메인 콘텐츠로 이동
로그아웃

환영합니다.

내 계정
  • 빠르고 간편하게 주문
  • 주문 보기 및 배송 상태 추적
  • 제품 목록을 생성 및 액세스
  • 회사 관리를 사용하여 Dell EMC 사이트, 제품 및 제품 수준 연락처를 관리하십시오.
로그인 계정 만들기 프리미어 로그인 Partner Program 로그인
문의처

Dell.com 카트

Dell PowerEdge R760 Installation and Service Manual

PDF

Installing a GPU

Prerequisites

  1. Follow the safety guidelines listed in the Safety instructions.
  2. Follow the procedure listed in Before working inside your system.
  3. If installing a new expansion card, unpack it and prepare the card for installation.
    NOTE:For instructions, see the documentation accompanying the card.
  4. Remove the GPU air shroud top cover.
  5. Remove the GPU air shroud filler.
  6. Remove the full length expansion card riser.
CAUTION: Do not install GPUs, network cards, or other PCIe devices on your system that are not validated and tested by Dell. Damage caused by unauthorized and invalidated hardware installation will null and void the system warranty.
WARNING: Consumer-Grade GPU should not be installed or used in the Enterprise Server products.

Steps

  1. If installed, remove the filler bracket.
    NOTE:Store the filler bracket for future use. Filler brackets must be installed in empty expansion card slots to maintain Federal Communications Commission (FCC) certification of the system. The brackets also keep dust and dirt out of the system and aid in proper cooling and airflow inside the system.
    Figure 1. Removing the filler bracket
    This image shows removing the metal filler bracket
  2. To install the GPU on Riser 1:
    1. Connect the GPU power cable to the GPU card.
    2. Align the connector on the GPU with the connector on the riser.
    3. Insert the GPU into the riser until firmly seated.
    4. Tilt the expansion card holder latch.
    5. Press the card holder latch to secure the GPU card to the riser.
    Figure 2. Installing GPU on Riser 1
    This image shows installing the GPU to riser1
  3. To install the GPU on Riser 4:
    1. Connect the GPU power cable to the GPU card.
    2. Align the connector on the GPU with the connector on the riser.
    3. Insert the GPU into the riser until firmly seated.
    4. Tilt the expansion card holder latch.
    5. Press the card holder latch to secure the GPU card to the riser.
    6. Slide the expansion card latch on the riser.
    Figure 3. Installing GPU on Riser 4
    This image shows installation of GPU to riser 4

Next steps

  1. If removed, install the GPU air shroud.
    NOTE:The GPU air shroud filler must be installed, if single-width GPU card or empty riser is used.
  2. Install the full length expansion card riser.
  3. Install the GPU air shroud top cover.
  4. Follow the procedure listed in After working inside your system.
  5. Install any device drivers required for the card as described in the documentation for the card.

본 콘텐츠를 평가해주십시오.

정확함
유용함
이해하기 쉬운
이 문서가 도움이 되셨나요?
0/3000 characters
  평점(별 1~5개)을 매겨주십시오.
  평점(별 1~5개)을 매겨주십시오.
  평점(별 1~5개)을 매겨주십시오.
  문서가 도움이 되었는지 여부를 선택하십시오.
  의견에는 <>()\와 같은 특수 문자를 사용할 수 없습니다.