1 | Battery status indicator | ![Battery status](https://dl.dell.com/content/guides/public/Html/scv2080om/images/GUID-32099623-F733-4328-A98B-799A58769C6B-low.jpg) | - Blinking green (on 0.5 sec. / off 1.5 sec.) – Battery
heartbeat
- Fast blinking green (on 0.5 sec. / off 0.5 sec.) –
Battery is charging
- Steady green – Battery is ready
|
2 | Battery fault indicator | ![Battery fault](https://dl.dell.com/content/guides/public/Html/scv2080om/images/GUID-74FFB61F-4801-4C97-809A-1F5CD68ADED6-low.jpg) | - Off – No faults
- Blinking amber – Correctable fault detected
- Steady amber – Uncorrectable fault detected; replace
battery
|
3 | MGMT port (Slot 3/Port 1) | — | Ethernet/iSCSI port that is typically used for storage system management and
access to the BMC NOTE To use the MGMT port as an iSCSI port for replication to another Storage Center, a Flex Port license
and replication license are required. To use the MGMT port as a front-end
connection to host servers, a Flex Port license is required. |
4 | REPL port (Slot 3/Port 2) | — | Ethernet/iSCSI port that is typically used for
replication to another Storage Center NOTE To use the RELP
port as a front-end connection to host servers, a Flex Port license
is required. |
5 | SAS activity indicators | — | There are four SAS PHYs per SAS port.- Off – SAS PHY is not connected
- Steady green – SAS PHY is connected, but not active
- Blinking green – SAS PHY is not connected nor active
|
6 | Storage controller module status | ![Storage controller module status](https://dl.dell.com/content/guides/public/Html/scv2080om/images/GUID-32099623-F733-4328-A98B-799A58769C6B-low.jpg) | On – Storage controller completed a power-on self-test (POST) |
7 | Recessed power off button | ![Power off button](https://dl.dell.com/content/guides/public/Html/scv2080om/images/GUID-6F15C288-C9D6-46E5-8F06-AC7FCE825FDA-low.jpg) | Not currently used |
8 | Storage controller module fault | ![Storage controller module fault](https://dl.dell.com/content/guides/public/Html/scv2080om/images/GUID-74FFB61F-4801-4C97-809A-1F5CD68ADED6-low.jpg) | - Off – No faults
- Steady amber – Firmware has detected an error
- Blinking amber – Storage controller is
performing a POST
|
9 | Recessed reset button | ![Reset button](https://dl.dell.com/content/guides/public/Html/scv2080om/images/GUID-AED66FE0-8E48-4C45-A120-9C56DB36303F-low.jpg) | Not currently used |
10 | Identification LED | ![Identification LED](https://dl.dell.com/content/guides/public/Html/scv2080om/images/GUID-F9B85BE2-2EC5-4E4B-B489-1C1C41A11F2B-low.jpg) | - Off – Identification disabled
- Blinking blue (for 15 sec.) – Identification is enabled
- Blinking blue (continuously) – Storage controller shut
down to the Advanced Configuration and Power Interface (ACPI) S5 state
|
11 | USB port | ![USB port](https://dl.dell.com/content/guides/public/Html/scv2080om/images/GUID-A6CBAC00-0DCF-4A73-9A0F-2CF4C1F67A04-low.jpg) | One USB 3.0 connector |
12 | Diagnostic LEDs (8) | — | - Green LEDs 0–3 – Low byte hex POST code
- Green LEDs 4–7 – High byte hex POST code
|
13 | Serial port (3.5 mm mini jack) | ![Serial port](https://dl.dell.com/content/guides/public/Html/scv2080om/images/GUID-214FB71E-FF28-4E00-9AA5-2F69D656B593-low.jpg) | Not for customer use |
14 | Four Mini-SAS High Density (HD) ports (Slot 1/Port
1, Slot 1/Port 2, Slot 1/Port 3, and Slot 1/Port 4) | — | Front-end connectivity ports NOTE The mini-SAS HD ports
are used for front-end connectivity only and cannot be used for back-end
expansion. |
15 | Mini-SAS port B (Slot 2/Port 2) | ![Mini SAS port](https://dl.dell.com/content/guides/public/Html/scv2080om/images/GUID-A24ECC3E-B84F-41C2-89FF-77096506DE24-low.jpg) | Back-end expansion port B |
16 | Mini-SAS port A (Slot 2/Port 1) | ![Mini SAS port](https://dl.dell.com/content/guides/public/Html/scv2080om/images/GUID-A24ECC3E-B84F-41C2-89FF-77096506DE24-low.jpg) | Back-end expansion port A |