Skip to main content
Welcome
Dell Sites
Dell Technologies
Premier Sign In
Partner Program Sign In
Support
Dell Sites
Dell Technologies
Premier Sign In
Partner Program Sign In
Support
Sign Out
Welcome to Dell
My Account
Place orders quickly and easily
View orders and track your shipping status
Create and access a list of your products
Sign In
Create an Account
Premier Sign In
Partner Program Sign In
AE/EN
Support
Back
Support
Support Home
Support Library
Support Videos
Support Services & Warranty
Drivers & Downloads
Manuals & Documentation
Diagnostics & Tools
Self-Repair & Parts
Service Requests & Dispatch Status
Contact Technical Support
Community
Find a Partner
AE/EN
Back
Home
Support
Knowledge Base Article
Print
Email
简体中文
Česky
Dansk
Deutsch
English
Español
Suomi
Français
Italiano
日本語
한국어
Nederlands
Norsk
Polski
Português
Русский
Svenska
Türkçe
繁體中文
Українська
简体中文
Dell EMC Networking OS10:接口中继模式配置
Table of Contents
Detailed Article
Instructions
Additional Info
Affected Products
Provide Feedback
Summary:
如何在接口上配置 OS10 中继模式
Detailed Article
Instructions
Additional Info
Affected Products
Provide Feedback
Please select a product to check article relevancy
This article applies to
This article does not apply to
This article is not tied to any specific product.
Not all product versions are identified in this article.
Check out other resources
Identify Your Product
Instructions
前提条件:
交换机具有出厂默认配置,并配置了 VLAN 10 和 11。
指示
设置管理接口网络连接的说明:
使用 S 系列交换机的控制台或管理 IP 打开 CLI。
以默认管理员凭据身份登录到特权执行模式。
(OS10:user=admin,password=admin)。
显示接口的状态,注意“访问”模式的 A:
OS10#
显示接口状态
观察 Eth 1/1/14 界面,如下所示。它处于访问 A 模式。
要修改交换机配置,请运行“configure terminal”命令,然后按 Enter 键。
OS10#
配置终端
OS10(config)#
要配置以太网 1/1/14 接口,请输入“接口以太网 1/1/14”命令:
OS10(config)#
接口以太网 1/1/14
OS10(conf-if-eth1/1/14)#
要使用“switchport mode trunk”命令将接口模式更改为中继,请执行以下操作:
OS10(conf-if-eth1/1/14)#
交换机端口模式中继
OS10(conf-if-eth1/1/14)#
使用“switchport trunk allowed vlan 10,11”配置将哪些中继 vlan 分配给接口。
OS10(conf-if-eth1/1/14)#
switchport trunk allowed vlan 10,11
OS10(conf-if-eth1/1/14)#
使用命令“
switchport access vlan 1
”配置将哪个访问 vlan 分配给端口。
OS10(conf-if-eth1/1/14)#
交换机端口访问 vlan 1
OS10(conf-if-eth1/1/14)#
使用命令“end”将接口和配置退出回执行模式。
OS10(conf-if-eth1/1/14)#
end
OS10#
使用命令“
show running-configuration interface ethernet 1/1/14”
验证在接口上进行的配置更改
要使用命令“show interface status”验证对接口的更改。验证模式现在是中继的 T。将应用访问 VLAN 1,并分配标记的 VLANS 10 和 11。
要保存配置更改,请使用命令“write memory”。
OS10#
写入内存
OS10#
如需进一步帮助,请参阅
Dell EMC SmartFabric OS10 用户指南版本文档
或联系 Dell EMC 技术支持。
Additional Information
请参阅此视频:
Affected Products
Enterprise SONiC Distribution
Article Properties
Article Number:
000201923
Article Type:
How To
Last Modified:
10 Oct 2022
Version:
2
Find answers to your questions from other Dell users
Visit Community
Support Services
Check if your device is covered by Support Services.
Check Support Status
Article Properties
Article Number:
000201923
Article Type:
How To
Last Modified:
10 Oct 2022
Version:
2
Find answers to your questions from other Dell users
Visit Community
Support Services
Check if your device is covered by Support Services.
Check Support Status