- Notes, cautions, and warnings
- Revision history
- Introduction
- VxRail network planning overview
- Plan the VxRail network
- VxRail cluster types
- VxRail hardware and switch selection decision points
- Prepare the data center to implement VxRail
- Decide on an IP address scheme
- Prepare external network connectivity for VxRail
- Prepare service connectivity for VxRail
- Prepare for VMware vSphere+ subscription licensing
- Prepare data center routing services
- Prepare for multirack VxRail cluster
- Prepare for VMware vSAN HCI mesh topology
- Prepare external FC storage for dynamic clusters
- Prepare for VxRail custom uplink assignments
- Prepare data center network MTU
- Prepare for LAG of VxRail networks
- Plan LAG on switch port pairs
- Prepare certificate authority server for VxRail
- Identify isolation IP addresses for VMware vSphere High Availability
- Plan the VxRail cluster implementation
- Decide on VxRail single point of management
- Decide on VxRail network traffic segmentation
- Decide on teaming and failover policies for VxRail networks
- Plan the VxRail logical network
- Plan network settings for VxRail management components
- Plan network settings for VMware vCenter Server management network
- Identify IP addresses for VxRail management components
- Select hostnames for VxRail management components
- Identify external applications and settings for VxRail
- Prepare the customer-managed VMware vCenter Server
- Prepare a customer-managed VMware VDS
- Reserve IP addresses for VxRail-managed VMware vSphere vMotion network
- Reserve IPv4/IPv6 addresses for VxRail vSAN network
- Decide on VxRail logging solution
- Assign passwords for VxRail management
- Plan VMware vSAN witness networking
- Plan networking for VxRail Satellite Nodes
- Configure the Network for VxRail
- Prepare to build the VxRail cluster
- VxRail network considerations after implementation
- Appendix A: VxRail Network Configuration Table
- Appendix B: VxRail Passwords
- Appendix C: VxRail cluster setup checklist
- Appendix D: VxRail Open Ports Requirements
- Appendix E: VMware VDS port group default settings
- Appendix F: Physical Network Switch Examples
- Pre-defined network profile: 2x10gb or 2x25gb from a single NDC/OCP
- Predefined network profile: 4x10gb or 4x25gb NDC/OCP
- Predefined network profile: 2 x 10/25 GB NDC/OCP and 2 x 10/25 GB PCIe
- Custom option: Any NDC/OCP ports paired with PCIe ports
- Custom option: Two NDC/OCP ports paired with PCIe ports other than the first slot
- Custom option: PCIe ports only
- Custom option: Six ports
- Custom option: Eight ports
- Custom option: Eight ports connected to four Ethernet switches
Dell VxRail Network Planning Guide
Plan network settings for VMware vCenter Server management network
For VxRail versions earlier than 7.0.350, the VxRail-managed VMware vCenter Server and VxRail Manager were placed on the same VxRail external management network with the VMware ESXi hosts, and a shared VLAN and subnet. For VxRail 7.0.350 and later, you can assign virtual appliances an IP address on a separate subnet and the subnet assigned a separate VLAN.
If you plan to deploy the virtual management components into a subnet that is separate from the VMware ESXi hosts, make a note of the network properties.
| Network configuration table | Action |
|---|---|
| Row 12 | Enter the VMware vCenter Server network IPv4 subnet mask. |
| Row 13 | Enter the VMware vCenter Server network IPv4 gateway. |
| Network configuration table | Action |
|---|---|
| Row 14 | Enter the VMware vCenter Server network IPv6 subnet mask. |
| Row 15 | Enter the VMware vCenter Server network IPv6 gateway. |
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\