PowerScale OneFS 9.3.0.0 CLI Command Reference

Syntax

isi network subnets modify <id>
  [--description <string>|--clear-description]
  [--dsr-addrs <ip_address>|--clear-dsr-addrs
  | --add-dsr-addrs <ip_address>|--remove-dsr-addrs
  <ip_address>]
  [--revert-dsr-address]
  [--gateway <ip-address>]
  [--gateway-priority <integer>]
  [--mtu <integer>]
  [--revert-mtu]
  [--prefixlen <prefixlen>]
  [--name <string>]
  [--sc-service-addr <ip_address_range>
  | --clear-sc-service-addrs|--add-sc-service-addrs
  <ip_address_range> | --remove-sc-service-addrs <ip_address_range>]
  [--sc-service-name <domain_name>]
  [--vlan-enabled <boolean>
  [--revert-vlan-enabled]
  [--vlan-id <integer>]
  [{--force | -f}]
  [{--verbose | -v}]
  [{--help| -h}]  
  

Options

<id>

Specifies the ID of the subnet that you want to modify. A subnet ID consists of a <groupnet_id>, followed by a ':', followed by a subnet name. A subnet name must be unique throughout the cluster, and can be up to 32 characters long. Supported characters are [a-zA-Z0-9-_]. The <groupnet_id> and ':' may be left off if the subnet is in the default groupnet.

A subnet in a groupnet: "example_groupnet:example_subnet"
        A subnet in the default groupnet: "example_subnet"

The groupnet name is optional if referring to the default groupnet0. Colons are also acceptable as delimiters between component names—for example, groupnet0:subnet1.

--description <string>

Specifies an optional description of the subnet. The description cannot exceed 128 bytes.

--clear-description

Clears the description of the subnet.

--dsr-addrs <ip_address>...

Specifies a list of IP addresses that use Direct Server Return (DSR). You need to specify --dsr-addrs for each additional IP address.

--clear-dsr-addrs

Clears list of IP addresses that use Direct Server Return.

--add-dsr-addrs <ip_address>...

Adds items to the list of IP addresses that use Direct Server Return. You need to specify--add-dsr-addrs for each additional IP address that you want to add.

--remove-dsr-addrs <ip_address>...

Removes items from the list of IP addresses that use Direct Server Return. You need to specify --remove-dsr-addrs for each additional IP address that you want to remove.

--revert-dsr-addrs

Sets the value of --dsr-addrs to the system default value.

--gateway <ip_address>

Specifies the gateway IP address used by the subnet.

--gateway-priority <integer>

Specifies priority of the subnet gateway, where the lowest number is of the highest priority.

--mtu <integer>

Sets the size of the maximum transmission unit (MTU) of the subnet that the cluster uses in network communication.

--revert-mtu

Sets the value of --mtu to the system default value.

--prefixlen <iprefixlen>

Sets the prefix size of the subnet.

--name <string>

Specifies the name for the subnet.

--sc-service-addrs <ip_address_range>...

Specifies a range of IP addresses in the subnet which will receive incoming DNS requests. You need to specify --sc-service-addrs for each additional IP address.

--clear-sc-service-addrs

Clears the list of SmartConnect Service IP addresses.

--add-sc-service-addrs <ip_address_range>...

Adds the items to the list of SmartConnect Service IP addresses. You need to specify --add-sc-service-addrs for each additional IP address you want to add.

--remove-sc-service-addrs <ip_address_range>...

Removes the items from the list of SmartConnect Service IP addresses. You need to specify --remove-sc-service-addrs for each additional IP address you want to remove.

--sc-service-name <domain_name>

Specifies the domain name corresponding to the SmartConnect Service IP address.

--vlan-enabled <boolean>

Enables VLAN tagging on the subnet.

--revert-vlan-enabled

Sets the value of --vlan-enabled to the system default value.

--vlan-id <integer>

Specifies the VLAN ID for all interfaces on this subnet.

{--force | -f }

Suppresses any prompts or warnings messages that would otherwise appear before or during the subnet modification operation.

{--verbose | -v}

Displays more detailed information.

{--help | -h}

Displays help for this command.