Article Number: 000128606
These guides take you step-by-step through the safe removal of the Customer Replaceable Unit (CRU) parts of a Latitude 7410 Notebook and 2-in-1 system. (CRUs are the parts of the system that should not need an engineer to remove or replace.) The guides include pictures to reference what is involved.
If these guides do not cover what you are looking to do, then you will want to reference your System Manual.
The article below provides information about safe practices to take into consideration before working with electrical equipment.
1 | Small Phillip's head screwdriver | 2 | Plastic Scribe |
3 | Small Flat head screwdriver |
Pre-Removal Instructions before removing the Access Panel:
During installation or removals of any hardware always ensure that all data is backed up properly
Disconnect any telephone, network, or USB cables from the computer
Disconnect the computer and all attached devices from their electrical outlets
Turn the system over on its closed lid and loosen the eight (8) captive screws securing the access panel to the chassis
Using a plastic scribe or some other tool that will not mark the plastics, pry the cover up from the top left-hand side corner and work clockwise around the access panel to release it from the chassis
Lift the panel up and away from the chassis
Pre-Removal Instructions before removing the Solid State Drive (SSD):
During installation or removals of any hardware always ensure that all data is backed up properly
Disconnect any telephone, network, or USB cables from the computer
Disconnect the computer and all attached devices from their electrical outlets
Please remove the Access Panel and disconnect the battery cable
With the system on its closed lid, the SSD is located in the upper, center of the system.
Remove the single screw that secures the thermal plate and remove the thermal plate from on top of the SSD
2230 SSD
Remove the single screw that secures the SSD to the chassis and lift it out of the M.2 connector and system
2280 SSD
Remove the single screw that secures the SSD to the chassis and lift it out of the M.2 connector and system
Pre-Removal Instructions before removing the MicroSD Memory Card:
During installation or removals of any hardware always ensure that all data is backed up properly
Disconnect any telephone, network, or USB cables from the computer
Disconnect the computer and all attached devices from their electrical outlets
The Micro SD slot is located on the left-hand edge of the system. Push in gently on the card in the slot and release to have it pop out of the slot
Grip the card and pull it the rest of the way out of the slot
Pre-Removal Instructions before removing the SIM Card:
During installation or removals of any hardware always ensure that all data is backed up properly
Disconnect any telephone, network, or USB cables from the computer
Disconnect the computer and all attached devices from their electrical outlets
The SIM slot is located on the right-hand edge of the system. Push a SIM card tool or a straightened paper clip gently into the hole on the left-hand side of the SIM card slot filler until it pops out of the slot
Remove the filler and fit the SIM card and push the filler back into the system until it locks in place
Pre-Removal Instructions before removing the WWAN Card (Cellular):
During installation or removals of any hardware always ensure that all data is backed up properly
Disconnect any telephone, network, or USB cables from the computer
Disconnect the computer and all attached devices from their electrical outlets
Please remove the Access Panel and disconnect the battery cable
With the system on its closed lid, the WWAN card is located in the top left-hand corner of the system. Remove the single (1) screw that secures the WWAN shielding cover to the chassis
Using a plastic scribe, pry the shielding cover from on top of the antenna cables and the card will pop up at an angle from the motherboard
Disconnect the antenna cables pop connectors from the press studs on the WWAN card
Pull the card out of the connector on the motherboard and away from the system
Pre-Removal Instructions before disconnecting the WLAN Antennae (WiFi, Wireless):
During installation or removals of any hardware always ensure that all data is backed up properly
Disconnect any telephone, network, or USB cables from the computer
Disconnect the computer and all attached devices from their electrical outlets
Please remove the Access Panel and disconnect the battery cable
With the system on its closed lid, the WLAN module is located between the system fan and the SSD in the center of the system. Remove the single (1) screw that secures the WLAN antennae bracket to the chassis
Remove the bracket from on top of the antenna cables and disconnect the antenna cables pop connectors from the press studs on the WLAN module
If you require further assistance, please contact Technical Support.
Contact Us |
Latitude 7410
24 May 2024
5
Solution