- Notes, cautions, and warnings
- About this document
- System overview
- Technical specifications
- Chassis dimensions
- System weight
- Processor specifications
- PSU specifications
- Supported operating systems
- Cooling fan specifications
- System battery specifications
- Expansion card riser specifications
- Memory specifications
- Storage controller specifications
- Drives
- Ports and connectors specifications
- Video specifications
- Environmental specifications
- Initial system setup and configuration
- Pre-operating system management applications
- System Setup
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Minimum to POST and system management configuration validation
- Installing and removing system components
- Safety instructions
- Before working inside your system
- After working inside your system
- Recommended tools
- Optional front bezel
- System cover
- Drive backplane cover
- Air shrouds
- Removing the air shroud
- Installing the air shroud
- Removing the GPU air shroud top cover
- Installing the GPU air shroud top cover
- Removing the GPU air shroud filler
- Installing the GPU air shroud filler
- Removing the GPU air shroud
- Installing the GPU air shroud
- Removing the 2 x 2.5-inch rear drive module air shroud
- Installing the 2 x 2.5-inch rear drive module air shroud
- Removing the 4 x 2.5-inch rear drive module air shroud
- Installing the 4 x 2.5-inch rear drive module air shroud
- Removing the EDSFF E3.S rear drive module air shroud
- Installing the EDSFF E3.S rear drive module air shroud
- Cooling fans
- Removing the cooling fan cage assembly
- Installing the cooling fan cage assembly
- Removing a cooling fan
- Installing a cooling fan
- Removing a 2 x 2.5-inch rear drive module cooling fan
- Installing a 2 x 2.5-inch rear drive module cooling fan
- Removing a 4 x 2.5-inch rear drive module cooling fan
- Installing a 4 x 2.5-inch rear drive module cooling fan
- Removing the EDSFF E3.S rear drive module cooling fan
- Installing the EDSFF E3.S rear drive module cooling fan
- Drives
- Removing a drive blank
- Installing a drive blank
- Removing a drive carrier
- Installing the drive carrier
- Removing the drive from the drive carrier
- Installing the drive into the drive carrier
- Removing an EDSFF E3.S drive blank
- Installing an EDSFF E3.S drive blank
- Removing an EDSFF E3.S drive carrier
- Installing an EDSFF E3.S drive carrier
- Removing an EDSFF E3.S drive from the drive carrier
- Installing an EDSFF E3.S drive into the drive carrier
- Rear drive module
- Drive backplane
- Side wall brackets
- Cable routings
- PERC module
- EDSFF E3.S backplane module
- System memory
- Processor and heat sink module
- Expansion cards and expansion card risers
- Expansion card installation guidelines
- Removing the expansion card risers
- Installing the expansion card risers
- Removing expansion card from the expansion card riser
- Installing an expansion card into the expansion card riser
- Removing the full length expansion card risers
- Installing the full length expansion card risers
- Removing a GPU
- Installing a GPU
- Removing R1 and R4 paddle cards
- Installing R1 and R4 paddle cards
- Optional serial COM port
- Optional VGA port for Direct Liquid Cooling module
- Optional BOSS-N1 module
- System battery
- Optional internal USB card
- Intrusion switch
- Optional OCP NIC card
- Power supply unit
- Trusted Platform Module
- System board
- LOM card, MIC card and rear I/O board
- Control panel
- Upgrade Kits
- Jumpers and connectors
- System diagnostics and indicator codes
- Getting help
- Documentation resources
Dell PowerEdge R760 Installation and Service Manual
Removing the intrusion switch module
Prerequisites
- Follow the safety guidelines listed in the Safety instructions.
- Follow the procedure listed in the Before working inside your system.
- Remove the expansion card riser.
NOTE:Ensure that you note the routing of the cable as you remove it from the system board. Route the cable properly when you replace it to prevent the cable from being pinched or crimped.
Steps
- Disconnect the intrusion switch cable from the connector on the rear I/O board.
- Using a Phillips #1 screwdriver, loosen the screw on the intrusion switch module.
- Slide the intrusion switch module out of the slot on the system.
NOTE:The numbers on the image do not depict the exact steps. The numbers are for representation of sequence.
Figure 1. Removing the intrusion switch module 
Next steps
평점(별 1~5개)을 매겨주십시오.
평점(별 1~5개)을 매겨주십시오.
평점(별 1~5개)을 매겨주십시오.
문서가 도움이 되었는지 여부를 선택하십시오.
의견에는 <>()\와 같은 특수 문자를 사용할 수 없습니다.