- Notes, cautions, and warnings
- Revision history
- Introduction
- VxRail network planning overview
- Plan the VxRail network
- VxRail cluster types
- VxRail hardware and switch selection decision points
- Prepare the data center to implement VxRail
- Decide on an IP address scheme
- Prepare external network connectivity for VxRail
- Prepare service connectivity for VxRail
- Prepare for VMware vSphere+ subscription licensing
- Prepare data center routing services
- Prepare for multirack VxRail cluster
- Prepare for VMware vSAN HCI mesh topology
- Prepare external FC storage for dynamic clusters
- Prepare for VxRail custom uplink assignments
- Prepare data center network MTU
- Prepare for LAG of VxRail networks
- Plan LAG on switch port pairs
- Prepare certificate authority server for VxRail
- Identify isolation IP addresses for VMware vSphere High Availability
- Plan the VxRail cluster implementation
- Decide on VxRail single point of management
- Decide on VxRail network traffic segmentation
- Decide on teaming and failover policies for VxRail networks
- Plan the VxRail logical network
- Plan network settings for VxRail management components
- Plan network settings for VMware vCenter Server management network
- Identify IP addresses for VxRail management components
- Select hostnames for VxRail management components
- Identify external applications and settings for VxRail
- Prepare the customer-managed VMware vCenter Server
- Prepare a customer-managed VMware VDS
- Reserve IP addresses for VxRail-managed VMware vSphere vMotion network
- Reserve IPv4/IPv6 addresses for VxRail vSAN network
- Decide on VxRail logging solution
- Assign passwords for VxRail management
- Plan VMware vSAN witness networking
- Plan networking for VxRail Satellite Nodes
- Configure the Network for VxRail
- Prepare to build the VxRail cluster
- VxRail network considerations after implementation
- Appendix A: VxRail Network Configuration Table
- Appendix B: VxRail Passwords
- Appendix C: VxRail cluster setup checklist
- Appendix D: VxRail Open Ports Requirements
- Appendix E: VMware VDS port group default settings
- Appendix F: Physical Network Switch Examples
- Pre-defined network profile: 2x10gb or 2x25gb from a single NDC/OCP
- Predefined network profile: 4x10gb or 4x25gb NDC/OCP
- Predefined network profile: 2 x 10/25 GB NDC/OCP and 2 x 10/25 GB PCIe
- Custom option: Any NDC/OCP ports paired with PCIe ports
- Custom option: Two NDC/OCP ports paired with PCIe ports other than the first slot
- Custom option: PCIe ports only
- Custom option: Six ports
- Custom option: Eight ports
- Custom option: Eight ports connected to four Ethernet switches
Dell VxRail Network Planning Guide
VxRail DPU options
DPUs support the offloading of network and security services from the main CPUs on the VxRail nodes.
The DPU is installed in the factory on the VxRail node instead of on a standard Ethernet adapter card. The DPU differs from a traditional Ethernet adapter card because VMware ESXio is installed on the device, and the DPU is configured with its own CPU.
The following guidelines apply for VxRail clusters with DPUs:
- The VxRail cluster must be running VxRail 8.0.010 or later.
- The VxRail nodes are configured in the factory with qualified and supported DPUs.
- The data center network supporting the VxRail cluster can support the physical network speed requirements of the DPU.
| Port speed | Vendor |
|---|---|
| 25 GbE |
|
| 100 GbE | Pensando |
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\