Unsolved
3 Posts
0
51
MD3200i controller went offline
One of my controllers went offline with the message:
Event Message: Alternate RAID controller held in reset Event Priority: Critical Component Type: RAID Controller Module Component Location: Enclosure 0, Slot 0
When I connect the serial port to PuTTY, this is what happens when booting:
-=<###>=-
Instantiating /ram as rawFs, device = 0x1
Formatting /ram for DOSFS
Instantiating /ram as rawFs, device = 0x1
Formatting...Retrieved old volume params with %38 confidence:
Volume Parameters: FAT type: FAT32, sectors per cluster 0
0 FAT copies, 0 clusters, 0 sectors per FAT
Sectors reserved 0, hidden 0, FAT sectors 0
Root dir entries 0, sysId (null) , serial number 10000
Label:" " ...
Disk with 1024 sectors of 512 bytes will be formatted with:
Volume Parameters: FAT type: FAT12, sectors per cluster 1
2 FAT copies, 1010 clusters, 3 sectors per FAT
Sectors reserved 1, hidden 0, FAT sectors 6
Root dir entries 112, sysId VXDOS12 , serial number 10000
Label:" " ...
Instantiating /ram as rawFs, device = 0x1
OK.RTC Error: Real-time clock device is not working
Adding 13891 symbols for standalone.
Length: 0x13c Bytes
Version ver03.0A
Reset, Power-Up Diagnostics - Loop 1 of 1
3600 Processor DRAM
01 Data lines Passed
02 Address lines Passed
3300 NVSRAM
01 Data lines Passed
4410 Ethernet 82574 1
01 Register read Passed
02 Register address lines Passed
6D40 Bobcat
02 Flash Test Passed
3700 PLB SRAM
01 Data lines Passed
02 Address lines Passed
7000 SE iSCSI BE2 1
01 Register Read Test Passed
02 Register Address Lines Test Passed
03 Register Data Lines Test Passed
3900 Real-Time Clock
01 RT Clock Tick Passed
Diagnostic Manager exited normally.
Current date: 02/02/24 time: 02:51:00Send <BREAK> for Service Interface or baud rate change
02/02/24-15:21:18 (tRAID): NOTE: Set Powerup State
02/02/24-15:21:18 (tRAID): SOD Sequence is Normal, 0 on controller A
02/02/24-15:21:19 (tRAID): NOTE: Turning on tray summary fault LED
02/02/24-15:21:19 (tRAID): NOTE: Installed Protocols: <MTPs: INIC SAS USB > <ITPs: RDMA ISER IPOIB > <STPs: FCP RmtDMA iSCSI SAS >
02/02/24-15:21:19 (tRAID): NOTE: Required Protocols: <MTPs: INIC SAS > <ITPs: UNK > <STPs: iSCSI SAS >
02/02/24-15:21:19 (tRAID): NOTE: loading flash file: iSCSI
From looking at the other posts, this boot sequence doesn't appear to have gotten far. I had seen another post suggesting to install the latest firmware, but since I can't even connect to it from PowerVault Storage Manager, I think the controller just needs to be replaced?
The other running controller appears to be running firmware 07.84.53.60.
Thanks... Mike
MikeWozFL
3 Posts
0
February 2nd, 2024 16:07
Sending BREAK through PuTTY didn't do anything, BTW.
MikeWozFL
3 Posts
0
February 2nd, 2024 16:43
I was actually able to get it into Service Mode and Recovery Guru says that Battery Replacement Required. I ordered a battery and will see if this helps.