- Notes, cautions, and warnings
- Introduction
- Automated Upgrade
- Automated Upgrade of Linux-based Nodes
- Automated Upgrade of ESXi-based Nodes
- Upgrading ESXi-based configurations
- Download installation packages
- Preparing to upgrade ESXi configurations
- Upgrade the PowerFlex Gateway with Stateless ESXi IP addresses
- Upgrading PowerFlex—ESXi-based nodes
- Upgrade the PowerFlex presentation server (PowerFlex GUI) from v3.5 or later
- Upgrade the PowerFlex GUI from versions earlier than v3.5
- After upgrading an ESXi-based system
- Automated Upgrade of Nodes in a Two-Layer Configuration
- Preparing to upgrade two-layer configuration—Linux and ESX-based
- Upgrading two-layer configurations (Linux-based and ESX-based)
- Upgrade the PowerFlex presentation server (PowerFlex GUI) from v3.5 or later
- Upgrade the PowerFlex GUI from versions earlier than v3.5
- Prepare server operating systems for support of large-scale systems (up to 2048 SDCs)
- After upgrading a two-layer system
- Manual Upgrade
- Manual Upgrade of Linux-based Nodes
- Manual upgrade of physical Linux-based configurations
- Non-default certificate use before and after a PowerFlex Gateway upgrade
- Upgrade the PowerFlex GUI from versions earlier than v3.5
- Upgrade the PowerFlex presentation server (PowerFlex GUI) from v3.5 or later
- Manual upgrade of Linux-based nodes—3-node MDM cluster
- Manual upgrade of Linux-based nodes—5-node MDM cluster
- Prepare server operating systems for support of large-scale systems (up to 2048 SDCs)
- Manual Upgrades in the ESXi Environment
- Manually upgrade an ESXi-based PowerFlex system
- Collect and record PowerFlex information
- Prerequisites for manual upgrades in ESXi environments
- Upgrade the PowerFlex GUI from versions earlier than v3.5
- Upgrade the PowerFlex presentation server (PowerFlex GUI) from v3.5 or later
- Unregister the old PowerFlex system
- Unregister the current PowerFlex plug-in
- Register the new PowerFlex plug-in
- PowerFlex component overview
- Upgrade the PowerFlex system
- Upgrade the SDC on an ESXi host
- Upgrade the CentOS operating system on SVMs
- Upgrade the PowerFlex Gateway operating system
- After upgrading an ESXi system
- Miscellaneous topics for manual upgrades in ESXi environments
- Manually upgrade an ESXi-based PowerFlex system
- Manual Upgrade of Linux-based Nodes
- Firmware Upgrade
- Upgrade of LSI RAID Controller Firmware and Driver
- VxFlex Ready Node Server Firmware Upgrades
- Reference Topics
- Post-Upgrade and Other Common Tasks
- Shutdown or restart a node gracefully
- Disabling IPMI
- Check NVDIMM capacity compatibility for future upgrades
- Configure the SDS for NVDIMM health awareness
- Extracting PowerFlex packages
- Upgrading the PowerFlex Gateway when a custom certificate is used
- Troubleshoot PowerFlex plug-in registration issues
- Unregister the PowerFlex plug-in
- Register the PowerFlex plug-in manually
- Store Tomcat's keystore password in the lockbox
- Prepare lockbox files for Java upgrade
- Updating the SDC parameters
- Switching to secured authentication mode
- Configure Secure Remote Services or email notifications after upgrading
- Upgrade a VMware-based PowerFlex system that contains CloudLink-encrypted devices
- Manually upgrade an ESXi-based PowerFlex system with CloudLink
- Collect and record PowerFlex information
- Prerequisites for manual upgrades in ESXi environments
- Upgrade the PowerFlex GUI from versions earlier than v3.5
- Upgrade the PowerFlex GUI from v3.5 or later
- Unregister the old PowerFlex system
- Unregister the current PowerFlex plug-in
- Register the new PowerFlex plug-in
- PowerFlex component upgrade overview
- Upgrade the PowerFlex system
- Upgrade the SDC on an ESXi host
- Upgrade the CentOS operating system on SVMs
- Upgrade the PowerFlex Gateway operating system
- Upgrade CloudLink
- After upgrading an ESXi system
- Manually upgrade an ESXi-based PowerFlex system with CloudLink
- Upgrade the operating system to a major ESXi version
- DTK - Hardware Update Bootable ISO
- Dell OpenManage DRAC Tools (RACADM)
- Update the SATADOM firmware (VxFlex Ready Node R630/R730xd only)
- Recommended BIOS and firmware settings
- Troubleshooting the Hardware ISO
- Additional resources
- Set up the iDRAC IP address and BIOS
- Verify the status of the system hardware, storage controller, and disks - R630/R730xd servers
- Verify the status of the system hardware, storage controller, and disks - R640/R740xd servers
- Increasing SVM system disk size
- Upgrading systems with more than 512 SDCs, and configuring LIA LDAP in large systems
- Post-Upgrade and Other Common Tasks
Upgrade Dell PowerFlex to v3.6.x
Automated upgrade of physical Linux-based configurations
Upgrade PowerFlex in an automated process, when all components reside on physical Linux-based nodes.
Physical machine upgrades use the
PowerFlex Installer (part of the
PowerFlex Gateway), together with the LIA, to orchestrate the upgrade.
NOTE:To verify if LIA is installed, or to add LIA to a system where it is not installed, see "Add LIA to a system to enable automated maintenance and upgrades" in the
Configure and Customize Dell PowerFlex.
Upgrades are non-disruptive; upgrades can be performed while I/Os are running and volumes are mapped.
The
PowerFlex Installer can be used to upgrade MDM clusters from a 3-node cluster to a 3-node cluster, or from a 5-node to a 5-node cluster. Extension of a 3-node MDM cluster to a 5-node MDM cluster can be performed after the system upgrade. For more information, see "Extend an existing
PowerFlex system" in the
Configure and Customize Dell PowerFlex.
NOTE:Automated upgrades are not supported on systems managed by a single-node MDM cluster.
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\