SCv2080 Storage System Owner’s Manual

PDF

SCv2080 Storage SystemStorage Controller with Fibre Channel Front-End Ports

The following figures show the features and indicators on a storage controller with Fibre Channel front-end ports.

8 Gb Fibre Channel storage controller features and indicators — Figure 1. SCv2080 Storage SystemStorage Controller with Four 8 Gb Fibre Channel Front-End Ports

16 Gb Fibre Channel storage controller features and indicators — Figure 2. SCv2080 Storage SystemStorage Controller with Two 16 Gb Fibre Channel Front-End Ports

Features and indicators on the SCv2080storage controller.
Item	Control/Feature	Icon	Description
1	Battery status indicator		Blinking green (on 0.5 sec. / off 1.5 sec.) – Battery heartbeat Fast blinking green (on 0.5 sec. / off 0.5 sec.) – Battery is charging Steady green – Battery is ready
2	Battery fault indicator		Off – No faults Blinking amber – Correctable fault detected Steady amber – Uncorrectable fault detected; replace battery
3	MGMT port (Slot 3/Port 1)	—	Ethernet/iSCSI port that is typically used for storage system management and access to the BMC NOTE To use the MGMT port as an iSCSI port for replication to another Storage Center, a Flex Port license and replication license are required. To use the MGMT port as a front-end connection to host servers, a Flex Port license is required.
4	REPL port (Slot 3/Port 2)	—	Ethernet/iSCSI port that is typically used for replication to another Storage Center (requires a replication license) NOTE To use the RELP port as a front-end connection to host servers, a Flex Port license is required.
5	SAS activity indicators	—	There are four SAS PHYs per SAS port. Off – SAS PHY is not connected Steady green – SAS PHY is connected, but not active Blinking green – SAS PHY is not connected nor active
6	Storage controller status		On – Storage controller completed a power-on self-test (POST)
7	Recessed power off button		Not currently used
8	Storage controller fault		Off – No faults Steady amber – Firmware has detected an error Blinking amber – Storage controller is performing a POST
9	Recessed reset button		Not currently used
10	Identification LED		Off – Identification disabled Blinking blue (for 15 sec.) – Identification is enabled Blinking blue (continuously) – Storage controller shut down to the Advanced Configuration and Power Interface (ACPI) S5 state
11	USB port		One USB 3.0 connector
12	Diagnostic LEDs (8)	—	Green LEDs 0–3 – Low byte hex POST code Green LEDs 4–7 – High byte hex POST code
13	Serial port (3.5 mm mini jack)		Not for customer use
14	Two options: Four Fibre Channel ports (Slot 1/Port 1, Slot 1/Port 2, Slot 1/Port 3, and Slot 1/Port 4) with three LEDs per port Two Fibre Channel ports (Slot 1/Port 1 and Slot 1/Port 2) with three LEDs per port	—	LEDs for the four 8 Gb Fibre Channel ports: All off – No power All on – Booting up Blinking amber – 2 Gbps activity Blinking green – 4 Gbps activity Blinking yellow – 8 Gbps activity Blinking amber and yellow – Beacon All blinking (simultaneous) – Firmware initialized All blinking (alternating) – Firmware fault LEDs for the two 16 Gb Fibre Channel ports: All off – No power All on – Booting up Blinking amber – 4 Gbps activity Blinking green – 8 Gbps activity Blinking yellow – 16 Gbps activity Blinking amber and yellow – Beacon All blinking (simultaneous) – Firmware initialized All blinking (alternating) – Firmware fault
15	Mini-SAS port B (Slot 2/Port 2)		Back-end expansion port B
16	Mini-SAS port A (Slot 2/Port 1)		Back-end expansion port A