- Notes, cautions, and warnings
- About this document
- System overview
- Technical specifications
- Chassis dimensions
- System weight
- Processor specifications
- PSU specifications
- Supported operating systems
- Cooling fan specifications
- System battery specifications
- Expansion card riser specifications
- Memory specifications
- Storage controller specifications
- Drives
- Ports and connectors specifications
- Video specifications
- Environmental specifications
- Initial system setup and configuration
- Pre-operating system management applications
- System Setup
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Minimum to POST and system management configuration validation
- Installing and removing system components
- Safety instructions
- Before working inside your system
- After working inside your system
- Recommended tools
- Optional front bezel
- System cover
- Drive backplane cover
- Air shrouds
- Removing the air shroud
- Installing the air shroud
- Removing the GPU air shroud top cover
- Installing the GPU air shroud top cover
- Removing the GPU air shroud filler
- Installing the GPU air shroud filler
- Removing the GPU air shroud
- Installing the GPU air shroud
- Removing the 2 x 2.5-inch rear drive module air shroud
- Installing the 2 x 2.5-inch rear drive module air shroud
- Removing the 4 x 2.5-inch rear drive module air shroud
- Installing the 4 x 2.5-inch rear drive module air shroud
- Removing the EDSFF E3.S rear drive module air shroud
- Installing the EDSFF E3.S rear drive module air shroud
- Cooling fans
- Removing the cooling fan cage assembly
- Installing the cooling fan cage assembly
- Removing a cooling fan
- Installing a cooling fan
- Removing a 2 x 2.5-inch rear drive module cooling fan
- Installing a 2 x 2.5-inch rear drive module cooling fan
- Removing a 4 x 2.5-inch rear drive module cooling fan
- Installing a 4 x 2.5-inch rear drive module cooling fan
- Removing the EDSFF E3.S rear drive module cooling fan
- Installing the EDSFF E3.S rear drive module cooling fan
- Drives
- Removing a drive blank
- Installing a drive blank
- Removing a drive carrier
- Installing the drive carrier
- Removing the drive from the drive carrier
- Installing the drive into the drive carrier
- Removing an EDSFF E3.S drive blank
- Installing an EDSFF E3.S drive blank
- Removing an EDSFF E3.S drive carrier
- Installing an EDSFF E3.S drive carrier
- Removing an EDSFF E3.S drive from the drive carrier
- Installing an EDSFF E3.S drive into the drive carrier
- Rear drive module
- Drive backplane
- Side wall brackets
- Cable routings
- PERC module
- EDSFF E3.S backplane module
- System memory
- Processor and heat sink module
- Expansion cards and expansion card risers
- Expansion card installation guidelines
- Removing the expansion card risers
- Installing the expansion card risers
- Removing expansion card from the expansion card riser
- Installing an expansion card into the expansion card riser
- Removing the full length expansion card risers
- Installing the full length expansion card risers
- Removing a GPU
- Installing a GPU
- Removing R1 and R4 paddle cards
- Installing R1 and R4 paddle cards
- Optional serial COM port
- Optional VGA port for Direct Liquid Cooling module
- Optional BOSS-N1 module
- System battery
- Optional internal USB card
- Intrusion switch
- Optional OCP NIC card
- Power supply unit
- Trusted Platform Module
- System board
- LOM card, MIC card and rear I/O board
- Control panel
- Upgrade Kits
- Jumpers and connectors
- System diagnostics and indicator codes
- Getting help
- Documentation resources
Dell PowerEdge R760 Installation and Service Manual
Installing the drive carrier
Prerequisites
CAUTION:Before removing or installing a drive while the system is running, see the
www.dell.com/storagecontrollermanuals documentation for the storage controller card to ensure that the host adapter is configured correctly to support drive removal and insertion.
CAUTION:Combining SAS and SATA drives in the same RAID volume is not supported.
CAUTION:When installing a drive, ensure that the adjacent drives are fully installed. Inserting a drive carrier and attempting to lock its handle next to a partially installed carrier can damage the partially installed carrier's shield spring and make it unusable.
NOTE:Ensure that the drive carrier's release handle is in the open position before inserting the carrier into the slot.
CAUTION:To prevent data loss, ensure that your operating system supports
hot-swap drive installation. See the documentation supplied with your
operating system.
CAUTION:When a replacement hot swappable drive is installed and the system is powered on, the drive automatically
begins to rebuild. Ensure that the replacement drive is blank or contains
data that you wish to overwrite. Any data on the replacement drive
is immediately lost after the drive is installed.
- Follow the safety guidelines listed in Safety instructions.
- Remove the front bezel.
- Remove the drive carrier or remove the drive blank when you want to assemble the drive into the system.
Steps
- Slide the drive carrier into the drive slot and push until the drive connects with the backplane.
- Close the drive carrier release handle to lock the drive in place.
Figure 1. Installing a drive carrier 
Next steps
평점(별 1~5개)을 매겨주십시오.
평점(별 1~5개)을 매겨주십시오.
평점(별 1~5개)을 매겨주십시오.
문서가 도움이 되었는지 여부를 선택하십시오.
의견에는 <>()\와 같은 특수 문자를 사용할 수 없습니다.