NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 1. 12 x 3.5-inch SAS/SATA with APERC11/12 in Riser 2 This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
CTRL_SRC_SA1_PA1 (adapter PERC controller connector)
BP_DST_SA1 (backplane signal connector)
3
CTRL_SRC_SB1_PB1 (adapter PERC controller connector)
BP_DST_SB1 (backplane signal connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 2. 12 x 3.5-inch SAS/SATA + 2 x 2.5-inch SAS/SATA with APERC11/12 in Riser 2This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
CTRL_SRC_SB1_PB1 (adapter PERC controller connector) and BP_DST_SB1 (backplane signal connector)
BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
3
CTRL_SRC_SA1_PA1 (adapter PERC controller connector)
BP_DST_SA1 (backplane signal connector)
4
SIG_PWR_0 (system board power connector)
BP_PWR_1 (rear backplane power connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 3. 12 x 3.5-inch SAS/SATA + 2 x 2.5-inch NVMe with APERC11/12 in Riser 2This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
CTRL_SRC_SB1_PB1 (adapter PERC controller connector)
BP_DST_SB1 (backplane signal connector)
3
CTRL_SRC_SA1_PA1 (adapter PERC controller connector)
BP_DST_SA1 (backplane signal connector)
4
SIG_PWR_0 (system board power connector)
BP_PWR_1 (rear backplane power connector)
5
SL11_CPU1_PB7 (signal connector on system board)
BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 4. 12 x 3.5-inch SAS/SATA + 4 x 2.5-inch SAS/SATA with APERC11/12 in Riser 2 This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
CTRL_SRC_SB1_PB1 (adapter PERC controller connector) and BP_DST_SB1 (backplane signal connector)
BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
3
CTRL_SRC_SA1_PA1 (adapter PERC controller connector)
BP_DST_SA1 (backplane signal connector)
4
SIG_PWR_0 (system board power connector)
BP_PWR_1 (rear backplane power connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 5. 12 x 3.5-inch SAS/SATA + 4 x 2.5-inch NVMe with APERC11/12 in Riser 2This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
SIG_PWR_0 (system board power connector)
BP_PWR_1 (rear backplane power connector)
3
SL4_CPU1_PA2 (signal connector on system board)
BP_DST_PA1 (rear backplane signal connector) and BP_DST_PB1 (rear backplane signal connector)
4
SL11_CPU1_PB7 (signal connector on system board)
BP_DST_PA2 (rear backplane signal connector) and BP_DST_PB2 (rear backplane signal connector)
5
CTRL_SRC_SB1_PB1 (adapter PERC controller connector)
BP_DST_SB1 (backplane signal connector)
6
CTRL_SRC_SA1_PA1 (adapter PERC controller connector)
BP_DST_SA1 (backplane signal connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 6. 8 x 2.5-inch NVMe This table shows connector information.
Order
From
To
1
SL1_CPU2_PA1 (signal connector on system board)
BP_DST_PA1 (backplane signal connector)
2
SL2_CPU2_PB1 (signal connector on system board)
BP_DST_PB1 (backplane signal connector)
3
SL3_CPU1_PA2 (signal connector on system board) and SL4_CPU1_PB2 (signal connector on system board)
BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
4
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 7. 8 x 2.5-inch NVMe RAID with fPERC (H755N)This table shows connector information.
Order
From
To
1
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
2
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
3
CTRL_SRC_PB1 (fPERC controller connector)
BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
4
CTRL_SRC_PA1 (fPERC controller connector)
BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
NOTE:An 8 x 2.5-inch NVMe backplane with fPERC H755 should be assembled outside and inserted into the system, along with all necessary cables.
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 8. 8 x 2.5-inch NVMe RAID with fPERC (H965i)This table shows connector information.
Order
From
To
1
SL4_CPU1_PB2 (signal connector on system board)
CTRL_DST_PB1 (fPERC input connector)
2
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
4
CTRL_SRC_PB1 (fPERC controller connector)
BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
5
CTRL_SRC_PA1 (fPERC controller connector)
BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
NOTE:An 8 x 2.5-inch NVMe backplane with fPERC H965i should be assembled outside and inserted into the system, along with all necessary cables.
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 9. 8 x 2.5-inch Universal (SAS/SATA/NVMe) with fPERC (HBA355i, H355, H755)This table shows connector information.
Order
From
To
1
SL5_CPU2_PB3 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
2
SL3_CPU1_PA2 (signal connector on system board) and SL4_CPU1_PB2 (signal connector on system board)
BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
3
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
4
SL2_CPU2_PB1 (signal connector on system board)
CTRL_DST_PB1 (fPERC input connector)
5
SL1_CPU2_PA1 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 10. 16 x 2.5-inch NVMe RAID with fPERC (H755N)This table shows connector information.
Order
From
To
1
SL1_CPU2_PA1 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
2
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
3
CTRL_SRC_PB1 (fPERC controller connector)
BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
4
CTRL_SRC_PA1 (fPERC controller connector)
BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
5
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
6
SIG_PWR_2 (system board power connector)
BP_PWR_1 (backplane power connector)
7
CTRL_SRC_PB1 (fPERC controller connector)
BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
8
CTRL_SRC_PA1 (fPERC controller connector)
BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
NOTE:An 8 x 2.5-inch NVMe backplanes with fPERC H755 should be assembled outside and inserted into the system, along with all necessary cables.
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 11. 16 x 2.5-inch NVMe This table shows connector information.
Order
From
To
1
SL2_CPU2_PA1 (signal connector on system board)
BP_DST_PA1 (backplane signal connector)
2
SL1_CPU2_PB1 (signal connector on system board)
BP_DST_PB1 (backplane signal connector)
3
SL5_CPU2_PB3 (signal connector on system board)
BP_DST_PA2 (backplane signal connector)
4
SL6_CPU2_PA3 (signal connector on system board)
BP_DST_PB2 (backplane signal connector)
5
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
6
SL3_CPU1_PA2 (signal connector on system board)
BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
7
SL4_CPU1_PB2 (signal connector on system board)
BP_DST_PB1 (backplane signal connector)
8
SL7_CPU1_PB4 (signal connector on system board)
BP_DST_PA2 (backplane signal connector)
9
SIG_PWR_2 (system board power connector)
BP_PWR_1 (backplane power connector)
10
SL8_CPU1_PA4 (signal connector on system board)
BP_DST_PB2 (backplane signal connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 12. 16 x 2.5-inch NVMe RAID with fPERC (H965i)This table shows connector information.
Order
From
To
1
SL1_CPU2_PB1 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
2
SL2_CPU2_PA1 (signal connector on system board)
CTRL_DST_PB1 (fPERC input connector)
3
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
4
CTRL_SRC_PB1 (fPERC controller connector)
BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
5
CTRL_SRC_PA1 (fPERC controller connector)
BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
6
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
7
SL4_CPU1_PB2 (signal connector on system board)
CTRL_DST_PB1 (fPERC input connector)
8
SIG_PWR_2 (system board power connector)
BP_PWR_1 (backplane power connector)
9
CTRL_SRC_PB1 (fPERC controller connector)
BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
10
CTRL_SRC_PA1 (fPERC controller connector)
BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
NOTE:An 8 x 2.5-inch NVMe backplanes with fPERC H965i should be assembled outside and inserted into the system, along with all necessary cables.
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 13. 16 x 2.5-inch SAS/SATA with fPERC (HBA355i, H355, H755)This table shows connector information.
Order
From
To
1
SL3_CPU1_PA2 (signal connector on system board)
CTRL_SRC_PA1 (fPERC controller connector)
2
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
3
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SA1 (backplane signal connector)
4
SIG_PWR_2 (system board power connector)
BP_PWR_1 (backplane power connector)
Table 14. 16 x 2.5-inch SAS/SATA with fPERC (H965i)This table shows connector information.
Order
From
To
1
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
2
SL4_CPU1_PB2 (signal connector on system board)
CTRL_DST_PB1 (fPERC input connector)
3
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
4
CTRL_SRC_SA1 (fPERC controller connector)
BP_DST_SA1 (backplane signal connector)
5
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SA1 (backplane signal connector)
6
SIG_PWR_2 (system board power connector)
BP_PWR_1 (backplane power connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 15. 16 x 2.5-inch SAS/SATA + 8 x 2.5-inch NVMe with fPERC (HBA355i, H355, H755)This table shows connector information.
Order
From
To
1
SL1_CPU2_PB1 (signal connector on system board) and SL2_CPU2_PA1 (signal connector on system board)
BP_DST_PB1 (backplane signal connector) and BP_DST_PA1 (backplane signal connector)
2
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
3
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
4
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SA1 (backplane signal connector)
5
SIG_PWR_2 (system board power connector)
BP_PWR_1 (backplane power connector)
6
SL4_CPU1_PB2 (signal connector on system board)
CTRL_DST_PA2 (fPERC input connector)
7
SL7_CPU1_PB4 (signal connector on system board)
CTRL_DST_PB2 (fPERC input connector)
8
SIG_PWR_0 (system board power connector)
BP_PWR_1 (backplane power connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 16. 16 x 2.5-inch SAS/SATA + 8 x 2.5-inch NVMe with fPERC (H965i)This table shows connector information.
Order
From
To
1
SL1_CPU2_PB1 (signal connector on system board) and SL2_CPU2_PA1 (signal connector on system board)
BP_DST_PB1 (backplane signal connector) and BP_DST_PA1 (backplane signal connector)
2
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
3
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
4
SL4_CPU1_PB2 (signal connector on system board)
CTRL_DST_PB1 (fPERC input connector)
5
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SA1 (backplane signal connector)
6
CTRL_SRC_SA1 (fPERC controller connector)
BP_DST_SA1 (backplane signal connector)
7
SIG_PWR_2 (system board power connector)
BP_PWR_1 (backplane power connector)
8
SL7_CPU1_PB4 (signal connector on system board)
BP_DST_PA2 (backplane signal connector)
9
SIG_PWR_0 (system board power connector)
BP_PWR_1 (backplane power connector)
10
SL8_CPU1_PA4 (signal connector on system board)
BP_DST_BA2 (backplane signal connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 17. 16 x 2.5-inch SAS/SATA + 8 x 2.5-inch NVMe with fPERC (HBA355i, H355, H755)This table shows connector information.
Order
From
To
1
SL1_CPU2_PA1 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
2
SL5_CPU2_PB3 (signal connector on system board)
BP_DST_PA1 (backplane signal connector)
3
SL6_CPU2_PA3 (signal connector on system board)
BP_DST_PB1 (backplane signal connector)
4
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
5
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SA1 (backplane signal connector)
6
SL3_CPU1_PA2 (signal connector on system board)
BP_DST_PA2 (backplane signal connector)
7
SL4_CPU1_PB2 (signal connector on system board)
BP_DST_PB2 (backplane signal connector)
8
SIG_PWR_2 (system board power connector)
BP_PWR_1 (backplane power connector)
9
SIG_PWR_0 (system board power connector)
BP_PWR_1 (backplane power connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 18. 16 x 2.5-inch SAS/SATA + 8 x 2.5-inch NVMe with fPERC (H965i)This table shows connector information.
Order
From
To
1
SL1_CPU2_PA1 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
2
SL2_CPU2_PB1 (signal connector on system board)
CTRL_DST_PB1 (fPERC input connector)
3
SL5_CPU2_PB3 (signal connector on system board)
BP_DST_PA1 (backplane signal connector)
4
SL6_CPU2_PA3 (signal connector on system board)
BP_DST_PB1 (backplane signal connector)
5
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
6
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SA1 (backplane signal connector)
7
CTRL_SRC_SA1 (fPERC controller connector)
BP_DST_SA1 (backplane signal connector)
8
SL3_CPU1_PA2 (signal connector on system board)
BP_DST_PA2 (backplane signal connector)
9
SL4_CPU1_PB2 (signal connector on system board)
BP_DST_PB2 (backplane signal connector)
10
SIG_PWR_2 (system board power connector)
BP_PWR_1 (backplane power connector)
11
SIG_PWR_0 (system board power connector)
BP_PWR_1 (backplane power connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 19. 24 x 2.5-inch SAS/SATA with 8 universal (SAS/SATA/NVMe) slots and fPERC (H965i)This table shows connector information.
Order
From
To
1
SL1_CPU2_PA1 (signal connector on system board) and SL2_CPU2_PB1 (signal connector on system board)
BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
2
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
3
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
4
SL4_CPU1_PB2 (signal connector on system board)
CTRL_DST_PB1 (fPERC input connector)
5
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SB1 (backplane expander signal connector)
6
CTRL_SRC_SA1 (fPERC controller connector)
BP_DST_SA1 (backplane expander signal connector)
7
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
8
SL7_CPU1_PB4 (signal connector on system board)
BP_DST_PA2 (backplane signal connector)
9
SL8_CPU1_PA4 (signal connector on system board)
BP_DST_PB2 (backplane signal connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 20. 24 x 2.5-inch SAS/SATA with fPERC (H965i)This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
SL4_CPU1_PB2 (signal connector on system board)
CTRL_DST_PB1 (fPERC input connector)
4
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SB1 (backplane expander signal connector)
5
CTRL_SRC_SA1 (fPERC controller connector)
BP_DST_SA1 (backplane expander signal connector)
6
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 21. 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch NVMe with fPERC (H965i)This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
SL4_CPU1_PB2 (signal connector on system board)
CTRL_DST_PB1 (fPERC input connector)
4
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SB1 (backplane expander signal connector)
5
CTRL_SRC_SA1 (fPERC controller connector)
BP_DST_SA1 (backplane expander signal connector)
6
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
7
SL11_CPU1_PB7 (signal connector on system board)
BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
8
SIG_PWR_0 (system board power connector)
BP_PWR_1 (rear backplane power connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 22. 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch SAS/SATA with fPERC (H965i)This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
SL4_CPU1_PB2 (signal connector on system board)
CTRL_DST_PB1 (fPERC input connector)
4
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SB1 (backplane expander signal connector)
5
CTRL_SRC_SA1 (fPERC controller connector)
BP_DST_SA1 (backplane expander signal connector)
6
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
7
BP_SRC_SA2 (backplane expander signal connector)
BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
8
SIG_PWR_0 (system board power connector)
BP_PWR_1 (rear backplane power connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 23. 24 x 2.5-inch SAS/SATA + 4 x 2.5-inch SAS/SATA with fPERC (H965i)This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
SL4_CPU1_PB2 (signal connector on system board)
CTRL_DST_PB1 (fPERC input connector)
4
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SB1 (backplane expander signal connector)
5
CTRL_SRC_SA1 (fPERC controller connector)
BP_DST_SA1 (backplane expander signal connector)
6
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
7
BP_SRC_SA2 (backplane expander signal connector)
BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
8
SIG_PWR_0 (system board power connector)
BP_PWR_1 (rear backplane power connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 24. 24 x 2.5-inch SAS/SATA + 4 x 2.5-inch NVMe with fPERC (H965i)This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
SL4_CPU1_PB2 (signal connector on system board)
CTRL_DST_PB1 (fPERC input connector)
4
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SB1 (backplane expander signal connector)
5
CTRL_SRC_SA1 (fPERC controller connector)
BP_DST_SA1 (backplane expander signal connector)
6
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
7
SL11_CPU1_PB7 (signal connector on system board)
BP_DST_PA2 (rear backplane signal connector) and BP_DST_PB2 (rear backplane signal connector)
8
SL8_CPU1_PA4 (signal connector on system board)
BP_DST_PA1 (rear backplane signal connector) and BP_DST_PB1 (rear backplane signal connector)
9
SIG_PWR_0 (system board power connector)
BP_PWR_1 (rear backplane power connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 25. 24 x 2.5-inch SAS/SATA dual controller with fPERC (H965i) and APERC in Riser 2This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
SL4_CPU1_PB2 (signal connector on system board)
CTRL_DST_PB1 (fPERC input connector)
4
CTRL_SRC_SA1 (fPERC controller connector)
BP_DST_SA1 (backplane expander signal connector)
5
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
6
CTRL_SRC_SA1_PA1 (adapter PERC controller connector)
BP_DST_SB1 (backplane expander signal connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 26. 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch SAS/SATA dual controller with fPERC (H965i) and APERC in Riser 2This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
SL4_CPU1_PB2 (signal connector on system board)
CTRL_DST_PB1 (fPERC input connector)
4
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SB1 (backplane expander signal connector)
5
CTRL_SRC_SA1 (fPERC controller connector)
BP_DST_SA1 (backplane expander signal connector)
6
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
7
SIG_PWR_0 (system board power connector)
BP_PWR_1 (rear backplane power connector)
8
CTRL_SRC_SA1_PA1 (adapter PERC controller connector)
BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 27. 24 x 2.5-inch SAS/SATA with 8 universal (SAS/SATA/NVMe) slot and fPERC (H965i)This table shows connector information.
Order
From
To
1
SL1_CPU2_PA1 (signal connector on system board) and SL2_CPU2_PB1 (signal connector on system board)
BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
2
SL5_CPU2_PB3 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
SL6_CPU2_PA3 (signal connector on system board)
CTRL_DST_PB1 (fPERC input connector)
4
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
5
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SB1 (backplane expander signal connector)
6
CTRL_SRC_SA1 (fPERC controller connector)
BP_DST_SA1 (backplane expander signal connector)
7
SL3_CPU1_PA2 (signal connector on system board)
BP_DST_PA2 (backplane signal connector)
8
SL4_CPU1_PB2 (signal connector on system board)
BP_DST_PB2 (backplane signal connector)
9
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 28. 24 x 2.5-inch SAS/SATA with eight universal slots (SAS/SATA/NVMe) and fPERC (HBA355i, H355, H755)This table shows connector information.
Order
From
To
1
SL1_CPU2_PA1 (signal connector on system board) and SL2_CPU2_PB1 (signal connector on system board)
BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
2
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
3
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
4
SL4_CPU1_PB2 (signal connector on system board)
BP_DST_PA2 (backplane signal connector)
5
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SB1 (backplane expander signal connector)
6
CTRL_SRC_SA1 (fPERC controller connector)
NOTE:Tightening the connector screws secures the connector end.
BP_DST_SA1 (backplane expander signal connector)
7
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
8
SL7_CPU1_PB4 (signal connector on system board)
BP_DST_PB2 (backplane signal connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 29. 24 x 2.5-inch SAS/SATA with fPERC (HBA355i, H355, H755)This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SB1 (backplane expander signal connector)
4
CTRL_SRC_SA1 (fPERC controller connector)
NOTE:Tightening the connector screws secures the connector end.
BP_DST_SA1 (backplane expander signal connector)
5
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 30. 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch NVMe with fPERC (HBA355i, H355, H755)This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SB1 (backplane expander signal connector)
4
CTRL_SRC_SA1 (fPERC controller connector)
NOTE:Tightening the connector screws secures the connector end.
BP_DST_SA1 (backplane expander signal connector)
5
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
6
SIG_PWR_0 (system board power connector)
BP_PWR_1 (rear backplane power connector)
7
SL11_CPU1_PB7 (signal connector on system board)
BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 31. 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch SAS/SATA with fPERC (HBA355i, H355, H755)This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SB1 (backplane expander signal connector)
4
CTRL_SRC_SA1 (fPERC controller connector)
NOTE:Tightening the connector screws secures the connector end.
BP_DST_SA1 (backplane expander signal connector)
5
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
6
SIG_PWR_0 (system board power connector)
BP_PWR_1 (rear backplane power connector)
7
BP_SRC_SA2 (backplane expander signal connector)
BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 32. 24 x 2.5-inch SAS/SATA + 4 x 2.5-inch SAS/SATA with fPERC (HBA355i, H355, H755)This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SB1 (backplane expander signal connector)
4
CTRL_SRC_SA1 (fPERC controller connector)
NOTE:Tightening the connector screws secures the connector end.
BP_DST_SA1 (backplane expander signal connector)
5
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
6
SIG_PWR_0 (system board power connector)
BP_PWR_1 (rear backplane power connector)
7
BP_SRC_SA2 (backplane expander signal connector)
BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 33. 24 x 2.5-inch SAS/SATA + 4 x 2.5-inch NVMe with fPERC (HBA355i, H355, H755)This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SB1 (backplane expander signal connector)
4
CTRL_SRC_SA1 (fPERC controller connector)
NOTE:Tightening the connector screws secures the connector end.
BP_DST_SA1 (backplane expander signal connector)
5
SL4_CPU1_PB2 (signal connector on system board)
BP_DST_PA1 (rear backplane signal connector) and BP_DST_PB1 (rear backplane signal connector)
6
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
7
SIG_PWR_0 (system board power connector)
BP_PWR_1 (rear backplane power connector)
8
SL11_CPU1_PB7 (signal connector on system board)
BP_DST_PA2 (rear backplane signal connector) and BP_DST_PB2 (rear backplane signal connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 34. 24 x 2.5-inch SAS/SATA dual controller with fPERC (HBA355i, H355, H755) and APERC in Riser 2This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
CTRL_SRC_SA1 (fPERC controller connector)
NOTE:Tightening the connector screws secures the connector end.
BP_DST_SA1 (backplane expander signal connector)
4
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
5
CTRL_SRC_SA1_PA1 (adapter PERC controller connector)
BP_DST_SB1 (backplane expander signal connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 35. 24 x 2.5-inch SAS/SATA + 2 x 2.5-inch SAS/SATA dual controller with fPERC (HBA355i, H355, H755) and APERC in Riser 2This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SB1 (backplane expander signal connector)
4
CTRL_SRC_SA1 (fPERC controller connector)
BP_DST_SA1 (backplane expander signal connector)
5
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
6
SIG_PWR_0 (system board power connector)
BP_PWR_1 (rear backplane power connector)
7
CTRL_SRC_SA1_PA1 (adapter PERC controller connector)
BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 36. 24 x 2.5-inch SAS/SATA with 8 universal (SAS/SATA/NVMe) slots and fPERC (HBA355i, H355, H755)This table shows connector information.
Order
From
To
1
SL1_CPU2_PA1 (signal connector on system board) and SL2_CPU2_PB1 (signal connector on system board)
BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
2
SL5_CPU2_PB3 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
4
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SB1 (backplane expander signal connector)
5
CTRL_SRC_SA1 (fPERC controller connector)
NOTE:Tightening the connector screws secures the connector end.
BP_DST_SA1 (backplane expander signal connector)
6
SL3_CPU1_PA2 (signal connector on system board)
BP_DST_PA2 (backplane signal connector)
7
SL4_CPU1_PB2 (signal connector on system board)
BP_DST_PB2 (backplane signal connector)
8
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 37. 24 x 2.5-inch SAS/SATA with 4 universal (SAS/SATA/NVMe) slots+ 4 x 2.5-inch SAS/SATA with fPERC (HBA355i)This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
CTRL_SRC_SB1 (fPERC controller connector)
BP_DST_SB1 (backplane expander signal connector)
4
CTRL_SRC_SA1 (fPERC controller connector)
NOTE:Tightening the connector screws secures the connector end.
BP_DST_SA1 (backplane expander signal connector)
5
SL4_CPU1_PB2 (signal connector on system board)
BP_DST_PA2 (backplane signal connector)
6
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
7
SL7_CPU1_PB4 (signal connector on system board)
BP_DST_PB2 (backplane signal connector)
8
SIG_PWR_0 (system board power connector)
BP_PWR_1 (rear backplane power connector)
9
BP_SRC_SA2 (backplane expander signal connector)
BP_DST_SA1 (rear backplane signal connector) and BP_DST_SB1 (rear backplane signal connector)
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 38. 16 x 2.5-inch (8 x SAS/SATA with fPERC (HBA355i, H355, H755) + 8 x NVMe RAID with fPERC (H755N))This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
4
CTRL_SRC_PB1 (fPERC controller connector)
BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
5
CTRL_SRC_PA1 (fPERC controller connector)
BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
6
SL7_CPU1_PB4 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
NOTE:An 8 x 2.5-inch NVMe backplane with fPERC H755N should be assembled outside and inserted into the system, along with all necessary cables.
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 39. 16 x 2.5-inch (8 x SAS/SATA with fPERC (HBA355i, H355, H755) + 8 x NVMe RAID with fPERC (H965i))This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
4
CTRL_SRC_PB1 (fPERC controller connector)
BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
5
CTRL_SRC_PA1 (fPERC controller connector)
BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
6
SL7_CPU1_PB4 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
7
SL8_CPU1_PA4 (signal connector on system board)
CTRL_DST_PB1 (fPERC input connector)
NOTE:An 8 x 2.5-inch NVMe backplane with fPERC H965i should be assembled outside and inserted into the system, along with all necessary cables.
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 40. 16 x 2.5-inch (8 x SAS/SATA with fPERC (H965i) + 8 x NVMe RAID with fPERC (H755N))This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
SL4_CPU1_PB2 (signal connector on system board)
CTRL_DST_PB1 (fPERC input connector)
4
CTRL_SRC_PA1 (fPERC controller connector)
BP_DST_SA1 (backplane signal connector)
5
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
6
CTRL_SRC_PB1 (fPERC controller connector)
BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
7
CTRL_SRC_PA1 (fPERC controller connector)
BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
8
SL7_CPU1_PB4 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
NOTE:An 8 x 2.5-inch NVMe backplane with fPERC H755N should be assembled outside and inserted into the system, along with all necessary cables.
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.
Table 41. 16 x 2.5-inch (8 x SAS/SATA with fPERC (H965i) + 8 x NVMe RAID with fPERC (H965i))This table shows connector information.
Order
From
To
1
SIG_PWR_1 (system board power connector)
BP_PWR_1 (backplane power connector)
2
SL3_CPU1_PA2 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
3
SL4_CPU1_PB2 (signal connector on system board)
CTRL_DST_PB1 (fPERC input connector)
4
CTRL_SRC_PA1 (fPERC controller connector)
BP_DST_SA1 (backplane signal connector)
5
SIG_PWR_2 (system board power connector)
BP_PWR_2 (backplane power connector)
6
CTRL_SRC_PB1 (fPERC controller connector)
BP_DST_PA2 (backplane signal connector) and BP_DST_PB2 (backplane signal connector)
7
CTRL_SRC_PA1 (fPERC controller connector)
BP_DST_PA1 (backplane signal connector) and BP_DST_PB1 (backplane signal connector)
8
SL7_CPU1_PB4 (signal connector on system board)
CTRL_DST_PA1 (fPERC input connector)
9
SL8_CPU1_PA4 (signal connector on system board)
CTRL_DST_PB1 (fPERC input connector)
NOTE:An 8 x 2.5-inch NVMe backplane with fPERC H965i should be assembled outside and inserted into the system, along with all necessary cables.
NOTE: Follow the sequential order as shown in the table to remove the cables, to install the cables follow the reverse sequential order.