- Notes, cautions, and warnings
- Revision history
- Introduction
- VxRail network planning overview
- Plan the VxRail network
- VxRail cluster types
- VxRail hardware and switch selection decision points
- Prepare the data center to implement VxRail
- Decide on an IP address scheme
- Prepare external network connectivity for VxRail
- Prepare service connectivity for VxRail
- Prepare for VMware vSphere+ subscription licensing
- Prepare data center routing services
- Prepare for multirack VxRail cluster
- Prepare for VMware vSAN HCI mesh topology
- Prepare external FC storage for dynamic clusters
- Prepare for VxRail custom uplink assignments
- Prepare data center network MTU
- Prepare for LAG of VxRail networks
- Plan LAG on switch port pairs
- Prepare certificate authority server for VxRail
- Identify isolation IP addresses for VMware vSphere High Availability
- Plan the VxRail cluster implementation
- Decide on VxRail single point of management
- Decide on VxRail network traffic segmentation
- Decide on teaming and failover policies for VxRail networks
- Plan the VxRail logical network
- Plan network settings for VxRail management components
- Plan network settings for VMware vCenter Server management network
- Identify IP addresses for VxRail management components
- Select hostnames for VxRail management components
- Identify external applications and settings for VxRail
- Prepare the customer-managed VMware vCenter Server
- Prepare a customer-managed VMware VDS
- Reserve IP addresses for VxRail-managed VMware vSphere vMotion network
- Reserve IPv4/IPv6 addresses for VxRail vSAN network
- Decide on VxRail logging solution
- Assign passwords for VxRail management
- Plan VMware vSAN witness networking
- Plan networking for VxRail Satellite Nodes
- Configure the Network for VxRail
- Prepare to build the VxRail cluster
- VxRail network considerations after implementation
- Appendix A: VxRail Network Configuration Table
- Appendix B: VxRail Passwords
- Appendix C: VxRail cluster setup checklist
- Appendix D: VxRail Open Ports Requirements
- Appendix E: VMware VDS port group default settings
- Appendix F: Physical Network Switch Examples
- Pre-defined network profile: 2x10gb or 2x25gb from a single NDC/OCP
- Predefined network profile: 4x10gb or 4x25gb NDC/OCP
- Predefined network profile: 2 x 10/25 GB NDC/OCP and 2 x 10/25 GB PCIe
- Custom option: Any NDC/OCP ports paired with PCIe ports
- Custom option: Two NDC/OCP ports paired with PCIe ports other than the first slot
- Custom option: PCIe ports only
- Custom option: Six ports
- Custom option: Eight ports
- Custom option: Eight ports connected to four Ethernet switches
Dell VxRail Network Planning Guide
IP-based storage options
If the data center does not support FC storage, shared VMware vSAN resources or a deployed PowerFlex storage array, you can have storage over an IP network.
The supported storage resources can be either block-based or file system based. With block-level storage option, the LUN is presented to the VxRail cluster nodes over an IP network. VMware vSphere is used to configure a VMFS data store from the LUN.
iSCSI is a standard feature in VMware vSphere supported with VxRail. iSCSI is enabled by configuring a software adapter on a NIC on the VxRail nodes. The adapter then serves as an iSCSI initiator by targeting external storage arrays to present LUNs back to the initiators.
The NFS option also works over an IP network, except the storage presented back to the VxRail cluster is from a compatible file server, and the storage format is file-based instead of block-based. With this option, the external file system is mounted by the VxRail nodes to enable access over the IP network, and configured to serve as a data store.
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\