- Notes, Cautions, and Warnings
- About your system
- Initial system
configuration
- Before You Begin
- Initial Setup Sequence
- Initial CMC Network Configuration
- Logging In To The CMC Using The Web-Based Interface
- Adding And Managing CMC Users
- Configuring iDRAC Networking Using The Web-Based Interface
- Setting The First Boot Device For Servers
- Configuring And Managing Power
- Installing Or Updating The CMC Firmware
- Configuring The Optional iKVM Switch Module
- FlexAddress
- FlexAddress Plus
- Configuring
The I/O Modules
- Network Information
- I/O Connectivity
- Port Auto-Disablement in Quad-Port Network Daughter Card (Dell PowerEdge M710HD Only)
- Mezzanine Cards
- I/O Module Port Mapping—Full-Height Blades
- I/O Module Port Mapping─Half-Height Blades
- I/O Modules—Switches
- Configuring A Switch Module Network Ethernet Port Using The Web-Based Interface
- Brocade M6505 16 Gbps FC SAN I/O Module
- Cisco Nexus B22 Fabric Extender Module
- Dell PowerEdge M I/O Aggregator Switch
- Dell Force10 MXL 10/40 GbE Switch
- Mellanox M4001F/M4001Q/M4001T Infiniband Switch I/O Module
- Dell PowerConnect KR 8024-k Switch
- Dell PowerConnect M8428-k 10 Gb Converged Network Switch
- Mellanox M2401G DDR Infiniband Switch I/O Module
- Mellanox M3601Q QDR Infiniband Switch I/O Module
- Cisco Catalyst Ethernet Switch I/O Modules
- Dell PowerConnect M6348 1 Gb Ethernet Switch I/O Module
- Dell PowerConnect M6220 Ethernet Switch I/O Module
- Dell PowerConnect M8024 10 Gb Ethernet Switch I/O Module
- Dell 8/4 Gbps FC SAN Module
- Brocade M5424 FC8 I/O Module
- I/O Modules—Pass-Through
- Installing Enclosure Components
- Troubleshooting The Enclosure
- Technical Specifications
- Getting help
Dell PowerEdge M1000e Enclosure Owner's Manual
Port Auto-Disablement in Quad-Port Network Daughter Card (Dell PowerEdge M710HD Only)
Systems installed
with quad-port Network Daughter Card support a Port Auto-Disablement
feature. This feature disables the third (NIC3) and fourth (NIC4)
ports of a quad-port network daughter card during system boot, if
the corresponding I/O module installed in the chassis Fabric A slots
does not support quad-port mapping. This behavior is limited to Fabric
A slots only and is automatically enabled or disabled depending on
the type of I/O module installed.
- NOTE: A quad-port network daughter card must be used with a 48-port switch module (32 internal ports) for all the ports to be active.
- NOTE: LOM firmware updates are applied only to the enabled ports on a quad-port network daughter card.
The following table provides an overview of the configurations that enable or disable the NIC3 and NIC4 ports of a quad-port network daughter card.
| IOM Slot A1 | IOM Slot A2 | NIC3 and NIC4 (Enabled/Disabled) | Port Auto-Disablement |
|---|---|---|---|
| Empty | Empty | Enabled | Inactive |
| Empty | Dual Port | Disabled | Active |
| Empty | Quad or Greater Port | Enabled | Inactive |
| Dual Port | Empty | Disabled | Active |
| Dual Port | Dual Port | Disabled | Active |
| Dual Port | Quad or Greater Port | Enabled | Inactive |
| Quad or Greater Port | Empty | Enabled | Inactive |
| Quad or Greater Port | Dual Port | Enabled | Inactive |
| Quad or Greater Port | Quad or Greater Port | Enabled | Inactive |
Proporcione valoraciones (1-5 estrellas).
Proporcione valoraciones (1-5 estrellas).
Proporcione valoraciones (1-5 estrellas).
Seleccione si el artículo le ha resultado útil o no.
Los comentarios no pueden contener caracteres especiales: <>()\