Search

Hi all, we use ppdm 19.14, and until now no issue found for backup daily or etc, but on report browser we try to generate data, and display "No data to display", this also happens with daily report send to mail attach .csv file no data on there. and if we back date on generate data before June 25,

We just finished migrating our domain controllers from Windows Server 2012 R2 to Windows Server 2022. Immediately after the last 2012 R2 domain controller was demoted we started getting the following error on our Unity NAS devices. Domain Controller servers configured for the SMB server *** are not

I am seeing the folllowing error message on one of my disks. Disk health code too many medium errors Seems to be a faulty disk. This disk also has been allocated to host production data. How can i safely swap for a good one if its faulty?

Hi everyone, I'd like to know how to check the compatibility of an SPS for my VNX 5500.

Hi Guys, We have a DD4500 and suddenly it crashes , when we reinsert the AC power cable we get a black screen of the console. an amber led in the front of the SP Module. drives and the rest of the module are off exept the management module. can i confirm that the SP module should be replaced ?

Hello, I am new to unity, and I need know that when we display the file systems for NAS server. The Size shows = 10GB The Used shows = 1.8GB The Allocated shows = 0.5GB Shouldn't the Size and Allocated be same? why it is different? what am I missing? There is no quota set on the file system.

Hi, I need to delete a directory that is giving me operation not permitted. Prior, I successfully copied the data to another diectory, but I also had another policy to a different array. Later I forgot to break the association and ended up deleting the policy. The array is currently running 9.2. Is

Folks Anyone could me explain this message "Write cache is currently down...."    

Hi, I have a question about how I can see the power consumption of power supplies in a PowerStore, either through the API or via CLI. Any ideas? Regards

Hi Folks Anyone could explain what is mean? What do I need to do? Thank you

Hi Folks Any one already replaced the battery on SCv2020? Is there any procedure? Thank you  

Hi Folks In my last post I was looking for a way to access the storage, now I can access. However, in my environment with Hyper V after setup the SAS Domain 1 and 2 and see status of the card UP, when I want to create a server, only bottom SAS is showing and if I try to Add HBA manually, the HBA co

We have server a, b, c and lun0 1 and 2.   All three hosts have acces to all 3 luns.  If I am on server a and add a file to lun0 server b and c dont see it.  And then within minutes the data is corrupted.  This is a new setup    any ideas?  I worked with prof

I recently ran a pen test on my environment. The result was that at least one iscsi target is configured not to use authentication. The following iSCSI targets allow unauthenticated access -iqn.2002-03.com.compellent:5000d31004731231 The pen test report said to configure authentication on the targ

Hi Dell support, Our ISILON L400 cannot transfer files and keeps prompting Error 0x8007003B. All our users receiving this error. How to resolve this issue. Our shared folder (SMB) is not fully consumed and has a lot of free space. We need your help! Thank you! Je- M    

There are two controllers,The standby side controller battery has failed and is about to be replaced.The active controller is working normally,Is there any problem if I remove and replace only the standby controller while the power is on?

Hello, I manages 6 OSTs. Each OST fills with 12 disks in 5 drawers and sets up as RAID 6 with 6 VG disk groups.On 3 OSTs, i have 1 failed disk. From the MDSM gui, i can see the failed disk status is Degraded and has the red X.My question is:* I can have the OST up and running, while pulling out the

Hi, My switchport 1 is configure as : But as you can see there is acces + trunk mode. The acces is useless and I need to delete it but I don't found the command, can you help me ?   Thanks a lot !

Hi, I have one disk in a failed status that I need to replace. Can you just pull out the failed disk and pop in the new disk while MD 3420 is still on or do i need to shut it down to install the new disk? Once the new

Hello, Hope, I'm on the correct thread posted.We are using SC4020 as our storage and we are using Acronis as Backup application.During backup on acronis, randomly encountered "highly fragmented" disk.I'd like to ask here from community. Is our storage need to be deffrag? How check disk fragmentatio