- Notes, cautions, and warnings
- Revision history
- Introduction
- VxRail network planning overview
- Plan the VxRail network
- VxRail cluster types
- VxRail hardware and switch selection decision points
- Prepare the data center to implement VxRail
- Decide on an IP address scheme
- Prepare external network connectivity for VxRail
- Prepare service connectivity for VxRail
- Prepare for VMware vSphere+ subscription licensing
- Prepare data center routing services
- Prepare for multirack VxRail cluster
- Prepare for VMware vSAN HCI mesh topology
- Prepare external FC storage for dynamic clusters
- Prepare for VxRail custom uplink assignments
- Prepare data center network MTU
- Prepare for LAG of VxRail networks
- Plan LAG on switch port pairs
- Prepare certificate authority server for VxRail
- Identify isolation IP addresses for VMware vSphere High Availability
- Plan the VxRail cluster implementation
- Decide on VxRail single point of management
- Decide on VxRail network traffic segmentation
- Decide on teaming and failover policies for VxRail networks
- Plan the VxRail logical network
- Plan network settings for VxRail management components
- Plan network settings for VMware vCenter Server management network
- Identify IP addresses for VxRail management components
- Select hostnames for VxRail management components
- Identify external applications and settings for VxRail
- Prepare the customer-managed VMware vCenter Server
- Prepare a customer-managed VMware VDS
- Reserve IP addresses for VxRail-managed VMware vSphere vMotion network
- Reserve IPv4/IPv6 addresses for VxRail vSAN network
- Decide on VxRail logging solution
- Assign passwords for VxRail management
- Plan VMware vSAN witness networking
- Plan networking for VxRail Satellite Nodes
- Configure the Network for VxRail
- Prepare to build the VxRail cluster
- VxRail network considerations after implementation
- Appendix A: VxRail Network Configuration Table
- Appendix B: VxRail Passwords
- Appendix C: VxRail cluster setup checklist
- Appendix D: VxRail Open Ports Requirements
- Appendix E: VMware VDS port group default settings
- Appendix F: Physical Network Switch Examples
- Pre-defined network profile: 2x10gb or 2x25gb from a single NDC/OCP
- Predefined network profile: 4x10gb or 4x25gb NDC/OCP
- Predefined network profile: 2 x 10/25 GB NDC/OCP and 2 x 10/25 GB PCIe
- Custom option: Any NDC/OCP ports paired with PCIe ports
- Custom option: Two NDC/OCP ports paired with PCIe ports other than the first slot
- Custom option: PCIe ports only
- Custom option: Six ports
- Custom option: Eight ports
- Custom option: Eight ports connected to four Ethernet switches
Dell VxRail Network Planning Guide
Storage network considerations
Consider the additional feature requirements while selecting Ethernet switches for your VxRail cluster depending on interoperability requirements for different types of storage resources.
If your VxRail cluster includes adapters that support RoCE (RDMA over Converged Ethernet) for VMware vSAN storage connectivity, the supporting network must support a lossless transport. A lossless network is defined as one where no frames are dropped because of network congestion.
- Select switches that support Data Center Bridging (DCB). The Data Center Bridging feature supports the elimination of packet loss due to buffer or queue overflow.
- The DCB must support bandwidth allocation based on priority settings, which are known as Class of Service (CoS).
- Priority Flow Control (PFC) is required on the switches to provide RoCE traffic a higher priority than other network traffic.
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\