- Notes, cautions, and warnings
- About this document
- System overview
- Technical specifications
- Chassis dimensions
- System weight
- Processor specifications
- PSU specifications
- Supported operating systems
- Cooling fan specifications
- System battery specifications
- Expansion card riser specifications
- Memory specifications
- Storage controller specifications
- Drives
- Ports and connectors specifications
- Video specifications
- Environmental specifications
- Initial system setup and configuration
- Pre-operating system management applications
- System Setup
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Minimum to POST and system management configuration validation
- Installing and removing system components
- Safety instructions
- Before working inside your system
- After working inside your system
- Recommended tools
- Optional front bezel
- System cover
- Drive backplane cover
- Air shrouds
- Removing the air shroud
- Installing the air shroud
- Removing the GPU air shroud top cover
- Installing the GPU air shroud top cover
- Removing the GPU air shroud filler
- Installing the GPU air shroud filler
- Removing the GPU air shroud
- Installing the GPU air shroud
- Removing the 2 x 2.5-inch rear drive module air shroud
- Installing the 2 x 2.5-inch rear drive module air shroud
- Removing the 4 x 2.5-inch rear drive module air shroud
- Installing the 4 x 2.5-inch rear drive module air shroud
- Removing the EDSFF E3.S rear drive module air shroud
- Installing the EDSFF E3.S rear drive module air shroud
- Cooling fans
- Removing the cooling fan cage assembly
- Installing the cooling fan cage assembly
- Removing a cooling fan
- Installing a cooling fan
- Removing a 2 x 2.5-inch rear drive module cooling fan
- Installing a 2 x 2.5-inch rear drive module cooling fan
- Removing a 4 x 2.5-inch rear drive module cooling fan
- Installing a 4 x 2.5-inch rear drive module cooling fan
- Removing the EDSFF E3.S rear drive module cooling fan
- Installing the EDSFF E3.S rear drive module cooling fan
- Drives
- Removing a drive blank
- Installing a drive blank
- Removing a drive carrier
- Installing the drive carrier
- Removing the drive from the drive carrier
- Installing the drive into the drive carrier
- Removing an EDSFF E3.S drive blank
- Installing an EDSFF E3.S drive blank
- Removing an EDSFF E3.S drive carrier
- Installing an EDSFF E3.S drive carrier
- Removing an EDSFF E3.S drive from the drive carrier
- Installing an EDSFF E3.S drive into the drive carrier
- Rear drive module
- Drive backplane
- Side wall brackets
- Cable routings
- PERC module
- EDSFF E3.S backplane module
- System memory
- Processor and heat sink module
- Expansion cards and expansion card risers
- Expansion card installation guidelines
- Removing the expansion card risers
- Installing the expansion card risers
- Removing expansion card from the expansion card riser
- Installing an expansion card into the expansion card riser
- Removing the full length expansion card risers
- Installing the full length expansion card risers
- Removing a GPU
- Installing a GPU
- Removing R1 and R4 paddle cards
- Installing R1 and R4 paddle cards
- Optional serial COM port
- Optional VGA port for Direct Liquid Cooling module
- Optional BOSS-N1 module
- System battery
- Optional internal USB card
- Intrusion switch
- Optional OCP NIC card
- Power supply unit
- Trusted Platform Module
- System board
- LOM card, MIC card and rear I/O board
- Control panel
- Upgrade Kits
- Jumpers and connectors
- System diagnostics and indicator codes
- Getting help
- Documentation resources
Dell PowerEdge R760 Installation and Service Manual
Removing R1 and R4 paddle cards
R1 and R4 paddle cards are supported on 24 x 2.5-inch NVMe Gen4 (passive) configuration only.
Prerequisites
- Follow the safety guidelines listed in the Safety instructions.
- Follow the procedure listed in the Before working inside your system.
- Remove the air shroud or remove the GPU air shroud.
- Remove the cooling fan cage assembly.
NOTE:Observe the cable routing before disconnecting the cables.
- Remove the paddle card cable from side wall bracket.
- Disconnect the paddle card cables from the drive backplane.
Steps
Press the blue release tab on the paddle cards and holding the edges lift the paddle cards from the riser connector on the system board.
Figure 1. Removing the R1 paddle card 
Figure 2. Removing the R4 paddle card 
Next steps
평점(별 1~5개)을 매겨주십시오.
평점(별 1~5개)을 매겨주십시오.
평점(별 1~5개)을 매겨주십시오.
문서가 도움이 되었는지 여부를 선택하십시오.
의견에는 <>()\와 같은 특수 문자를 사용할 수 없습니다.