- Notes, cautions, and warnings
- Introduction
- Revision history
- Initial configuration and setup
- Performing common tasks
- Displaying system information at a glance
- Managing block storage
- Protection domains
- Fault sets
- Storage data servers
- Storage pools
- Acceleration pools
- Devices
- Volumes
- NVMe targets
- Hosts
- Managing file storage
- Overview of configuring NAS servers
- About file system storage
- File protection
- Create a protection policy
- Create snapshot rules
- Create a snapshot
- Assign a protection policy to a file system
- Unassign a protection policy
- Modify a protection policy
- Delete a protection policy
- Modify a snapshot rule
- Delete a snapshot rule
- Refresh a file system using snapshot
- Restore a file system from a snapshot
- Protecting a block storage environment
- Snapshots
- Create snapshots
- Overwrite volume content from a snapshot
- Set bandwidth and IOPS limits for snapshots
- Lock and unlock snapshots
- Delete snapshots
- Map snapshots
- Unmap snapshots
- Increase the size of a snapshot
- Migrate a snapshot vTree
- Pause snapshot vTree migration
- Roll back snapshot vTree migration
- Set snapshot vTree migration priority
- Snapshot policies
- Remote protection
- Extract and upload certificates
- Journal capacity
- Add a peer system
- Restart the replication cluster
- SDRs
- Replication consistency group
- Replication direction and mapping
- Create an RCG
- Map RCG target volumes to hosts
- Unmap a host from RCG target volumes
- Set the target to inconsistent mode
- Set the target to consistent mode
- Modify RPO
- Add a replication pair to an RCG
- Pause replication for an RCG
- Resume replication for an RCG
- Create a snapshot of an RCG volume
- Add an RCG snapshot policy
- Perform a failover
- Reverse replication
- Restore replication
- Test Failover
- Stop a failover test
- Freeze an RCG
- Unfreeze an RCG
- Activate an RCG
- Terminate replication in an RCG
- Delete an RCG
- Pause creation of an initial copy
- Resume creation of initial copy
- Set copying priority
- Unpair from RCG
- Snapshots
- Performing lifecycle operations for a resource group
- Deploying a resource configuration in a resource group
- Basic tasks
- Deploying a resource group
- Adding an existing resource group
- Updating a resource group with new firmware and software
- Viewing a compliance report
- Entering and exiting service mode
- Replacing a drive
- Replacing NVDIMM node or battery
- Reconfiguring MDM roles
- Migrating vCLS VMs to shared storage
- Adding components to a resource group
- Resize a volume
- Removing resources from a resource group
- Adding NVMe/TCP storage access
- Additional resource group management tasks
- Basic tasks
- Preparing a template for a resource group deployment
- Basic tasks
- Additional template management tasks
- Deploying a resource configuration in a resource group
- Managing resources
- Basic tasks
- Additional resource management tasks
- Monitoring events and alerts
- Configuring system settings
- User management
- Repositories
- Getting started
- Networking
- Events and alerts
- License management
- Security
- Serviceability
- Software upgrade
- PowerFlex Manager user interface reference
- Additional administration activities
- Retrieving logs for the PowerFlex nodes
- Retrieving logs for PowerFlex components
- Retrieving additional PowerFlex logs
- Enabling audit logging
- Managing storage devices using CloudLink
- Understanding NVMe over TCP load balancing
- Managing NAS server configuration
- Migrating to NVMe/TCP on ESXi
Dell PowerFlex 4.5.x Administration Guide
Managing templates
On the
Templates page, you can view information about templates in a list or tile view. To switch between views, click the tile icon
or list icon
at the top of the
Templates page. When in tile view, you can view the templates under a category by clicking the graphic that represents the category.
Users with standard permissions can view details of only those templates for which the administrator has granted permission.
Templates - My Templates List View
The My Templates page displays the details of the templates that you have created.
| Field | Description |
|---|---|
| + Add a Template | Allows you to add a template. After you add a template, you can add node, cluster, and VM components on the template builder page. |
| Export All | Allows you to export all templates to a CSV file. |
| Filter By | Allows you to filter and view templates based on the template category. |
| State | Displays the state of the template - Draft or Published. |
| Category | Displays the template category. |
| Name | Displays the template name. |
| Last Deployed On | Displays the date when the template was last deployed. |
| Components | Displays the components in the template. |
Templates - Sample Templates
The Sample Templates page displays the default templates that you can use in your environment.
| Field | Description |
|---|---|
| Name | Displays the template name. |
| Components | Displays the components in the template. |
On the Templates page, the right pane displays the name of the template, icons of components in the template, and the following details for a selected template:
| Field | Description |
|---|---|
| Edit | Click to edit the template. |
| Delete | Click to delete the template. |
| View Details | Click to view the details of the template, such as components in the template. |
| Clone | Click to clone the template. |
| Export Template | Click to export the template to a GPG file. You can use the exported template to duplicate the settings. |
| Created On | Displays the date and time when the template was created. |
| Created By | Displays the name of the user who created the template. |
| Updated On | Displays the date and time when the template was updated. |
| Updated By | Displays the name of the user who updated the template. |
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\