WARNING There is an automatic initialization in the background which starts and if there are some user data it will be erased.
The
Create Virtual Disk Advanced Wizard allows you to specify the read, write, and cache policy, and parameters such as RAID level, bus protocol, media type, and encrypted disk for the virtual disk. You can also select the physical disks and the controller connector. You must have a good knowledge of RAID levels and hardware, to use the Advanced Wizard. If you want the wizard to choose a recommended virtual disk configuration for you, select the
Express Wizard option.
NOTE This task is not supported on PERC hardware controllers running in
HBA mode.
To create a virtual disk using the
Create Virtual Disk Advanced Wizard:
On the left-hand side of the Server Administrator page, expand
Storage.
Click on the
<PERC Controller>.
Click on
Virtual Disks.
The
Virtual Disk(s) on Controller <Controller Name> page is displayed.
Click
Go to the Create Virtual Disk Wizard.
The
Create Virtual Disk Wizard (Step 1) <Controller Name> page is displayed.
Select the
Advanced Wizard option.
To make sure that only encrypted physical disks are used to create the virtual disk, select
Yes from the
Create Encrypted Virtual Disk drop-down list.
The RAID levels are available for selection based on the number of encrypted physical disks.
If you select
No, the RAID levels are available based on the total number of physical disks present on the system.
Select the required RAID level from the drop-down list.
Depending on the controller,
Concatenated enables you to combine the storage capacity of several disks or to create a virtual disk using a single physical disk. For more information on the number of supported physical disks supported by
Concatenated, see
Number Of Physical Disks Per Virtual Disk. Using
Concatenated does not provide data redundancy or affect the read/write performance.
Select
RAID 0 for striping. This selection groups
n disks together as a large virtual disk with a total capacity of n disks. Data is alternately stored in the disks so that they are evenly distributed. Data redundancy is not available in this mode. Read/write performance is enhanced.
Select
RAID 1 for mirroring disks. This selection groups two disks as one virtual disk with the capacity of a single disk. The data is replicated on both disks. When a disk fails, the virtual disk continues to function. This feature provides data redundancy and good read performance, but slightly slower write performance. The system must have at least two physical disks to use RAID 1.
Select
RAID 5 for striping with distributed parity. This selection groups n disks together as one large virtual disk with a capacity of (n-1) disks. When a disk fails, the virtual disk continues to function. This feature provides better data redundancy and read performance, but slower write performance. The system must have at least three physical disks to use RAID 5.
Select
RAID 6 for striping with additional distributed parity. This selection groups
n disks as one large virtual disk with a capacity of (n- 2) disks. The virtual disk remains functional with up to two disk failures. RAID 6 provides better read performance, but slower write performance. The system must have at least four physical disks to use RAID 6.
Select
RAID 10 for striping over mirror sets. This selection groups n disks together as one large virtual disk with a capacity of (n/2) disks. Data is striped across the replicated mirrored pair disks. When a disk fails, the virtual disk continues to function. The data is read from the surviving mirrored pair disk. This feature provides the best failure protection and read/write performance. The system must have at least four physical disks to use RAID 10. For PERC controllers with firmware version 6 and later, RAID 10 also allows you to create a single span virtual disk with 22 or 26 physical drives.
Intelligent Mirroring — Automatically calculates the span composition based on the physical disks you select.
Spans are not displayed on this page. Select
Continue to view the span grouping on the Summary page. Click
Exit Wizard to cancel the virtual disk creation.
Storage Management calculates the optimum span composition as follows:
Determining span calculation:
Calculating the number of disks that can be utilized from the selected disks.
Maximizing the number of spans to increase the I/O performance
Determining the mirror for the physical disks: The mirror is determined in a way that ensures maximum redundancy. The algorithm also tries to match a physical disk for its mirror, to a disk that is almost the same size. However,
Intelligent Mirroring gives priority to size over redundancy.
The algorithm determines the candidate mirror in the following order:
Across connectors at the same level of enclosure and same size.
Across connectors in the enclosure that are not at the same level but of same size.
Across enclosures connected to the same connector and to a disk of the same size.
Within the enclosure with a physical disk of acceptable size difference.
Across connectors at the same level of enclosure and of acceptable size difference.
Across connectors in the enclosure that are not at the same level of the enclosure but with a physical disk of acceptable size difference.
If the size difference is not acceptable, the disk is not mirrored and hence dropped from the span. The number of spans and disks in the span is recalculated.
NOTE It is recommended that you use
Intelligent Mirroring to create RAID 10 across enclosures for simple and optimum configuration.
NOTE After a hard disk being used to create RAID 10 VD with
Intelligent Mirroring enabled, the same disk cannot be used to create another RAID 10 VD with
Intelligent Mirroring enabled.
NOTE To view the redundancy across enclosures achieved through
Intelligent Mirroring, click the virtual disk and view the physical disk IDs in each span, which are from alternate enclosures.
Select
RAID 50 to implement striping across more than one span of physical disks. RAID 50 groups
n*s disks as one large virtual disk with a capacity of s*(n-1) disks, where s is the number of spans and n is the number of disks within each span.
Select
RAID 60 to implement striping across more than one RAID 6 span. RAID 60 groups
n*s disks as one large virtual disk with a capacity of
s*(n-2) disks, where
s is the number of spans and n is the number of disks within each span. RAID 60 provides increased data protection and better read performance, but slower write performance.'