This post is more than 5 years old
31 Posts
0
2188
Discovering mcdata switch in prosphere
Failed to discover mcdata switch in prosphere.
using ssh discovery service and used the port "22"
using Prosphere 1.6.0.
Any suggetions ?
This post is more than 5 years old
31 Posts
0
2188
Failed to discover mcdata switch in prosphere.
using ssh discovery service and used the port "22"
using Prosphere 1.6.0.
Any suggetions ?
Top
ConorLawlor
2 Intern
2 Intern
•
233 Posts
1
November 15th, 2012 05:00
Hi Saul_K,
The SMI-S is used to discover Brocade and McDATA switches in ProSphere.
From the ProSphere deployment guide the CMCNE will discover and report back on McDATA switches.
The standalone Brocade SMI Agent for EOS Products v2.7.2 for mcdata switches is not listed in the ProSphere Support Matrix so do not use this to discover the mcdata switches.
Please use the Integrated SMI Agent which comes with CMCNE.
Brocade offers the Integrated SMI Agent that combines management of both FOS and M-EOS devices into a single agent.
The latest version of CMCNE supported with ProSphere 1.6.0.2 is 11.1.4
CMCNE 11.2.x will not be supported til the next release of ProSphere 1.7
Brocade stopped developing the Standalone SMI agents for Brocade and Mcdata switch discovery the latest version of this agent comes as an Integrated Agent as part of Connectrix Manager Converged Network (CMCNE) and supports for later firmware’s will be added to this agent. https://support.emc.com/products/23304_CMCNE please note the full version of CMCNE requires a license. But CMCNE can be installed and setup to run without a license for the Integrated SMI Agent. When asked to Choose the appropriate edition to install Select the SMI Agent only option.
Discovery the switches in CMCNE. Then create an Access Credential and discovery job in ProSphere pointing at host where the Integrated SMI Agent is installed.
ProSphere 1.6.0.1 is supported to work with CMCNE/BNA 11.1.x
Regards
Conor
Saul_K
31 Posts
0
November 15th, 2012 02:00
Or do we need to use SMI-S for discovering mecdata switch ? using port 5988 (Non-Secure (EMC & Brocade)) ??
Saul_K
31 Posts
0
November 15th, 2012 22:00
Thanks Conor
haber_caio
15 Posts
0
November 29th, 2012 05:00
Hi Conor,
Is a license required to install CMCNE with SMI Agent only?
Does brocade SMI Agent 120.11 supports FOS v7.0.0a ?
Thank you very much.
Caio
ConorLawlor
2 Intern
2 Intern
•
233 Posts
1
November 29th, 2012 06:00
Hi Caio,
Is a license required to install CMCNE with SMI Agent only?
No license required just to install the SMI Agent during the installation of CMCNE, When asked to Choose the appropriate edition to install within the installation wizard of CMCNE. Select the SMI Agent only option this way it will not request you for a CMCNE license.
Does brocade SMI Agent 120.11 supports FOS v7.0.0a ?
No, Only supports upto FOS 6.4x
http://www.brocade.com/downloads/documents/support_plans/SMIAGENT/120.11.0/smiagent120.11.0_releasenotes_v1.0.pdf
Regards
Conor
haber_caio
15 Posts
0
November 29th, 2012 07:00
Hi Conor,
Thank you for your fast reply!
Regards,
Caio