- Notes, cautions, and warnings
- About this document
- System overview
- Technical specifications
- Chassis dimensions
- System weight
- Processor specifications
- PSU specifications
- Supported operating systems
- Cooling fan specifications
- System battery specifications
- Expansion card riser specifications
- Memory specifications
- Storage controller specifications
- Drives
- Ports and connectors specifications
- Video specifications
- Environmental specifications
- Initial system setup and configuration
- Pre-operating system management applications
- System Setup
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Minimum to POST and system management configuration validation
- Installing and removing system components
- Safety instructions
- Before working inside your system
- After working inside your system
- Recommended tools
- Optional front bezel
- System cover
- Drive backplane cover
- Air shrouds
- Removing the air shroud
- Installing the air shroud
- Removing the GPU air shroud top cover
- Installing the GPU air shroud top cover
- Removing the GPU air shroud filler
- Installing the GPU air shroud filler
- Removing the GPU air shroud
- Installing the GPU air shroud
- Removing the 2 x 2.5-inch rear drive module air shroud
- Installing the 2 x 2.5-inch rear drive module air shroud
- Removing the 4 x 2.5-inch rear drive module air shroud
- Installing the 4 x 2.5-inch rear drive module air shroud
- Removing the EDSFF E3.S rear drive module air shroud
- Installing the EDSFF E3.S rear drive module air shroud
- Cooling fans
- Removing the cooling fan cage assembly
- Installing the cooling fan cage assembly
- Removing a cooling fan
- Installing a cooling fan
- Removing a 2 x 2.5-inch rear drive module cooling fan
- Installing a 2 x 2.5-inch rear drive module cooling fan
- Removing a 4 x 2.5-inch rear drive module cooling fan
- Installing a 4 x 2.5-inch rear drive module cooling fan
- Removing the EDSFF E3.S rear drive module cooling fan
- Installing the EDSFF E3.S rear drive module cooling fan
- Drives
- Removing a drive blank
- Installing a drive blank
- Removing a drive carrier
- Installing the drive carrier
- Removing the drive from the drive carrier
- Installing the drive into the drive carrier
- Removing an EDSFF E3.S drive blank
- Installing an EDSFF E3.S drive blank
- Removing an EDSFF E3.S drive carrier
- Installing an EDSFF E3.S drive carrier
- Removing an EDSFF E3.S drive from the drive carrier
- Installing an EDSFF E3.S drive into the drive carrier
- Rear drive module
- Drive backplane
- Side wall brackets
- Cable routings
- PERC module
- EDSFF E3.S backplane module
- System memory
- Processor and heat sink module
- Expansion cards and expansion card risers
- Expansion card installation guidelines
- Removing the expansion card risers
- Installing the expansion card risers
- Removing expansion card from the expansion card riser
- Installing an expansion card into the expansion card riser
- Removing the full length expansion card risers
- Installing the full length expansion card risers
- Removing a GPU
- Installing a GPU
- Removing R1 and R4 paddle cards
- Installing R1 and R4 paddle cards
- Optional serial COM port
- Optional VGA port for Direct Liquid Cooling module
- Optional BOSS-N1 module
- System battery
- Optional internal USB card
- Intrusion switch
- Optional OCP NIC card
- Power supply unit
- Trusted Platform Module
- System board
- LOM card, MIC card and rear I/O board
- Control panel
- Upgrade Kits
- Jumpers and connectors
- System diagnostics and indicator codes
- Getting help
- Documentation resources
Dell PowerEdge R760 Installation and Service Manual
Installing the EDSFF E3.S backplane module
Prerequisites
- Follow the safety guidelines listed in the Safety instructions.
- Follow the procedure listed in the Before working inside your system.
- Remove the front bezel.
- Remove the cooling fan cage assembly.
- Remove the drive backplane cover.
- If required, remove the air shroudor remove the GPU air shroud.
- Remove the EDSFF E3.S PERC module.
- Remove the EDSFF E3.S drives.
- Disconnect the cables, observe the cable routing.
NOTE:See cable routing section; configuration 45 or 46 for more information.
Steps
- Align the guides on the EDSFF E3.S backplane module with the slots on the system.
- Slide the EDSFF E3.S backplane module towards the rear of the system, until it is firmly secured.
- Using a Phillips #2 screwdriver, tighten the captive screw on the EDSFF E3.S backplane module.
Figure 1. Installing the EDSFF E3.S backplane module 
Next steps
- Connect all the cables, observe the cable routing.
NOTE:See cable routing section; configuration 45 or 46 for more information.
- Install the EDSFF E3.S PERC module.
- Install the cooling fan cage assembly.
- If removed, install the air shroudor install the GPU air shroud.
- Install the drive backplane cover.
- Install the EDSFF E3.S drives .
- Install the front bezel.
- Follow the procedure listed in After working inside your system.
평점(별 1~5개)을 매겨주십시오.
평점(별 1~5개)을 매겨주십시오.
평점(별 1~5개)을 매겨주십시오.
문서가 도움이 되었는지 여부를 선택하십시오.
의견에는 <>()\와 같은 특수 문자를 사용할 수 없습니다.