메인 콘텐츠로 이동
로그아웃

환영합니다.

내 계정
  • 빠르고 간편하게 주문
  • 주문 보기 및 배송 상태 추적
  • 제품 목록을 생성 및 액세스
  • 회사 관리를 사용하여 Dell EMC 사이트, 제품 및 제품 수준 연락처를 관리하십시오.
로그인 계정 만들기 프리미어 로그인 Partner Program 로그인
문의처

Dell.com 카트

Dell PowerEdge R760 Installation and Service Manual

PDF

Installing the expansion card risers

Prerequisites

  1. Follow the safety guidelines listed in the Safety instructions.
  2. Follow the procedure listed in Before working inside your system.
  3. Remove the air shroudor remove the GPU air shroud.
  4. If removed, install the expansion cards into the expansion card risers.
NOTE:Install Riser 2 before installing Riser 1 and Riser 3. Install Riser 4 after installing Riser 3.
CAUTION: Do not install GPUs, network cards, or other PCIe devices on your system that are not validated and tested by Dell. Damage caused by unauthorized and invalidated hardware installation will null and void the system warranty.

Steps

  1. If installed, remove the riser blanks and if required loosen the captive screws.
    NOTE:Store the riser blanks for future use. Filler brackets must be installed in empty expansion card slots to maintain Federal Communications Commission (FCC) certification of the system. The brackets also keep dust and dirt out of the system and aid in proper cooling and airflow inside the system.
    Figure 1. Removing the Riser 2 blank
    This image shows Removing the Riser 2 blank
    Figure 2. Removing the Riser 1 blank
    This image shows Removing the Riser 1 blank
    Figure 3. Removing the Riser 3 blank
    This image shows Removing the Riser 3 blank
    Figure 4. Removing the Riser 4 blank
    This image shows Removing the Riser 4 blank
  2. Holding the edges or the touch points, align the holes on the expansion card riser with the guides on the system board.
  3. Lower the expansion card riser into place and press the touch points until the expansion card riser connector is fully seated on the system board connector.
  4. Tighten the captive screws on the risers and system if any.
    Figure 5. Installing the expansion card riser 2
    This image shows Installing the expansion card riser 2
    Figure 6. Installing the expansion card riser 1
    This image shows Installing the expansion card riser 1
    Figure 7. Installing the expansion card riser 3
    this image shows Installing the expansion card riser 3
    Figure 8. Installing the expansion card riser 4
    This image shows Installing the expansion card riser 4

Next steps

  1. If required, reconnect the cables to the expansion card or system board.
  2. Install the air shroudor install the GPU air shroud.
  3. Follow the procedure listed in After working inside your system.
  4. Install any device drivers required for the card as described in the documentation for the card.

본 콘텐츠를 평가해주십시오.

정확함
유용함
이해하기 쉬운
이 문서가 도움이 되셨나요?
0/3000 characters
  평점(별 1~5개)을 매겨주십시오.
  평점(별 1~5개)을 매겨주십시오.
  평점(별 1~5개)을 매겨주십시오.
  문서가 도움이 되었는지 여부를 선택하십시오.
  의견에는 <>()\와 같은 특수 문자를 사용할 수 없습니다.