
Duration: 00:01:50 (hh:mm:ss)
Closed captions: (English Only.)
Foreign Configurations on LSI 9271-8i RAID Controllers
Duration: 00:01:39 (hh:mm:ss)
Closed captions: (English Only.)
Additional Information
Recommended Articles
Here are some recommended articles related to this topic that might be of interest to you.
Affected Products
Fixed WorkstationsArticle Properties
Article Number: 000133184
Article Type: How To
Last Modified: 17 Apr 2024
Version: 5
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.