- Notes, cautions, and warnings
- Dell PowerEdge R630 system overview
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- Viewing System BIOS
- System BIOS Settings details
- Boot Settings
- Network Settings
- System Security
- System Information
- Memory Settings
- Processor Settings
- SATA Settings
- Integrated Devices
- Serial Communication
- System Profile Settings
- Miscellaneous Settings
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing system components
- Safety instructions
- Before working inside your system
- After working inside your system
- Recommended tools
- Front bezel (optional)
- System cover
- Inside the system
- Cooling shroud
- System memory
- Hard drives
- Removing a 2.5-inch hard drive blank
- Installing a 2.5-inch hard drive blank
- Removing a 1.8-inch hard drive blank
- Installing a 1.8-inch hard drive blank
- Removing a hot swappable hard drive or solid state drive
- Installing a hot swappable hard drive
- Removing a hard drive or a solid state drive from a hard drive carrier
- Installing a hot swappable hard drive into a hot swappable hard drive carrier
- Removing a 1.8-inch hard drive from a hard drive carrier
- Installing a 1.8-inch hard drive into a hard drive carrier
- Optical drive (optional)
- Cooling fans
- Internal USB memory key (optional)
- Expansion cards and expansion card riser
- SD vFlash card (optional)
- IDSDM
- Integrated storage controller card
- Network daughter card
- Processors and heat sinks
- Power supply units (PSU)
- System battery
- Hard drive backplane
- Control panel assembly
- Removing the control panel board–eight hard drive system
- Installing the control panel board–eight hard drive system
- Removing the control panel–eight hard drive system
- Installing the control panel–eight hard drive system
- Removing the control panel–10 hard drive and 24 hard drive system
- Installing the control panel–10 hard drive system and 24 hard drive system
- VGA module
- System board
- Trusted Platform Module
- Technology and Components
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Minimum configuration to POST
- Troubleshooting system startup failure
- Troubleshooting external connections
- Troubleshooting the video subsystem
- Troubleshooting a USB device
- Troubleshooting iDRAC Direct - USB XML configuration
- Troubleshooting iDRAC Direct - Laptop connection
- Troubleshooting a serial input and output device
- Troubleshooting a NIC
- Troubleshooting a wet system
- Troubleshooting a damaged system
- Troubleshooting the system battery
- Troubleshooting power supply units
- Troubleshooting cooling problems
- Troubleshooting cooling fans
- Troubleshooting system memory
- Troubleshooting an internal USB key
- Troubleshooting a micro SD card
- Troubleshooting an optical drive
- Troubleshooting a tape backup unit
- Troubleshooting a drive or SSD
- Troubleshooting a storage controller
- Troubleshooting expansion cards
- Troubleshooting processors
- Getting help
Dell PowerEdge R630 Owner's Manual
Installing a cooling fan
Prerequisites
- Follow the safety guidelines listed in the Safety instructions section.
- Follow the procedure listed in the Before working inside your system section.
NOTE The procedure for installing each
fan is identical.
Steps
- Align the connector at the base of the cooling fan with the connector on the system board.
- Slide the cooling fan into the securing slot until the tab locks into place.
Next steps
Follow the procedure listed in the After working inside your system section.
평점(별 1~5개)을 매겨주십시오.
평점(별 1~5개)을 매겨주십시오.
평점(별 1~5개)을 매겨주십시오.
문서가 도움이 되었는지 여부를 선택하십시오.
의견에는 <>()\와 같은 특수 문자를 사용할 수 없습니다.