Parameter
|
Description
|
AutoLoad={0,
1, 2, 101, 102, 201, 202}
[LoadPkg={0, 1, 2}]
[AddPkg={pkg1_name,
pkg2_name, …}]
[DelPkg={pkg1_name, pkg2_name, …}]
|
AutoLoad — Default is
1. Specifies the firmware update mode. The following are the
values and associated actions:
0 — Disables checking
for image.
1— Enables forced firmware upgrade/downgrade
process. This is the default value.
2 — Enables
comparison/non-forced upgrade process only.
101
— Enables firmware upgrade/downgrade process, but displays a window
with
OK or
Cancel button before the process with a note
of the version to downgrade or upgrade; displays a status complete
window.
102 — Enables firmware upgrade, but displays
a window with
OK or
Cancel button before the process
with a note of the version to upgrade; displays a status complete
window.
201 — Enables firmware upgrade or downgrade
process, but displays a window with
OK button before the process;
displays a status complete window.
202 — Enables
firmware upgrade only, but displays a window with
OK button
before the process; displays a status complete window.
The option LoadPkg specifies how to update the external packages.
If set to 0, this disables checking for packages.
If set to 1 it enable packages upgrade/downgrade process, and if set
to 2, it enables upgrade only.
If LoadPkg is not
in the statement, it will inherit the value of AutoLoad. For example,
if the value is 0, and if AutoLoad=0, 1, and if AutoLoad=1, 101 or
201, and 2 if AutoLoad=2, 102 or 202.
For example,
if you set AutoLoad=1 LoadPkg=0, the firmware is checked, but the
packages are not checked. From ThinOS 8.3, the external packages update
mechanism is changed.
Some packages are default,
and loaded according to value of LoadPkg. For example RTME.
Some packages need additional parameter AddPkg to add.
For example, FR and TCX.The option AddPkg is for adding packages.
It depends on the value of LoadPkg.
The packages
check comes after firmware check. The option DelPkg is for deleting
packages. It does not depend on the value of LoadPkg. The packages
specified in DelPkg are always deleted when loading the ini file.
The value of AddPkg and DelPkg is one package name
or a package name list. For example, AutoLoad=1 AddPkg="FR, TCX" DelPkg=RTME
-
NOTE: The AddPkg and DelPkg options depend on platforms which supports
external packages. So far only Z/D and U class support it. The other
legacy platforms does not support it.
|
AutoPower={yes,
no}
or
Device=cmos AutoPower=(yes,
no)
|
Default is
no.
Yes/no option
on how the system starts when the power is first applied to the thin
client.
If set to yes, then the system starts itself
without waiting for users to press the power button. In cases where
power was lost unexpectedly and if the thin client was shut down properly
before power was lost unexpectedly, when the power is restored, the
thin client will be powered. This setting is useful in a kiosk environment.
Once an AutoPower statement is processed, it alters
the behavior of the thin client until a countermanding statement is
processed. The effect of an AutoPower=yes statement continues even
if the statement is removed from the INI file in which it was found.
Use of the AutoPower option does not interfere with
performing a user directed shutdown.
|
CCMEnable={yes,
no}
[CCMServer=<server_address>]
[GroupPrefix=<prefix>]
[GroupKey=<hashkey>]
[MQTTServer=<mqtt_address>[:<mqtt_port>]]
[AdvancedConfig={
no, yes}]
[CCMDefault={
no, yes}]
[Override={
no, yes}]
|
Default is
no.
CCMEnable — Yes/no option to enable the Cloud Client Manager Agent.
CCMServer — Specifies a IP address or URL address
for the Cloud Client Manager server. Once specified, it is saved in
the non-volatile memory.
GroupPrefix and GroupKey — The options GroupPrefix and GroupKey compose the Group Registration
Key of the Cloud Client Manager server. Once specified, it is saved
in the non-volatile memory.
MQTTServer — Specifies a IP address or URL address for the MQTT server and
MQTT port after the : (colon). Once specified, it is saved in the
non-volatile memory.
AdvancedConfig — Default
is
no. Yes/no option to enable the Cloud Client Manager server
and MQTT server fields in the GUI. If AdvancedConfig=yes is specified,
the Cloud Client Manager server and MQTT server fields in the Cloud
Client Manager UI will be enabled. See also PRIVILEGE parameters in
General
Settings for wnos.ini Files, {username} INI, and $MAC INI Files
.
CCMDefault — Default is
no. Yes/no
option to enable the Configure Cloud management dialog will display
during boot up. If CCMDefault=yes is specified and both the CCMServer
and GroupKey are NULL, the Configure Cloud management dialog will
display during boot up. Input group code to connect to the default
Cloud Client Manager server and default MQTT server. The default CCM
server is
https://us1.cloudclientmanager.com and default
MQTT server is us1-pns.cloudclientmanager.com.
Override — Default is
no. Yes/no option to allow a groupkey
from the INI file to override the previous groupkey. If Override=yes
is specified, the groupkey from the INI file will override the previous
groupkey. The Groupkey can technically be applied in many places.
You can configure the group key in order of priority, that is, if
#1 is defined it will override #2. Groupkey priority policy is listed
below:
-
Local GUI configuration or groupkey
received from CCM in a Group Change command
-
Defined in INI file "ccmenable=yes
groupkey=xxxx"
-
DHCP Option Tag #199
-
NOTE:
The Groupkey assigned in DCHP option #199 and INI parameter
are only used for first time deployment, that is, they only take effect
if CCM is currently disabled or if CCM is enabled but group-key is
NULL.
If DCHP is defined and CCM is enabled or
not NULL: The CCM Group key in the DHCP is ignored since it is configured
manually in local UI or from CCM group change.
If INI is defined and CCM is enabled or not NULL: The CCM Group key
in the INI is ignored since it is configured manually in local UI
or from CCM group change.
-
NOTE:
For
detailed instructions on how to configure CCM in a wnos.ini file to
enable the CCM Agent on supported ThinOS clients, refer to Knowledge
Base Solution #
23875, go to the Knowledge Base at
www.dell.com/wyse/knowledgebase and search
for
23875.
|
DefaultUser={username, $SYS_VAR} |
Specifies the default sign-on
user. See
Table 1: System Variables for a list of system variables for $SYS_VAR.
|
DisableButton={
no, yes}
[DisableRestart={yes,
no}]
|
Default is
no.
Yes/no option to disable the power button.
If you set the option DisableRestart=yes, the radio button
Restart the system in shutdown window is disabled. These settings
are saved permanently and the default value is no.
|
EnableCacheIni |
-
IMPORTANT: Supported
on Wyse 3010 thin client with ThinOS (T10) and Wyse 3020 thin client
with ThinOS (T10D) only.
EnableCacheIni
is no longer supported and cannot be used on platforms other than
the Wyse 3010 thin client with ThinOS (T10). On platforms other than
the Wyse 3010 thin client with ThinOS (T10), EnableCacheIni is replaced
by the MirrorFileServer parameter, see MirrorFileServer parameter
in
Table 2: General Settings for wnos.ini Files Only. Use EnableCacheIni
on Wyse 3010 thin client with ThinOS platform (T10) only. This is
because there is no local flash on Wyse 3010 thin client with ThinOS
(T10) platform, and the MirrorFileServer parameter is not supported
on it.
|
EnableGKey={
yes, no}
|
Default is
yes.
Yes/no option to enable G key reset. G key reset is supported
for Privilege=High in the NVRAM.
|
Exit={
yes, no, all}
|
Default is
yes.
Specifies the INI file processing.
yes — Processing returns to the prior INI file on the next
line after $include.
no — There is no operation.
all — All INI file processing is exited.
|
Include=<$mac.ini file or {username}.ini file> |
<$MAC.ini> Loads /wnos/inc/mac-address.ini.
-
NOTE:
The file name does not include the symbol
: in
the mac address. See also the Exit parameter for information on how
to terminate Include. <{username}.ini> Loads /wnos/inc/{username}-address.ini.
The file name does not include the symbol
: in the {username} address. See also the Exit parameter for information
on how to terminate Include.
|
MirrorFileServer={
no, yes}
|
Default is
no.
Yes/no option to enable the cache all server files functionality.
This enables the cache all server files such as INI files, wallpaper,
bitmap, font, local messages and so on to the local flash when files
are changed in the file server. ThinOS would use the cached files
when files on the file server are unavailable.
-
IMPORTANT: S10
is not supported
|
RootPath=<file server root path> |
This file server root path is entered
into thin client local setup (non-volatile memory). The thin client
immediately uses this path to access files. The directory name \wnos
will be appended to the file server root path entry before use.
|
TerminalName=<name>
[reboot={
no, yes}]
|
TerminalName — Name of
the client comprising a 15-character string. It can also be configured
with system variables. Basically all the variables can be used except
$TN (recursive), $UN, $PW, $DN. However, these are not yet available
when parsing wnos.ini. Additionally combinations like xy$mac, sz$tnxyz
etc are supported.
reboot — Default is
no. Yes/no option to reboot the thin client if the terminal
name is changed.
|
TimeZone=<zone value>
[ManualOverride={
no, yes}]
[daylight={
no, yes}]
[start=MMWWDD end=MMWWDD]
[TimeZoneName=<timezonename>]
[DayLightName=<daylightname>]
|
TimeZone — Specifies the
time zone if the zone is unspecified on the thin client or is used
with ManualOverride. Supported zone values s are listed in the System
Preference dialog box on the thin client and in TimeZone Parameter:
Values.
ManualOverride — Default is
no. Yes/no option to override the thin client
System Preference Menu setting with this TimeZone setting. TimeZone
settings in the wnos.ini file will be saved into NVRAM if EnableLocal=yes
is set in the wnos.ini file.
Daylight — Default
is
no. Yes/no option to enable daylight saving time; MMWWDD
is a 6 digit number to specify the start and the end of daylight saving
time.
-
IMPORTANT: The
Start and End options are in the MMWWDD format, where:
MM = Month of the year. Values are 01 to 12 for the months
of the year from January to December. For example, 01 = January, 12
= December
WW = Week of the Month. Values
are 01 to 05 for the week of the month, 05 is the last week. For example,
01 = 1st week, 05 = the last week of the month.
DD = Day of the week. Values are 01 to 07 for the day in the
week from Monday to Sunday. For example, 01 = Monday, 07 = Sunday.
-
NOTE:
For
the 2013 year, DST dates are Sunday, March 10, 2:00am and ends Sunday,
November 3, 2:00am.
TimeZoneName — Display
name sent to the ICA/RDP session such as Eastern Standard Time.
DayLightName — Display name for daylight
saving time. If daylight saving time is enabled, DayLightName should
be named something similar to Eastern Daylight Time, otherwise it
should be the same as TimeZoneName.
-
NOTE:
To configure
daylight saving time for an RDP session, you must enable the Allow
Time Zone Redirection function. Use the following guidelines:
- Run
gpedit.msc to open the
Group Policy dialog box.
-
Click
Computer Configuration in the Local Computer Policy tree, and expand the
Administrative
Templates
folder.
-
Expand the
Windows Components folder, and then expand the
Terminal Services folder.
-
Click
Client/Server data redirection to open the Setting list.
-
Right-click
Allow Time Zone Redirection and select
Properties to open the
Allow Time Zone Redirection
Properties
dialog box.
-
Select the
Enabled option, and
then click
OK.
-
Close the
Group Policy dialog
box.
Overall Example:
TimeZone="GMT – 08:00"
ManualOverride=yes Daylight=Yes
Start=030107 End=110107
TimeZoneName="Pacific Standard Time"
DayLightName="Pacific Daylight Time"
|