Start a Conversation

Unsolved

This post is more than 5 years old

1953

August 1st, 2012 14:00

spinfab

we have huawei dwdm fc200 2.125G   fiber link connect two DataCenter , when we issue spinfab we got the below error , kindly advice

DCX-Lower-sw01:admin> spinfab -ports 2/19

Running spinfab ..............

ERROR: DIAG PORTSTOPPED spinfab:spinfab, 0 nMegs,

Pt2/19(66) Ch1/26 No Longer Transmitting, FTX Counter Stuck at 89583125,

Err# 13A012E 0242

spinfab: Completed 11 megs, status:  FAILED.

         port 83 test status: 0x00000002 --  FAILED.

  FAILED.

DCX-Lower-sw01:admin>

kindly note link transfer rate is slow we got as max 16MB/s.

siwtches DS-4900B FOS v5.1.0a

DCX-4S  FOS v6.4.2a

is there any parameter to change on brocade

----------------

fcping  10:00:00:05:1e:04:be:18

Destination:    10:00:00:05:1e:04:be:18

Pinging 10:00:00:05:1e:04:be:18 [0xfffc01] with 12 bytes of data:

received reply from 10:00:00:05:1e:04:be:18: 12 bytes time:1385 usec

received reply from 10:00:00:05:1e:04:be:18: 12 bytes time:1284 usec

received reply from 10:00:00:05:1e:04:be:18: 12 bytes time:1227 usec

received reply from 10:00:00:05:1e:04:be:18: 12 bytes time:1264 usec

received reply from 10:00:00:05:1e:04:be:18: 12 bytes time:1676 usec

5 frames sent, 5 frames received, 0 frames rejected, 0 frames timeout

Round-trip min/avg/max = 1227/1367/1676 usec

-------------------

DCX-Lower-sw01:admin> islshow

  1: 17-> 23 10:00:00:05:33:5c:98:3a  43 HP_Enc1_sw1     sp:  8.000G bw:  8.000G

  2: 72->  0 10:00:00:05:33:5c:98:3a  43 HP_Enc1_sw1     sp:  8.000G bw:  8.000G

  3: 83-> 44 10:00:00:05:1e:04:be:18   1 Fabric-A        sp:  2.000G bw:  2.000G

--------------

portshow 2/19

portIndex:  83

portName:

portHealth: HEALTHY

Authentication: None

portDisableReason: None

portCFlags: 0x1

portFlags: 0x10004907    PRESENT ACTIVE E_PORT G_PORT LOGICAL_ONLINE LOGIN LED

LocalSwcFlags: 0x0

portType:  17.0

portState: 1    Online

Protocol: FC

portPhys:  6    In_Sync         portScn:   16   E_Port

port generation number:    12098

state transition count:    22

portId:    1b5300

portIfId:    43220802

portWwn:   20:53:00:05:33:25:49:00

portWwn of device(s) connected:

Distance:  normal

portSpeed: N2Gbps

LE domain: 0

FC Fastwrite: OFF

Interrupts:        0          Link_failure: 63         Frjt:         0

Unknown:           0          Loss_of_sync: 22         Fbsy:         0

Lli:               203        Loss_of_sig:  42

Proc_rqrd:         415367     Protocol_err: 0

Timed_out:         0          Invalid_word: 565795

Rx_flushed:        0          Invalid_crc:  0

Tx_unavail:        0          Delim_err:    0

Free_buffer:       0          Address_err:  2

Overrun:           0          Lr_in:        19

Suspended:         0          Lr_out:       13

Parity_err:        0          Ols_in:       3

Suspended:     0      Lr_out:   13
Parity_err:    0      Ols_in:   3
2_parity_err:  0      Ols_out:  36
CMI_bus_err:   0

Port part of other ADs: No

56 Posts

August 7th, 2012 13:00

Output of the portshow and islshow clearly says that the link and sfp both are looking ok on this switch for this ISL port.

It can be due to huwai switch (dwdm) which brocade is not able to troubleshoot end to end link. You can try crossPort test , portloopback test to check further wether any issue on brocade end or not. If portloopback test is fine then you can open a case with your vendor to ask same but I dont think it matter to check spinfab for long ditance ISL's.

No Events found!

Top