- Notes, cautions, and warnings
- Revision history
- Overview
- Updating firmware for PowerEdge MX solution
- MX7000 Solution Baselines
- Upgrading Ethernet switch using DUP
- OME-Modular licenses
- Logging in to OME-Modular
- Logging in to OME–Modular as local, Active Directory, or LDAP user
- Logging in to OME-Modular using OpenID Connect
- OME-Modular home page
- Viewing device health
- Setting up chassis
- Initial configuration
- Configuring chassis settings
- Managing chassis
- Chassis groups
- Controlling chassis power
- Backing up chassis
- Restoring chassis
- Ethernet switch backup instructions
- Exporting chassis profiles
- Managing chassis failover
- Troubleshooting in chassis
- Extracting logs
- Blinking LEDs
- Interfaces to access OME-Modular
- Viewing chassis hardware
- Viewing chassis alerts
- Viewing chassis hardware logs
- Configuring OME–Modular
- Managing compute sleds
- Managing Profiles
- Managing storage
- Managing templates
- Managing identity pools
- Ethernet IO Modules
- MX Scalable Fabric architecture
- SmartFabric Services
- Managing networks
- Managing Fibre Channel IOMs
- Managing firmware
- Monitoring alerts and logs
- Monitoring audit logs
- Use case scenarios
- Troubleshooting
- Storage
- Firmware update is failing
- Storage assignment is failing
- SAS IOM status is downgraded
- SAS IOM health is downgraded
- Drives on compute sled are not visible
- Storage configuration cannot be applied to SAS IOMs
- Drives in OpenManage are not visible
- iDRAC and OpenManage drive information do not match
- The assignment mode of storage sled is unknown
- Unable to access OME-Modular using Chassis Direct
- Troubleshooting lead chassis failure
- Storage
- Recommended slot configurations for IOMs
- Updating components in phased update order through manual orchestration
- Creating validated firmware solution baseline using Dell Repository Manager
- Upgrading networking switch using different OS10 DUP versions
- Upgrading networking switch using CLI
- CLI commands not part of chassis backup
- VMware ESXi/MX Baseline Validation Matrix
- MX7000 Solution Baselines for previous versions
- OME-Modular firmware update matrix for previous versions
Dell OpenManage Enterprise-Modular Edition Version 2.00.00 for PowerEdge MX7000 Chassis User's Guide
Configure Quick Deploy settings
The
Quick Deploy feature enables you to configure the password to access the iDRAC user interface, IOMs, and IPv4 and IPv6 settings. These settings can be applied to existing compute sleds or IOM devices immediately. You can apply the
Quick Deploy settings to compute sleds when they are inserted into the chassis, later. However, you cannot apply the
Quick Deploy settings to IOMs that are inserted later.
When you insert a new sled into an empty slot with only quick deploy settings that are configured, it only creates an audit log instead of deployment and configuration job.
Quick deploy settings are validated when the job is run. If an invalid parameter is used, the quick deploy job fails. The Quick Deploy job parameters are not evaluated, as they can contain any value, which is delegated while running the job.
Enabling and disabling quick deploy is a web interface feature to determine if the controls are enabled to configure Quick Deploy settings. The back-end only processes requests from the web interface.
NOTE: After the quick deploy settings are applied to the compute sled, the IP configuration is displayed in the
OME–Modular web interface, when the inventory is refreshed.
NOTE: When IPv4 for IPv6 is disabled for MXG610s IOMs, the Device IPv4 address or Device IPv6 address is blank on the
Quick Deploy page for IOMs. However, for network IOMs, the IPv4 and IPv6 device addresses are
:: and
0.0.0.0.
To configure the Quick Deploy settings:
-
Click
.
The Quick Deploy configuration section is expanded.
-
Enter and confirm the password to access the iDRAC user interface.
The password can be up to 20 characters in length.NOTE: If any iDRAC IP configuration is modified, the SSO for the SLEDs is functional from the OME-Modular console only after the default inventory task or manual inventory refresh is complete.
-
In the
Management IP section, select
IPv4 Enabled to enable the IPv4 network settings and select the
IPv4 Network Type.
The available options are:
- Static
- DHCP
-
Enter the
IPv4 Subnet Mask and
IPv4 Gateway.
NOTE: The IPv4 Subnet Mask and IPv4 Gateway options are displayed only if the IPv4 Network Type is "Static" .
-
Select
IPv6 Enabled to enable the IPv6 network settings and select the
IPv6 Network Type.
The available options are:
- Static
- DHCP
- If the IPv6 Network Type is Static, select the IPv6 Prefix Length and enter the IPv6 Gateway.
- From the list of slots that is displayed, select the check box next to the slot number to which you want to apply the Quick Deploy settings.
- In the Network IOM Settings section, enter and confirm the password to log in to the IOM interface.
-
Select
IPv4 Enabled to enable the IPv4 network settings and select the
IPv4 Network Type.
The available options are:
- Static
- DHCP
-
Enter the
IPv4 Subnet Mask and
IPv4 Gateway.
NOTE: The IPv4 Subnet Mask and IPv4 Gateway options are displayed only if the IPv4 Network Type is "Static".
-
Select
IPv6 Enabled to enable the IPv6 network settings and select the
IPv6 Network Type.
The available options are:
- Static
- DHCP
- If the IPv6 Network Type is Static, select the IPv6 Prefix Length and enter the IPv6 Gateway.
- Click Apply to save the Quick Deploy settings.
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\