This post is more than 5 years old
12 Posts
0
3452
Principal Switch
I have 2 switch that is trunked each other (edge and core).The core switch have the lowest firmware compared to the edge switch.Is there anything wrong with the "principal" and "local" switch setting from the edge switch?Why the principal and the local switch is a different switch from the edge switch?
HELP ME!!!
EDGE switch
Switch WWN is 20:00:00:05:73:be:36:00
CNBJSSW102# sh ver | inc Software next 4
Cisco Nexus Operating System (NX-OS) Software
--
Software
BIOS: version 1.0.19
loader: version N/A
kickstart: version 5.0(4)
system: version 5.0(4)
CNBJSSW102# sh fcdomain domain-list
VSAN 1
Number of domains: 4
Domain ID WWN
--------- -----------------------
0xe3(227) 20:01:00:0d:ec:63:ee:81 [Principal]
0x62(98) 20:01:00:0d:ec:8d:39:41
0x0c(12) 20:01:00:0d:ec:a7:2b:c1
0x0e(14) 20:01:00:05:73:be:36:01 [Local]
VSAN 3
Number of domains: 4
Domain ID WWN
--------- -----------------------
0x03(3) 20:03:00:0d:ec:63:ee:81 [Principal]
0x0a(10) 20:03:00:0d:ec:8d:39:41
0x0c(12) 20:03:00:0d:ec:a7:2b:c1
0x0e(14) 20:03:00:05:73:be:36:01 [Local]
---------------------------------------------------------------------------------------------------------------------------------------------------------
CORE switch
Switch WWN is 20:00:00:0d:ec:63:ee:80
CNBJSSW01# sh ver | inc Software next 4
Cisco Storage Area Networking Operating System (SAN-OS) Software
--
Software
BIOS: version 1.0.16
kickstart: version 3.3(4)
system: version 3.3(4)
CNBJSSW01# sh fcdomain domain-list
VSAN 1
Number of domains: 4
Domain ID WWN
--------- -----------------------
0xe3(227) 20:01:00:0d:ec:63:ee:81 [Local] [Principal]
0x62(98) 20:01:00:0d:ec:8d:39:41
0x0c(12) 20:01:00:0d:ec:a7:2b:c1
0x0e(14) 20:01:00:05:73:be:36:01
VSAN 3
Number of domains: 4
Domain ID WWN
--------- -----------------------
0x03(3) 20:03:00:0d:ec:63:ee:81 [Local] [Principal]
0x0a(10) 20:03:00:0d:ec:8d:39:41
0x0c(12) 20:03:00:0d:ec:a7:2b:c1
0x0e(14) 20:03:00:05:73:be:36:01
healyj
141 Posts
0
December 12th, 2017 07:00
v
Hi there,
In our efforts to clean up the forum, we came across your question / statement.
If the question / statement is still valid, not expired and you need an update please reach out again and we try to get it answered.
As for now we will set it to “answered.”
Regards,
Jim
GlenH
141 Posts
1
June 20th, 2011 17:00
That all looks normal to me.
You will only ever have 1 principal switch per fabric (VSAN) and it is best practice to have the core switch as the principal (which you do).
The principal switch is elected by a priority setting, or if every switch in the fabric has the same priority, then the switch with the lowest WWN will be elected as principal.
The firmware release operating on the switch has no bearing on whether it will be principal or not.
Glen.
RRR
1 Rookie
1 Rookie
•
5.7K Posts
0
July 2nd, 2012 02:00
Are you ok with the answer? If so please mark the question as answered.
mdani1
56 Posts
1
August 7th, 2012 12:00
Mudzaffar,
As mentioned above also every fabric has a single principal switch at one time. Untill it dont fail and new one is elected or manually changed.In your fabric ( looking the outputs ) seems the Core switch is Principal switch.
Now when you logged in the Edge Switch and ran 'show fcdomain domain-list' --> edge switch is the local switch and Core is principal switch.
0xe3(227) 20:01:00:0d:ec:63:ee:81 [Principal]
0x62(98) 20:01:00:0d:ec:8d:39:41
0x0c(12) 20:01:00:0d:ec:a7:2b:c1
0x0e(14) 20:01:00:05:73:be:36:01 [Local]
Now again when you logged in the Core switch and ran 'show fcdomain domain-list' --> core switch is only the principal switch but here local switch is also the Core switch.
0x03(3) 20:03:00:0d:ec:63:ee:81 [Local] [Principal]
In this comands output Local switch means the swich from where you ran comand and so when your comparing both the outputs it is showing different. It is not an error this only helps you to show which is local switch and its good .