Event and Error Message Reference Guide for 13th Generation Dell PowerEdge ServersVersion 1.2

RAC001

Message: The command was successful.
Detailed Description: The command was successful.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC002

Message: General failure.
Detailed Description: An unknown error occurred.
Recommended Response Action: Do one of the following: 1) Rerun the command. 2) Reset iDRAC and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 1 (Critical)
: No alerts are applicable for this message

RAC003

Message: Missing required parameter arg1 .
Arguments: arg1 = parameter name
Detailed Description: One or more required parameters for the method are missing.
Recommended Response Action: Refer to the profile document and provide the required parameters.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC004

Message: Invalid parameter value for arg1 .
Arguments: arg1 = parameter
Detailed Description: The parameter value for the given parameter is invalid.
Recommended Response Action: Provide a valid parameter value for specified parameter.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC005

Message: Mismatch in AttributeName and AttributeValue count.
Detailed Description: The name value pairs do not match in the input specified in the method invocation parameters.
Recommended Response Action: Provide a valid (AttributeName, AttributeValue) pair.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC006

Message: The attribute value cannot be changed because it is of read-only type.
Detailed Description: The attribute value cannot be changed because it is of read-only type.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC007

Message: The attribute value is outside the acceptable range.
Detailed Description: The attribute value is outside the acceptable range.
Recommended Response Action: Enter a value within the range and retry the operation. For more information about the acceptable range, refer to the Dell Lifecycle Controller Remote Services Quick Start Guide and DCIM Profile Documents available at the support site.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC008

Message: Invalid boolean Value
Detailed Description: The attribute boolean value is not valid for the specified attribute.
Recommended Response Action: Provide valid boolean value for the specified attribute.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC009

Message: Input string length exceeds maximum length.
Detailed Description: The requested operation cannot be completed because the length of the input string exceeds maximum length allowed.
Recommended Response Action: Verify the string length and retry the operation. Refer to the Lifecycle Controller-Remote Services documentation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC010

Message: Input contains invalid character.
Detailed Description: The input value for the attribute being set contains characters that are not allowed.
Recommended Response Action: Retry the operation using valid input characters. Refer to the Lifecycle Controller-Remote Services documentation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0100

Message: The Smart Card is removed. Further communication is not possible.
Detailed Description: Communication with the Smart Card has been lost.
Recommended Response Action: Insert a valid Smart Card and try again.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0101

Message: The inserted Smart Card is not valid or the Smart Card reader is not supported.
Detailed Description: The data returned is not in a known format.
Recommended Response Action: This error may occur because: 1. Smart Card is invalid. Insert a valid Smart Card and try again. 2. Check connection between reader and system. 3. There may be an issue with the Smart Card reader. Try reinstalling the reader driver or use a different reader.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0102

Message: The Smart Card Logon plug-in is not installed. Install the plug-in from the iDRAC Web GUI to log in using Smart Card.
Detailed Description: The software to communicate with the Smart Card is not loaded in this browser. Smart Card can be used for log in only if the appropriate Smart Card software is installed in the browser.
Recommended Response Action: Install the plug-in prompted by the iDRAC Web GUI to log in using Smart Card.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0103

Message: This browser does not support Smart Card logon on iDRAC. Use Internet Explorer version 7.0 or later to use this feature.
Detailed Description: Smart Card login is only supported in newer versions of Internet Explorer.
Recommended Response Action: See the iDRAC help text or documentation for a list of supported browsers.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0104

Message: An incorrect PIN was entered.
Detailed Description: An invalid PIN was entered. Too many log in attempts with a Smart Card login can result in a user being locked out of the system.
Recommended Response Action: 1. Enter a valid Smart Card PIN and try again. 2. Use a different Smart Card.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0105

Message: The Smart Card reader cannot be detected. Check whether the reader is installed correctly.
Detailed Description: Communication with the Smart Card reader cannot be established, or is lost.
Recommended Response Action: This error may occur because: 1. Check connection between reader and system. 2. There may be an issue with the Smart Card reader. Try reinstalling the reader driver or use a different reader.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0106

Message: The Smart Card cannot be detected. Insert the Smart Card correctly.
Detailed Description: Communication with the Smart Card reader is established and a Smart Card is inserted, but there are problems reading the Smart Card.
Recommended Response Action: This error may occur because: 1. Make sure the Smart Card is seated correctly. 2. Smart Card is invalid. Insert a valid Smart Card and try again. 3. Check connection between reader and system. 4. There may be an issue with the Smart Card reader. Try reinstalling the reader driver or use a different reader.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0107

Message: The inserted Smart Card cannot be recognized. Ensure that the correct Smart Card CSP drivers are installed.
Detailed Description: Communication with the Smart Card reader is established and a Smart Card is inserted, but there are problems accessing the Smart Card. The appropriate Cryptographic Service Provider (CSP) drivers are not installed.
Recommended Response Action: There may be an issue with the Smart Card Cryptographic Service Provider (CSP) drivers. Use the client OS to install CSP driver. If the OS has problem with Smart Card, then there will have problem using the Smart Card. So make sure Smart Card can login with Windows OS.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0108

Message: An internal error is encountered. Insert a valid Smart Card and try again. (Does this and preceeding messages show up in the SEL?)
Detailed Description: A non-specific error is detected when accessing the Smart Card.
Recommended Response Action: Review the error message preceeding or following this message.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC011

Message: A configuration Job already exists, cannot process more set operations.
Detailed Description: A Job has already been scheduled to apply pending iDRAC attribute values. Additional configuration operations are not allowed while there is a configuration Job pending execution.
Recommended Response Action: Wait for the scheduled Job to complete before setting more attributes.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0113

Message: Remote Syslog Port value is invalid: Valid range is 1-65535 or 0x1-0xFFFF.
Detailed Description: Data entered is not an integer value in the valid range of numbers.
Recommended Response Action: Enter a Remote Syslog Port number. Expected range: [1-65535 or 0x1-0xFFFF]
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0115

Message: The Destination IP Address value is invalid.
Detailed Description: The IPv4 address does not conform to the addressing standard or the supported IPv4 address range.
Recommended Response Action: Enter the Destination IP Address value between [1.0.0.0 - 223.255.255.255 excluding: 127 (first octet), 0 or 255 (last octet)].
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0116

Message: Invalid Destination IPv6 Address.
Detailed Description: The entered IPv6 address does not conform to the addressing standard or the supported IPv6 address range.
Recommended Response Action: Enter a valid Destination IPv6 Address.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0117

Message: SD card is unavailable.
Detailed Description: The SD card is not present, or communication with the SD card is lost. This could result in reduced functionality and capabilities.
Recommended Response Action: This error may occur because: 1. Make sure the SD card is seated correctly. 2. The SD card is invalid. Insert a valid SD card of size greater than 256MB and try again.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0118

Message: Unsupported vFlash SD card detected.
Detailed Description: The SD card is not a valid vFlash SD card. The use of non-Dell media prevents the use of some extended capabilities and functions.
Recommended Response Action: Insert a supported vFlash SD card.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC012

Message: Unable to perform the operation because of insufficient user privileges.
Detailed Description: The user credentials supplied do not have sufficient privileges to perform the operation.
Recommended Response Action: Retry the operation with user credentials authorized for the requested operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0120

Message: The selected partition size exceeds the available space.
Detailed Description: Requested partition size exceeds the available space.
Recommended Response Action: Enter a partition size smaller than the unused space on the vFlash SD card.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0121

Message: SD card is not initialized.
Detailed Description: SD card not readable. The card must be initialized.
Recommended Response Action: Initialize the SD card before it can be used.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0124

Message: Invalid label: Label must be exclusively alphanumeric characters.
Detailed Description: All characters in the label must be alphanumeric.
Recommended Response Action: Enter all alphanumeric characters.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0126

Message: The label value is invalid. Expected range: 1-6 alphanumeric characters.
Detailed Description: The label field is empty. A label is required to create an empty partition.
Recommended Response Action: Enter a label that contains one to six alphanumeric characters.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0127

Message: The specified size must be a non-fractional numeric value.
Detailed Description: Size must be a whole number.
Recommended Response Action: Enter a whole number for the size field.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0128

Message: An error has occurred in vFlash.
Detailed Description: A non-specific error has been detected while accessing the vFlash.
Recommended Response Action: Try the operation again in a few minutes. If the problem persists, reset iDRAC before trying the operation again.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0129

Message: An error has occurred while initializing the SD card.
Detailed Description: No status response was returned after completing the initialization request.
Recommended Response Action: Try reinitalizing the card again in a few minutes.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC013

Message: Unable to run the method becuase an invalid FQDD is entered.
Detailed Description: The method cannot be run because an invalid FQDD is entered.
Recommended Response Action: Enter a valid FQDD and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0130

Message: An error has occurred while creating a partition.
Detailed Description: A seperate message will provide more detail about this error which was detected while creating the vFlash partition.
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0131

Message: An error has occurred while deleting a partition.
Detailed Description: A seperate message will provide more detail about this error which was detected while deleting the vFlash partition.
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0132

Message: An error has occurred while formatting a partition.
Detailed Description: A seperate message will provide more detail about this error which was detected while formatting the vFlash partition.
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0133

Message: An error has occurred while downloading a partition.
Detailed Description: A non-specific error has been detected when downloading the partition.
Recommended Response Action: Try downloading the partition again in a few minutes. If the problem persists, reset iDRAC before trying the operation again.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0134

Message: This operation is unavailable for non-vFlash SD cards.
Detailed Description: The SD card is not a valid vFlash SD card. The use of non-Dell media prevents the use of some extended capabilities and functions.
Recommended Response Action: Insert a valid vFlash SD card.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0135

Message: An error has occurred while detaching a partition.
Detailed Description: A seperate message will provide more detail about this error which was detected while detaching the vFlash partition.
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0136

Message: An error has occurred while attaching a partition.
Detailed Description: A seperate message will provide more detail about this error which was detected while attaching the vFlash partition.
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0137

Message: An error has occurred while changing the read-write state for the partition.
Detailed Description: A seperate message will provide more detail about this error which was detected while changing the read-write state of the vFlash partition.
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0138

Message: A valid certificate is not loaded.
Detailed Description: The retrieved certificate came back as a null or empty document.
Recommended Response Action: Upload a valid certificate.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC014

Message: Unable to run the method becuase an invalid attribute name is entered.
Detailed Description: The method cannot be run because an invalid attribute name is entered.
Recommended Response Action: Enter a valid attribute name and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0140

Message: Firmware update has failed.
Detailed Description: The firmware update process returned an Update Failed status.
Recommended Response Action: Try the firmware update again in a few minutes. If the problem persists, try uploading the firmware through another interface such as Web GUI, RACADM, or DUPs.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0141

Message: Firmware update verification failed: The update status is unknown.
Detailed Description: Firmware update verification process failed; the firmware update status is unknown.
Recommended Response Action: Verify if the firmware has been updated by checking the new firmware version number. If it has not been updated try the firmware update again in a few minutes. If the problem persists, try uploading the firmware through another interface such as Web GUI, RACADM, or DUPs.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0142

Message: File is not valid for iDRAC firmware update.
Detailed Description: The firmware update process identified an invalid firmware image.
Recommended Response Action: Upload a valid iDRAC firmware image.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0146

Message: Firmware rollback has failed.
Detailed Description: Firmware rollback operation failed.
Recommended Response Action: Try the operation after a few minutes. If the problem persists, reset iDRAC and repeat the operation.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0147

Message: Rollback firmware is not available.
Detailed Description: Firmware rollback image is missing or is corrupt.
Recommended Response Action: Upload a new firmware image.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0148

Message: Unable to retrieve the batteries information. The system is powered off.
Detailed Description: While the system is powered off it is unable to retrieve information about the batteries.
Recommended Response Action: Turn the system on to view this information.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0149

Message: Unable to retrieve the fan information. The system is powered off.
Detailed Description: While the system is powered off it is unable to retrieve information about the fans.
Recommended Response Action: Turn the system on to view this information.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC015

Message: Unable to run the method becuase the input value is not one of the possible values for AttributeName arg1 .
Arguments: arg1 = attribute name
Detailed Description: The input attribute value is not valid for the attribute identified in the message.
Recommended Response Action: Provide valid attribute value for the attribute identified in the message and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0150

Message: Unable to retrieve the intrusion sensor information. The system is powered off.
Detailed Description: While the system is powered off it is unable to retrieve information about system intrusion.
Recommended Response Action: Turn the system on to view this information.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0151

Message: Unable to retrieve the removable flash media information. The system is powered off.
Detailed Description: While the system is powered off it is unable to retrieve information about removable flash media.
Recommended Response Action: Turn the system on to view this information.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0152

Message: Unable to retrieve the power supply information. The system is powered off.
Detailed Description: While the system is powered off it is unable to retrieve information about power supplies.
Recommended Response Action: Turn the system on to view this information.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0153

Message: Non-redundant power mode: Check the system hardware manual for implications.
Detailed Description: Power redundancy is typically used to protect equipment from unexpected power disruption that could cause data loss or hardware damage.
Recommended Response Action: It is recommended to use power redundancy
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0154

Message: Non-redundant power mode: Secondary power supply has degraded.
Detailed Description: Displayed when a group of redundant power supplies has one or more individual power supplies with bad status.
Recommended Response Action: Replace the degraded power supply unit. Check the Power Supplies page for more information.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0155

Message: Unable to retrieve the temperature information. The system is powered off.
Detailed Description: While the system is powered off it is unable to retrieve information about system temperature.
Recommended Response Action: Turn the system on to view this information.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0156

Message: Unable to retrieve the voltage information. The system is powered off.
Detailed Description: While the system is powered off it is unable to retrieve information about system voltage.
Recommended Response Action: Turn the system on to view this information.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0158

Message: Uploading kerberos keytab has failed.
Detailed Description: The Kerberos keytab is needed by the iDRAC to authenticate itself to the Kerberos (Active Directory) server. It is created on the AD server, and issued for the iDRAC. Its like a password, and therefore should be kept secret.
Recommended Response Action: The Kerberos keytab file may be corrupt. Upload a valid Kerberos keytab file.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0159

Message: Certificate upload failed: No pending CSR or private key.
Detailed Description: Certificate upload failed because there is no pending Certificate Signing Request (CSR) or private key.
Recommended Response Action: Upload failed due to no pending Certificate Signing Request (CSR). Try creating a new CSR and then upload the certificate.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC016

Message: Unable to run the method becuase an invalid attribute name is entered.
Detailed Description: The method cannot be run because an invalid attribute name is entered.
Recommended Response Action: Enter a valid attribute name and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0160

Message: Certificate upload failed: Cannot validate the certificate.
Detailed Description: Certificate upload failed because the certificate could not be validated.
Recommended Response Action: Certificate may be corrupt. Try creating a new Certificate Signing Request (CSR) and then upload the certificate.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0169

Message: Certificate upload failed: Certificate is not valid.
Detailed Description: Certificate upload failed because the certificate is not valid.
Recommended Response Action: Certificate may be corrupt. Try creating a new Certificate Signing Request (CSR) and then upload the certificate.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC017

Message: Job created to apply the attribute value.
Detailed Description: The requested job has been created.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0171

Message: Certificate upload failed: Certificate has expired.
Detailed Description: Certificate upload failed because the certificate has expired.
Recommended Response Action: Certificate has expired. Try creating a new Certificate Signing Request (CSR) and then upload the certificate.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC018

Message: The Job is completed but with errors..
Detailed Description: All the tasks in the Job were attempted, but some did not complete successfully.
Recommended Response Action: Examine source of the errors by inspecting the results from the Job execution, and after resolving the issues, retry the operation. Job results can be retrieved from the Lifecycle Log or the WSMan API.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0180

Message: Certificate upload failed: Unable to get local issuer certificate from the Certification Authority (CA) for confirming the CA is legitimate.
Detailed Description: Certificate upload failed. Unable to get local issuer certificate. The local issuer certificate is the certificate for the Certificate Authority (CA) that has signed the certificate for the Active Directory (AD) server, unless it is self signed. The iDRAC needs to verify that the CA is legitimate.
Recommended Response Action: Certificate has expired. Try creating a new CSR and then upload the certificate.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC019

Message: Job did not complete successfully.
Detailed Description: The submitted job did not complete successfully.
Recommended Response Action: Examine source of the errors by inspecting the results from the job execution, and after resolving the issues, retry the operation. Job results can be retrieved from the Lifecycle Log or the WSMan API.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC020

Message: Completed
Detailed Description: The submitted job completed successfully.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0206

Message: Certificate upload failed: Not a certificate file.
Detailed Description: Certificate upload failed because this is not a certificate file.
Recommended Response Action: Upload a valid certificate.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0207

Message: Certificate upload failed.
Detailed Description: Certificate upload failed possibly due to poor network connection.
Recommended Response Action: Try the operation again in a few minutes. If the problem persists, issue a new Certificate Signing Request (CSR) and try again.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0208

Message: Upload failed: May be due to invalid key data.
Detailed Description: Upload failed possibly due to invalid key data.
Recommended Response Action: Upload a certificate with a valid key.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0209

Message: Certificate upload failed: iDRAC unable to upload at this time.
Detailed Description: Certificate upload failed because iDRAC unable to upload at this time.
Recommended Response Action: Try the operation again in a few minutes.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC021

Message: Unable to set static values for IPAddress Net mask or Gateway because DHCP is Enabled.
Detailed Description: The static values for IPAddress Net mask or Gateway cannot be set because DHCP is enabled.
Recommended Response Action: Disable DHCP to set static values for IPAddress Net mask or Gateway.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0211

Message: Firmware update has failed.
Detailed Description: Firmware update has failed. This may be due to a corrupt firmware image, poor network connection, or another issue.
Recommended Response Action: Download a new firmware image and try loading the firmware again.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0212

Message: Login failed. Verify that username and password is correct.
Detailed Description: This is a generic error message used on all the login pages.
Recommended Response Action: Enter valid credentials.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0213

Message: Missing Username.
Detailed Description: Login page is missing a username.
Recommended Response Action: Enter a valid username.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0214

Message: Missing Password.
Detailed Description: Login page is missing a password.
Recommended Response Action: Enter a valid password.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0215

Message: Login failed: User does not have Login to iDRAC privilege.
Detailed Description: Login failed because the user does not have Login to iDRAC privilege.
Recommended Response Action: Login to iDRAC privilege is needed.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0216

Message: Login failed.
Detailed Description: Login failed because of an unknown reason.
Recommended Response Action: Try the operation after a few minutes. If the problem persists, reset iDRAC and repeat the operation.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0217

Message: iDRAC is not responding.
Detailed Description: Client did not receive a response for the login request.
Recommended Response Action: Try pinging the iDRAC and then try again.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0218

Message: The maximum number of user sessions is reached.
Detailed Description: A maximum of 4 iDRAC Web GUI sessions can be open at any time.
Recommended Response Action: Close one or more sessions before opening another session.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0219

Message: Power command failed.
Detailed Description: Requested power state change has failed.
Recommended Response Action: Try the operation after a few minutes. If the problem persists, reset iDRAC and repeat the operation.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC022

Message: Unable to set values for User Password, IPMILan, IPMISerial or User Admin Privilege because the User Name is not configured.
Detailed Description: Unable to set values for User Password, IPMILan, IPMISerial or User Admin Privilege because the User Name is not configured.
Recommended Response Action: Set User Name before attempting to set values of other identified attributes.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0221

Message: The Destination E-mail Address is too long. The maximum length is 64 characters.
Detailed Description: The Destination E-mail Address can contain upto 64 characters.
Recommended Response Action: Enter an email address that contains upto 64 characters.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0222

Message: The Destination E-mail Address is invalid.
Detailed Description: The specified email address does not match an email address format. Ex: "janedoe@email.com."
Recommended Response Action: Enter a valid email address.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0223

Message: Enter an alphanumeric value or a valid symbol for the following (see the online help for more information):
Detailed Description: The Subject line in the email contains invalid characters.
Recommended Response Action: Invalid character. Enter a valid value as mentioned in the online help.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0224

Message: Invalid e-mail description.
Detailed Description: A partial string used to construct a complete error message.
Recommended Response Action: Enter a valid email description.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0225

Message: Sending the test mail failed.
Detailed Description: Sending the test mail failed. This will prevent alert messages from being sent to this email address.
Recommended Response Action: Confirm that: 1. A valid SMTP server address is configred in the iDRAC. 2. The remote email server is configured properly to send and receive emails.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0226

Message: Send Failed: Request processing failed.
Detailed Description: Sending the test mail failed. This will prevent alert messages from being sent to this email address.
Recommended Response Action: Confirm that: 1. A valid SMTP server address is configred in the iDRAC. 2. The remote email server is configured properly to send and receive emails.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0227

Message: SD card is not detected: Insert an SD Card of size greater than 256MB.
Detailed Description: The SD card is not present, or communication with the SD card is lost. This could result in reduced functionality and capabilities.
Recommended Response Action: This error may occur because: 1. Make sure the SD card is seated correctly. 2. The SD card is invalid. Insert a valid SD card of size greater than 256MB and try again.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0228

Message: SD Card is detected with an unrecognized format. Click Initialize to initialize the card.
Detailed Description: SD Card needs to be formatted to make it usable. The card must be initialized.
Recommended Response Action: Click Initialize to initialize the card and make it usable.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC023

Message: Unable to enable the User or set values for IPMILan, IPMISerial, or User Admin Privilege because the User Password is not configured.
Detailed Description: Unable to enable the User or set values for IPMILan, IPMISerial, or User Admin Privilege because the User Password is not configured.
Recommended Response Action: Set User Password before attempting to enable the other identified attributes.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0230

Message: This operation erases all data in the SD Card. Do you want to continue?
Detailed Description: This message is displayed when a confirmation is required to initialize the vFlash SD Card.
Recommended Response Action: Press OK to initialize the SD Card. This will erase all data. If undesired press Cancel.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0231

Message: This operation erases all data in the partition. Do you want to continue?
Detailed Description: This message is displayed when a confirmation is required to format the vFlash SD Card partition.
Recommended Response Action: Press OK to initialize this partition of the SD Card. This action will erase all the data in this partition. If undesired press Cancel.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0235

Message: vFlash image upload timed out.
Detailed Description: When uploading an image to the vFlash partition, the operation is unresponsive, and has timed out.
Recommended Response Action: Try uploading the vFlash image again.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0236

Message: Invalid image: Upload failed
Detailed Description: vFlash image upload failed because the image is not valid.
Recommended Response Action: Image may be corrupt. Try uploading a valid vFlash image.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0237

Message: An error occurred while uploading the vFlash image.
Detailed Description: A seperate message will provide more detail about this error which was detected while uploading the vFlash image.
Recommended Response Action: Try uploading the vFlash image again.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0238

Message: vFlash is currently in-use by another process. Try again later.
Detailed Description: vFlash is unable to service the request at this time. Try again later.
Recommended Response Action: Try the operation after a few minutes.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0239

Message: SD Card is write-protected.
Detailed Description: The contents of a write protected SD Card cannot be modified.
Recommended Response Action: Make sure the SD Card is not write-protected before attempting to change its contents.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC024

Message: Unable to VLAN is Disabled so cannot set VLAN Priority because VLAN is Disabled.
Detailed Description: Unable to VLAN is Disabled so cannot set VLAN Priority because VLAN is Disabled.
Recommended Response Action: Enable VLAN to set VLAN Priority.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0240

Message: vFlash is disabled.
Detailed Description: vFlash needs to be enabled before attempting this operation.
Recommended Response Action: Enable vFlash before trying the operation.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0241

Message: The specified size exceeds the maximum size of arg1 MB.
Arguments: arg1 = size
Detailed Description: SD Card does not have enough free space available.
Recommended Response Action: Delete existing data or insert a SD card of greater size and retry.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0242

Message: The selected partition does not exist.
Detailed Description: The vFlash partition does not exist. This may be due to another user deleting that partition.
Recommended Response Action: Refresh the Web GUI page to see the available partitions.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0243

Message: Partition failed: A partitioning conflict has occurred with another session.
Detailed Description: There was a conflict with a concurrent session. Another user may have logged inusing a separate browser or RACADM.
Recommended Response Action: There was a conflict with a concurrent session. Refresh the page to see the currently available options.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0244

Message: The partition label must be unique.
Detailed Description: This message is displayed when a duplicate vFlash partition name is entered.
Recommended Response Action: Enter a unique label name for the partition.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0245

Message: The partition is in-use by another process.
Detailed Description: The vFlash partition is in-use by another process. Therefore, the current operation cannot proceed.
Recommended Response Action: Try the operation after a few minutes or with another partition. If the problem persists, reset iDRAC and repeat the operation.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0246

Message: Partition is read-only.
Detailed Description: The contents of a read-only partition cannot be modified.
Recommended Response Action: Make sure the partition is writable before attempting to change its contents.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0247

Message: The partition is currently attached.
Detailed Description: This message is displayed when trying to format or download to an attached vFlash partition.
Recommended Response Action: Detach this partition and try again.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0248

Message: This operation deletes the partition permanently. Do you want to continue?
Detailed Description: This message is displayed when trying to delete a vFlash partition.
Recommended Response Action: Press OK to delete this partition of the SD Card. This action will erase all the data in this partition. If undesired press Cancel.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0249

Message: One or more partitions are in-use by another process.
Detailed Description: The vFlash partition is in-use by another process. Therefore, the current operation cannot proceed.
Recommended Response Action: Try the operation after a few minutes. If the problem persists, reset iDRAC and repeat the operation.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC025

Message: Unable to set values for DNS1 or DNS2 attributes because DNS from DHCP is Enabled.
Detailed Description: Unable to set static values for DNS1 or DNS2 when DNS from DHCP is Enabled.
Recommended Response Action: Disable DNS from DHCP to set values for DNS1 or DNS2.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0250

Message: One or more partitions are read-only.
Detailed Description: The vFlash partitions are read-only. Therefore, the current operation cannot proceed.
Recommended Response Action: Make sure the partitions are writable before attempting to change their contents.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0251

Message: One or more partitions are currently attached.
Detailed Description: The vFlash partitions are attached. Therefore, the current operation cannot proceed.
Recommended Response Action: Detach the partitions and try again.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0252

Message: One or more partitions are currently detached.
Detailed Description: The vFlash partitions are detached Therefore, the current operation cannot proceed.
Recommended Response Action: Attach the partitions and try again.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0253

Message: The IP Address is invalid. Expected range: [1.0.0.0 - 223.255.255.255 excluding: 127 (first octet), 0 or 255 (last octet)].
Detailed Description: This error message is displayed to indicate that the IPv4 address does not conform to the required format.
Recommended Response Action: Enter a valid IP Address. Expected range: [1.0.0.0 - 223.255.255.255 excluding: 127 (first octet), 0 or 255 (last octet)].
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0254

Message: The Gateway Address is invalid. Expected range: [0.0.0.0 or 1.0.0.0 - 223.255.255.255 excluding: 127 (first octet), 0 or 255 (last octet)].
Detailed Description: This error message is displayed to indicate that the IPv4 Gateway Address does not conform to the required format
Recommended Response Action: Enter a valid Gateway Address. Expected range: [0.0.0.0 or 1.0.0.0 - 223.255.255.255 excluding: 127 (first octet), 0 or 255 (last octet)].
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0255

Message: The Subnet Mask is invalid. Expected ranges are: 255.XXX.0.0 [Class A], 255.255.XXX.0 [Class B], 255.255.255.XXX [Class C], and XXX.0.0.0 [others], where XXX must be valid (0,128,192,224,240,248,252,254).
Detailed Description: This error message is displayed to indicate that the IPv4 Subnet Mask does not conform to the required format.
Recommended Response Action: Enter a valid Subnet Mask. Expected ranges are: 255.XXX.0.0 [Class A], 255.255.XXX.0 [Class B], 255.255.255.XXX [Class C], and XXX.0.0.0 [others], where XXX must be valid (0,128,192,224,240,248,252,254).
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0256

Message: The Preferred DNS Server Address is invalid. Expected range: [0.0.0.0 or 1.0.0.0 - 223.255.255.255 excluding: 127 (first octet), 0 or 255 (last octet)].
Detailed Description: This error message is displayed to indicate that the Preferred DNS IPv4 address does not conform to the required format.
Recommended Response Action: Enter a valid Preferred DNS Server Address. Expected range: [0.0.0.0 or 1.0.0.0 - 223.255.255.255 excluding: 127 (first octet), 0 or 255 (last octet)].
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0257

Message: The Alternate DNS Server Address is invalid. Expected range: [0.0.0.0 or 1.0.0.0 - 223.255.255.255 excluding: 127 (first octet), 0 or 255 (last octet)].
Detailed Description: This error message is displayed to indicate that the Alternate DNS IPv4 address does not conform to the required format.
Recommended Response Action: Enter a valid Alternate DNS Server Address. Expected range: [0.0.0.0 or 1.0.0.0 - 223.255.255.255 excluding: 127 (first octet), 0 or 255 (last octet)].
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0259

Message: Invalid IPv6 address.
Detailed Description: This error message is displayed to indicate that the IPv6 address does not conform to the required format.
Recommended Response Action: Enter a valid IPv6 address.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC026

Message: Unable to set DNS Domain Name because "Domain Name From DHCP" is Enabled.
Detailed Description: Unable to set DNS Domain Name because "Domain Name From DHCP" is Enabled.
Recommended Response Action: Disable "Domain Name From DHCP" to set values for DNS Domain Name.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0260

Message: Invalid IPv6 prefix length. Expected range: 0-128.
Detailed Description: The specified IPv6 address prefix length is invalid.
Recommended Response Action: Enter a valid IPv6 prefix length. Expected range: 0-128.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0261

Message: Invalid IPv6 gateway address.
Detailed Description: This error message is displayed to indicate that the IPv6 gateway address does not conform to the required format.
Recommended Response Action: Enter a valid IPv6 gateway address.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0262

Message: The Preferred IPv6 DNS Server Address is invalid.
Detailed Description: This error message is displayed to indicate that the Preferred IPv6 DNS Server address does not conform to the required format.
Recommended Response Action: Enter a valid Preferred IPv6 DNS server address.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0263

Message: The Alternate IPv6 DNS Server Address is invalid.
Detailed Description: This error message is displayed to indicate that the Alternate IPv6 DNS Server address does not conform to the required format.
Recommended Response Action: Enter a valid Alternate IPv6 DNS server address.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0265

Message: Specify the VLAN ID and VLAN Priority.
Detailed Description: If VLAN is enabled, specify the VLAN ID and VLAN Priority.
Recommended Response Action: Enter a VLAN ID and VLAN Priority.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0266

Message: Invalid VLAN ID. Expected range: 1-4094.
Detailed Description: Specify a valid VLAN ID.
Recommended Response Action: Enter a valid VLan ID. Expected range: 1-4094.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0267

Message: Invalid VLAN Priority. Expected range: 0-7.
Detailed Description: Specify a valid VLAN Priority.
Recommended Response Action: Enter a valid VLAN Priority. Expected range: 0-7.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0268

Message: NIC is disabled.
Detailed Description: The NIC is disabled. This may adversely affect the current operation, and might not allow subsequent GUI interactions to this NIC.
Recommended Response Action: Enable the NIC before performing the operation.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0269

Message: The NIC MTU is invalid. Expected range: 576-1500 or 0x240-0x5DC.
Detailed Description: Specify a valid NIC MTU.
Recommended Response Action: Enter a valid NIC MTU. Expected range: 576-1500 or 0x240-0x5DC.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC027

Message: Unable to set values for Speed or Duplex because Auto Negotiation is Enabled.
Detailed Description: Unable to set static values for Speed or Duplex when the Auto Negotiation attribute is enabled.
Recommended Response Action: Disable Auto Negotiation in order to set values for Speed or Duplex.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0270

Message: IPv4 and IPv6 are disabled.
Detailed Description: This is a warning message that continuing this operation does not allow subsequent GUI interactions to this NIC.
Recommended Response Action: Enable IPv4 or IPv6 before continuing the operation.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0271

Message: Continuing will lock user account.
Detailed Description: Locking the user account prevents them from gaining access to iDRAC.
Recommended Response Action: Press OK to lock this user account. This action will prevent future access for this user. If undesired press Cancel.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0272

Message: Disabling NIC will prevent the user from accessing the iDRAC remotely through Web GUI, Remote Racadm, Ssh, and Telnet. Local Racadm and serial interface will continue to work.
Detailed Description: If the the Enable NIC checkbox is cleared, remote access to iDRAC is disabled.
Recommended Response Action: Disable NIC only if remote access is undesired.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0273

Message: iDRAC access will be limited to running the Racadm utility on the local server or using the serial interface.
Detailed Description: If the the Enable NIC checkbox is cleared, remote access to iDRAC is disabled.
Recommended Response Action: Enable remote access to access iDRAC remotely.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0274

Message: See the iDRAC user documentation for more information on using the Racadm utility or the serial interface.
Detailed Description: If the the Enable NIC checkbox is cleared, remote access to iDRAC is disabled.
Recommended Response Action: See iDRAC user documentation for more information on using racadm.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0275

Message: Click OK to disable the NIC. Click Cancel to keep the setting unchanged.
Detailed Description: If the the Enable NIC checkbox is cleared, remote access to iDRAC is disabled.
Recommended Response Action: Disable NIC only if remote access is undesired.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0276

Message: To save the changes and update this page, click Apply.
Detailed Description: If the the Enable NIC checkbox is cleared, remote access to iDRAC is disabled.
Recommended Response Action: Click Apply to save changes.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0277

Message: Disabling IPv4 prevents access to iDRAC using an IPv4 address.
Detailed Description: This warning message appears when IPv4 is disabled.
Recommended Response Action: Use IPv6 network to access iDRAC remotely.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0278

Message: Disabling IPv6 prevents access to iDRAC using an IPv6 address.
Detailed Description: This warning message appears when IPv6 is disabled.
Recommended Response Action: Use IPv4 network to access iDRAC remotely.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0279

Message: Invalid Encryption Key. Expected format: 0 to 40 characters, even number of characters and no blank spaces are allowed.
Detailed Description: An invalid IPMI encryption key was entered.
Recommended Response Action: Enter a valid encryption key of up to 40 characters. Odd number of characters and blank spaces are not allowed.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC028

Message: Unable to Enable "DNS Domain Name From DHCP" or "DNS From DHCP" because DHCP is Disabled.
Detailed Description: The attributes "DNS Domain Name From DHCP" and "DNS From DHCP" are dependent on the attribute DHCP being Enabled. Currently DHCP is configured as Disabled.
Recommended Response Action: Set DHCP attribute to Enable to be able to Enable DNS Domain Name From DHCP or DNS From DHCP.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0280

Message: The IP Range Address is invalid. Expected range: 0.0.0.0 - 255.255.255.255.
Detailed Description: This error message is displayed to indicate that the IPv4 address does not conform to the required format.
Recommended Response Action: Enter a valid IP Range Address. Expected range: 0.0.0.0 - 255.255.255.255.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0281

Message: The IP Subnet Mask is invalid. Expected range: 0.0.0.0 - 255.255.255.255.
Detailed Description: This error message is displayed to indicate that the IP Subnet Mask does not conform to the required format.
Recommended Response Action: Enter a valid IP Subnet Mask. Expected range: 0.0.0.0 - 255.255.255.255.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0282

Message: IP Blocking Fail Count is invalid. Expected range: 2-16.
Detailed Description: This is the number of login failures attempted from an IP address before further login attempts are rejected from that address. The default value is 10.
Recommended Response Action: Enter a valid IP Blocking Fail Count. Expected range: 2-16.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0283

Message: IP Blocking Fail Window is invalid. Expected range: 10-65535.
Detailed Description: This is the time span (in seconds) within which IP Blocking Fail Count failures must occur to trigger the IP Blocking Penalty Time. The default value is 3600 seconds (1 hour).
Recommended Response Action: Enter a valid IP Blocking Fail Window. Expected range: 10-65535.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0284

Message: IP Blocking Fail Penalty Time is invalid. Expected range: 10-65535.
Detailed Description: This is the time span (in seconds) within which login attempts from an IP address with excessive failures are rejected. The default value is 3600 seconds (1 hour).
Recommended Response Action: Enter a valid IP Blocking Fail Penalty Time. Expected range: 10-65535.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0285

Message: User name cannot be empty.
Detailed Description: The user name cannot be empty when creating a user account.
Recommended Response Action: Enter a user name.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0286

Message: New Password and Confirm New Password fields cannot be empty.
Detailed Description: When creating a user account, the New Password and Confirm New Password fields cannot be empty.
Recommended Response Action: Enter valid passwords for New Password and Confirm New Password.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0288

Message: Invalid entry: Entry must be exclusively alphanumeric characters and valid symbols.
Detailed Description: All characters entered must be alphanumeric or valid symbols.
Recommended Response Action: Enter all alphanumeric characters and valid symbols.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0289

Message: Values in New Password and Confirm New Password fields do not match.
Detailed Description: When creating a user account, the same value must be entered for New Password and Confirm New Password.
Recommended Response Action: Enter the same values for both New Password and Confirm New Password.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC029

Message: Unable to complete the operation because necessary dependency values are not found in the input.
Detailed Description: The operation cannot be completed because necessary dependencay values are not found in the input.
Recommended Response Action: Refer to the Dell Lifecycle Controller Remote Services Quick Start Guide and Profile Documents available at the support site, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0290

Message: The user name cannot have spaces.
Detailed Description: The user name value does not accept spaces.
Recommended Response Action: Do not enter spaces in the user name. If desired, use underscores.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0291

Message: The user name cannot contain: /, \, @, ., or " (quotation mark).
Detailed Description: The user name value does not accept these characters.
Recommended Response Action: Do not enter /, \, @, ., or " (quotation mark) for user name.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0292

Message: A valid certificate is not loaded.
Detailed Description: This error is displayed when LDAP or Active Directory cannot find its certificate.
Recommended Response Action: Load a valid certificate.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0293

Message: When certificate validation is enabled, a valid root Certificate Authority (CA) certificate must be uploaded. The CA certificate is used to verify the directory server SSL certificate.
Detailed Description: This error is displayed when LDAP or Active Directory cannot find an associated Certificate Authority (CA) certificate.
Recommended Response Action: Upload a valid root Certificate Authority (CA) certificate.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0294

Message: The Character Accumulate Interval value is invalid. Expected range: 1-255.
Detailed Description: The amount of time iDRAC waits before sending a partial Serial Over LAN (SOL) data packet. This parameter is specified in milliseconds. It is recommended to use 10 milliseconds for optimal performance.
Recommended Response Action: Enter a valid Character Accumulate Interval value. Expected range: 1-255.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0295

Message: The Character Send Threshold value is invalid. Expected range: 1-255.
Detailed Description: This is the number of characters per Serial Over LAN (SOL) data packet. When the number of characters accepted by iDRAC is equal to or greater than the Character Send Threshold value, iDRAC starts transmitting SOL data packets that contain the numbers of characters equal to or less than the Character Send Threshold value. If a packet contains fewer characters than this value, it is defined to be a partial SOL data packet. It is recommended to use 255 characters for optimal performance.
Recommended Response Action: Enter a valid Character Send Threshold value. Expected range: 1-255.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0297

Message: Specify a Domain Controller Address must be configured.
Detailed Description: The Domain Controller Address be specified for Active Directory configuration.
Recommended Response Action: Enter a valid Domain Controller Address.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0298

Message: Root Domain Name must be configured.
Detailed Description: A Root Domain Name must be specified for Active Directory configuration.
Recommended Response Action: Root Domain Name must be configured.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC030

Message: This attribute is dependent on a related attribute that has an incorrect value.
Detailed Description: This attribute is dependent on a related attribute that has an incorrect value. The related attribute is the parent in a parent-child value dependency relationship and has an affect on what values the child attribute can have.
Recommended Response Action: Refer to the Lifecycle Controller - Remote Services User Guide or the DCIM iDRAC Card Profile to determine the required values for the related attribute and retry the operation with the appropriate value.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0301

Message: Remote File Share connection is unavailable. Check the settings and try again.
Detailed Description: User will be unable to connect to Remote File Share.
Recommended Response Action: Make sure proper connectivity exists between the client and the remote file share before using this feature.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0302

Message: iDRAC Express does not support this feature.
Detailed Description: This error message is displayed when iDRAC does not have a valid Enterprise license.
Recommended Response Action: Upgrade to iDRAC Enterprise for supporting this feature.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0303

Message: Virtual Console is disabled or you do not have the Access Virtual Console privilege.
Detailed Description: This error message is displayed when Virtual Console feature is unavailable.
Recommended Response Action: Enable Virtual Console and ask the administrator to grant Access Virtual Console privilege.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0304

Message: Firmware update is terminated.
Detailed Description: Firmware update is terminated.
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC031

Message: Unable to complete the operation because an incorrect username is entered.
Detailed Description: The operation cannot be completed because an incorrect username is entered.
Recommended Response Action: Enter a valid username and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC032

Message: Invalid value specified for DNS RAC name.
Detailed Description: The DNS RAC name specified is not valid.
Recommended Response Action: Retry operation with valid DNS RAC name.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC033

Message: Unable to enable attribute because IPv4 is Disabled.
Detailed Description: The specified attribute cannot be enabled since it depends on IPv4 to be enabled.
Recommended Response Action: Enable IPv4 and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC034

Message: Unable to create a job because the job queue is full.
Detailed Description: The job queue is full.
Recommended Response Action: Wait for existing jobs to run to completion or delete some jobs from the job queue.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC035

Message: No pending configurations.
Detailed Description: There are no pending values for the any of the iDRAC attributes.
Recommended Response Action: Make sure there are pending values for the attributes that are targeted for configuration.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC036

Message: Attribute dependency failed.
Detailed Description: The value of the specified attribute is dependent on the value of another attribute. The current value dependency is invalid. The other attribute value must be changed before the specified attribute value can be set.
Recommended Response Action: Refer to the Lifecycle Controller-Remote Services documentation for the specified attribute dependency on another attribute value and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC037

Message: No pending configurations to delete.
Detailed Description: There are no pending configurations to delete.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC038

Message: Unable to perform the operation due to an unknown error in iDRAC.
Detailed Description: The operation did not complete successfully because of an unknown error in the iDRAC.
Recommended Response Action: Retry the action. If the issue persists, reset the iDRAC.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC039

Message: Invalid parameter value for arg1 .
Arguments: arg1 = parameter
Detailed Description: The value provided for the specified parameter is invalid.
Recommended Response Action: Verify the value for the specified parameter. Refer to the Lifecycle Controller-Remote Services documentation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC040

Message: Missing parameters arg1 .
Arguments: arg1 = parameters
Detailed Description: One or more required parameters needed for the method invoked in the operation are missing.
Recommended Response Action: Verify that all required parameters are provided. Refer to the Lifecycle Controller-Remote Services documentation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0400

Message: iDRAC memory low.
Detailed Description: iDRAC is running low on memory.
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0401

Message: idracmonitor: arg1
Arguments: arg1 = error string
Detailed Description: Critical error from iDRAC service recovery program.
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 1 (Critical)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC						✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC041

Message: The set operation on the event filters failed.
Detailed Description: The event filters set operation did not complete successfully due to invalid input parameters.
Recommended Response Action: Verify the specified input parameters and retry the operation. Refer to the Lifecycle Controller-Remote Services documentation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC042

Message: Invalid number of input parameters.
Detailed Description: The number of input parameters provided is not valid to perform the operation.
Recommended Response Action: Verify that all required parameters are provided. Refer to the Lifecycle Controller-Remote Services documentation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC043

Message: Unable to update some event filter settings.
Detailed Description: Some event filter settings were not updated due to problems encountered processing the input parameters.
Recommended Response Action: Verify the input parameters provided and retry the operation. Refer to the Lifecycle Controller-Remote Services documentation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC044

Message: Unable to update some event filter settings.
Detailed Description: Some event filter settings were not updated due to problems encountered processing the input parameters.
Recommended Response Action: Verify the input parameters provided and retry the operation. Refer to the Lifecycle Controller-Remote Services documentation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC045

Message: Event filter does not exist for input parameter combination.
Detailed Description: The combination of input parameters provided did not match any event filters.
Recommended Response Action: Verify the combination of input parameters and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC046

Message: Unsupported event notification for the event filter specified.
Detailed Description: The event notfication selected is not supported for the event filter specified.
Recommended Response Action: Refer to the iDRAC User Guide and Lifecycle Controller documentation and retry the operation with a valid event notification selection on the specified filter.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC047

Message: Unsupported event action for the specified event filter.
Detailed Description: The event action selected is not supported for the event filter specified.
Recommended Response Action: Refer to the iDRAC User Guide and Lifecycle Controller documentation and retry the operation with a valid event action selection on the specified filter.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC048

Message: The operation was successful.
Detailed Description: The operation completed successfully.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC049

Message: Resource allocation failure.
Detailed Description: The operation did not complete successfully because of lack of memory or file space in the iDRAC.
Recommended Response Action: Reset the iDRAC and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 1 (Critical)
: No alerts are applicable for this message

RAC050

Message: Invalid country code.
Detailed Description: The country code is not entered in the correct format or does not exist. Refer to ISO 3166 for the correct country code format.
Recommended Response Action: Enter country code in the correct format as defined in ISO 3166. For example, United States = US.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0500

Message: There are no batteries to be displayed.
Detailed Description: Batteries cannot be displayed. This error may occur if the host system is powered off or there is a bad or disconnected cable for batteries connected to the controller.
Recommended Response Action: 1. Check if the host system is powered off or shutdown. 2. Verify that the batteries are connected properly.
Category: Storage (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0501

Message: There are no physical disks to be displayed.
Detailed Description: Physical disks cannot be displayed. This error may occur if the host system is powered off or the physical disks are removed. This may result in communication loss while retrieving controller data.
Recommended Response Action: 1. Check if the host system is powered off or shutdown. 2. Check if the physical disks are inserted into the enclosure or attached to the backplane. 3. There are no out-of-band capable controllers detected.
Category: Storage (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0502

Message: There are no virtual disks to be displayed.
Detailed Description: Virtual disks cannot be displayed. This error may occur if the host system is powered off or there are no virtual disks created.
Recommended Response Action: 1. Check if the host system is powered off or shutdown. 2. Check if virtual disks are created.
Category: Storage (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0503

Message: There are no out-of-band capable controllers to be displayed.
Detailed Description: Out-of-band controllers cannot be displayed. This error may occur if the host system is powered off, or controllers are removed or disconnected.
Recommended Response Action: Check if the host system is powered off or shutdown.
Category: Storage (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0504

Message: There are no enclosures to be displayed.
Detailed Description: Enclosures cannot be displayed. This error may occur if the host system is powered off, there is no enclosure connected to the controller, or there is a bad or disconnected adapter cable for the enclosure.
Recommended Response Action: 1. Check if the host system is ON. 2. Check if the Storage Enclosure is ON. 3. Verify that the adapter cables are properly connected and there are no bent pins.
Category: Storage (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0505

Message: There are no devices to be displayed.
Detailed Description: Devices are not displayed. This error may occur because these components are removed or disconnected.
Recommended Response Action: 1. Check if the host system is ON. 2. Check if the Storage Enclosure is ON. 3. Verify that the adapter cables are properly connected and there are no bent pins.
Category: Storage (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0506

Message: You do not have privileges to perform this operation.
Detailed Description: This error occurs when the user tries to access a program or function that is beyond user granted privileges.
Recommended Response Action: Contact the system administrator to perform the operation or grant the required privileges.
Category: Storage (RAC = RAC Event)
Severity: Severity 1 (Critical)
: No alerts are applicable for this message

RAC0507

Message: Unable to find the requested resource.
Detailed Description: The requested information cannot be displayed, because the system did not find any matching resource. This occurs because the system is turned off, resource is not present, or the resource is removed or deleted. For example, resources such as physicals disks, vFlash SD card, SSL certificate or custom signing certificate.
Recommended Response Action: Do one of the following and retry the operation: 1) Turn on the system. 2) Make the resource available.
Category: Storage (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0508

Message: An unexpected error occurred.
Detailed Description: The server encountered an unexpected condition. This may be due to invalid JavaScript Object Notation.
Recommended Response Action: Wait for few minutes and refresh the page. If the problem persists, contact service provider.
Category: Storage (RAC = RAC Event)
Severity: Severity 1 (Critical)
: No alerts are applicable for this message

RAC0509

Message: The server is temporarily unavailable. Try again after sometime
Detailed Description: The server is currently unable to handle the request due to temporary overloading or server maintenance.
Recommended Response Action: Wait for few minutes and refresh the page. If the issue persists, contact service provider.
Category: Storage (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC051

Message: Unsupported parameter name arg1 .
Arguments: arg1 = parameter name
Detailed Description: The parameter name is not supported.
Recommended Response Action: Remove the unsupported parameter and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0510

Message: There are no events to be displayed.
Detailed Description: This error occurs if Lifecycle log events have not occurred recently.
Recommended Response Action: No response action is required.
Category: Storage (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0511

Message: There are no physical disks to be displayed.
Detailed Description: Physical disks cannot be displayed. This error may occur if the host system is powered off, physical disks are removed, or incorrect filters are applied.
Recommended Response Action: 1. Check if the host system is powered off or shutdown. 2. Check if the physical disks are inserted into the enclosure or attached to the backplane. 3. Check if correct filters are applied. 4. Check that the Storage Enclosure is on. 5. verify that the adapter cables are properly connected and there are no bent pins.
Category: Storage (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0512

Message: There are no virtual disks to be displayed.
Detailed Description: Virtual disks cannot be displayed. This error may occur if the host system is powered off, no virtual disks were created, or incorrect filters are applied.
Recommended Response Action: 1. Check if the host system is ON. 2. Check if virtual disks are created. 3. Check if correct filters are applied. 4. Check if the Storage Enclosure is ON. 5. Verify that the adapter cables are properly connected and there are no bent pins.
Category: Storage (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0513

Message: There are no virtual disks to be displayed.
Detailed Description: There are no virtual disks to be displayed. There may be no virtual disks created, the controller(s) may not be in RAID mode, or there may be pending creation or deletion jobs that have not completed.
Recommended Response Action: Check the following: 1) Check if the server is turned off. If the server is turned off, turn it on and wait until POST completes. 2) If no virtual disks are created, to start the virtual disk creation process, click #{create_virtualdisk_link}. 3) If create virtual disk operation(s) are in a pending state, complete the creation process. To complete the virtual disk(s) creation, go to the Pendng Operations page and create a configuration job on the appropriate controller. 4) If delete virtual disk operation(s) are in pending state, then cancel the operation. To cancel delete virtual disk pending operation(s), go to the Pending Operations page and delete all pending operation(s) on the appropriate controller. 5) If the Controller(s) are in HBA mode, switch the controller(s) to RAID mode. To switch controller(s) to RAID mode using the F2 System Setup utility, go to Device Settings > RAID Controller > Controller Management > Advanced Controller Management > Switch to RAID mode.
Category: Storage (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0514

Message: Unable to create virtual disk(s) on the selected controller.
Detailed Description: Virtual disk(s) cannot be created because of one or more reasons identified in the Recommended Response Action.
Recommended Response Action: Check the following: 1) If no physical disk drives are available for virtual disk (VD) creation, install additional physical disk drives. 2) If the maximum number of VDs that can be created on the controller has been reached, a new VD cannot be created until an existing VD is deleted. 3) If the maximum number of VDs supported by drive group has been created, a new VD cannot be created until an existing VD is deleted from the selected drive group. 4) If the physical disk drive(s) are in non-RAID mode, convert them to RAID mode by pressing Ctrl+R while restarting the server, and then select the required controller. Press F2 and select the Convert to RAID capable option, and then complete the operation. 5) If a job is currently running or scheduled on the selected controller, the job must be completed or deleted before attempting a new operation. Status of the scheduled job can be viewed and managed on the Job Queue page on iDRAC. Click Job Queue link to view the status of the scheduled jobs.
Category: Storage (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0516

Message: Converting physical disk drives to RAID-compatible will overwrite any OS-created RAID arrays.
Detailed Description: Converting physical disk drives to RAID-compatible will overwrite any OS-created RAID arrays.
Recommended Response Action: Make sure that there are no OS-configured RAID arrays, and then click OK.
Category: Storage (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔	✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC052

Message: Unable to create a configuration job because an existing configuration job is already in progress.
Detailed Description: Unable to create a configuration job because an existing configuration job is already in progress. Only one configuration job for a component can run or can be processed at any time.
Recommended Response Action: Retry the operation after the existing configuration job is complete, or cancel the existing configuration job and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC053

Message: OS to iDRAC pass-through is disabled.
Detailed Description: One or more attributes being set are dependent on OS to iDRAC pass-through being enabled.
Recommended Response Action: Enable OS to iDRAC pass-through and retry the previous command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC054

Message: User account attributes cannot be reset to default values due to an internal error.
Detailed Description: The user account attributes cannot be reset to default values due to an internal error.
Recommended Response Action: Make sure the configuration XML file contains valid values for user account attributes and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC055

Message: User name cannot be cleared because the user account is enabled in the input configuration XML file.
Detailed Description: The user name for the user account cannot be cleared because the user account is enabled in the configuration XML file.
Recommended Response Action: Retry the operation after disabling the user account in the configuration XML file.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC056

Message: Unable to set the Authentication Protocol attribute to None because the Privacy Protocol attribute is enabled for user ID: arg1
Arguments: arg1 = user ID
Detailed Description: The Authentication Protocol attribute for the user account identified in the message cannot be disabled because the Privacy Protocol attribute is enabled. The Privacy Protocol for the user account is not set to None.
Recommended Response Action: Disable the Privacy Protocol attribute for the identified user ID account by setting the value to None, and retry the operation to set Authentication Protocol attribute to None.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0560

Message: RAC Software Initialization Error
Detailed Description: RAC Software Initialization error. Monitoring data will not be available for PERC and Network Cards
Recommended Response Action: Contact Dell Tech Support
Category: System Health (RAC = RAC Event)
Severity: Severity 3 (Informational)
Trap/EventID: 2531

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC	✔		✔	✔	✔	✔
CMC	✔		✔	✔	✔

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*		✔
CMC	✔	✔

RAC0561

Message: iDRAC to CMC communication link is not functioning for agent free monitoring of chassis PCIe slots.
Detailed Description: iDRAC lost connection with CMC proxy component that enables agent free monitoring of PCIe slots. Agent free monitoring will not be supported for Chassis PCIe slots while this connection is not functioning.
Recommended Response Action: Do the following: 1) Check the Lifecycle Log for the subsequent RAC0562 communications restored message that will indicate the link was re-established automatically. 2) If there is no subsequent RAC0562 message in the Lifecycle Log, restart the iDRAC. The iDRAC can be restarted by using the RACADM command line utility and entering "racadm racreset". 3) After the iDRAC has restarted, if the communications link is still not functioning, restart the CMC and check the Lifecycle Log for this link error after the CMC has restarted. 4) If the issue persists, contact your service provider.
Category: System Health (RAC = RAC Event)
Severity: Severity 3 (Informational)
Trap/EventID: 2531

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC	✔		✔	✔	✔	✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*		✔
CMC

RAC0562

Message: iDRAC-CMC communication restored for agent free monitoring of chassis PCIe slots.
Detailed Description: iDRAC automatically restored connection with CMC proxy component. Agent free Monitoring will now be supported for Chassis PCIe slots.
Recommended Response Action: No response action is required.
Category: System Health (RAC = RAC Event)
Severity: Severity 3 (Informational)
Trap/EventID: 2531

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC	✔		✔	✔	✔	✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*		✔
CMC

RAC057

Message: Unable to set Privacy Protocol to an enabled state because the Authentication Protocol attribute is set to None for the user ID: arg1
Arguments: arg1 = user ID
Detailed Description: The Privacy Protocol for the user cannot be enabled because the Authentication protocol is disabled.
Recommended Response Action: Enable the Authentication Protocol attribute for the identified user ID account, and retry the operation to set the Privacy Protocol to an enabled state.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC058

Message: AttributeValue is not unique for AttributeName arg1 .
Arguments: arg1 = attribute name
Detailed Description: The value provided for the specified attribute is not unique. For example, the user name for a user account must be unique.
Recommended Response Action: Provide a unique value for the specified attribute. For more information about the component being managed, see the DCIM Profile documentation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC059

Message: Unable to configure iDRAC time because Network Time Protocol (NTP) is enabled.
Detailed Description: When the Network Time Protocol (NTP) feature is enabled, the iDRAC will get time from the configured NTP server. Directly configuration of the iDRAC time is disabled when NTP is enabled.
Recommended Response Action: Disable Network Time Protocol (NTP) and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC060

Message: Unable to set the attribute because OpenManage Server Administrator (OMSA) is installed on the server arg1
Arguments: arg1 = attribute name
Detailed Description: The attribute identified in the message could not be set, because certain features cannot be enabled when OMSA is installed on the server.
Recommended Response Action: Uninstall OMSA, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0600

Message: Unable to retrieve the temperature information.
Detailed Description: Temperature information cannot be displayed. This error may occur if the server is powered off.
Recommended Response Action: Power on the server. If the server is already powered on, wait for a few minutes and refresh the page. If the problem persists, contact service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0601

Message: Unable to retrieve alert recurrence information.
Detailed Description: The server encountered an unexpected condition. This may be due to invalid JavaScript Object Notation.
Recommended Response Action: Wait for few minutes and refresh the page. If the problem persists, contact service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0602

Message: Invalid value for alert recurrence.
Detailed Description: The value for alert recurrence must be within the range 0-365.
Recommended Response Action: Enter a value between 0-365.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0603

Message: Updating Job Queue. Status of the update jobs can be viewed and managed within the Job Queue page.
Detailed Description: The Job Queue is updated with the selected update jobs. The status of the update jobs can be viewed and managed within the Job Queue page.
Recommended Response Action: Click Job Queue button to view the status of the update jobs.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0604

Message: System inventory may not be up-to-date because Collect System Inventory On Restart (CSIOR) is disabled.
Detailed Description: The system inventory may not be up-to-date because the Collect System Inventory On Restart (CSIOR) feature is disabled. The CSIOR feature retrieves detailed system inventory information during system startup and stores this information on iDRAC.
Recommended Response Action: Enable CSIOR, restart the system and retry the operation. To enable CSIOR, press F2 (System Setup) during system startup, navigate to iDRAC Settings >Lifecycle Controller, and select the Enabled option for Collect System Inventory on Restart.
Category: Configuration (RAC = RAC Event)
Severity: Severity 1 (Critical)
: No alerts are applicable for this message

RAC0605

Message: There are no jobs to be displayed.
Detailed Description: There are no jobs to be displayed.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0606

Message: The network connection test operation was successful.
Detailed Description: The selected network connection test operation was successsful.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0607

Message: Unable to perform OS to iDRAC Pass-Through with the current system configuration.
Detailed Description: The integrated NICs in the system do not support OS to iDRAC Pass-Through.
Recommended Response Action: Make sure the integrated NICs are enabled from BIOS setup and support OS to iDRAC Pass-Through, then retry the operation. To access BIOS setup, press F2 during system startup. For more information about OS to iDRAC Pass-Through, see iDRAC7 Users Guide.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0608

Message: The iDRAC will restart when the iDRAC firmware update is complete. All current user sessions will be closed.
Detailed Description: The message appears in Job Queue page when the iDRAC firmware update job status is downloading. Communication to the iDRAC will be lost when the iDRAC restarts to complete the firmware update.
Recommended Response Action: Reconnect iDRAC communications session after iDRAC is restarted. The iDRAC will be ready for login once the restart is complete.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0609

Message: The job arg1 has been successfully added to the job queue.
Arguments: arg1 = import or export job ID
Detailed Description: The import or export system configuration operation with the job ID indicated in the message was successfully added to the Job Queue.
Recommended Response Action: No response action is required. The status of jobs can be viewed on the Job Queue page.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC061

Message: Unable to set the IPMI Watchdog because the OS Watchdog is already enabled..
Detailed Description: The IPMI Watchdog can not be enabled at the same time as the OS Watchdog.
Recommended Response Action: Disable the OS Watchdog before enabling IPMI Watchdog.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0610

Message: The passphrase and confirm passphrase values entered do not match.
Detailed Description: Different values were entered for passpharse and confirm passpharse field.
Recommended Response Action: Values entered in passphrase and confirm passphrase fields must be the same.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0611

Message: IP Address cannot be blank.
Detailed Description: The IP address cannot be blank for import or export of system configuration profile operation.
Recommended Response Action: Enter a valid IP Address for network location.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0612

Message: Cancelling the firmware update operation will delete all the uploaded firmware files. Do you want to continue?
Detailed Description: Cancelling the firmware update operation will cancel all firmware updates selected and delete all uploaded firmware files.
Recommended Response Action: Select Yes to cancel the firmware update operation and delete all uploaded firmware files. Select No to dismiss the message and continue the firmware update operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0613

Message: The uploaded file is invalid.
Detailed Description: An internal error occurred because of an invalid file.
Recommended Response Action: Make sure to upload the required file in the correct format and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0614

Message: Incorrect password for PKCS#12 file.
Detailed Description: The specified password was incorrect for the PKCS#12 file.
Recommended Response Action: Make sure to use the correct password for the PKCS#12 file. If the PKCS#12 file is encrypted with a password, add it in required password box. Leave the password box empty if the file was not encrypted with a password.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0615

Message: Invalid PKCS#12 file.
Detailed Description: The contents of the PKCS12 file was not valid because one of the following: 1) Not a valid PKCS#12 file, 2) Not a valid pfx file or 3) Did not contain a valid key.
Recommended Response Action: Make sure to upload the file in PKCS#12 format. OpenSSL can be used to validate a PKCS#12 file.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0616

Message: Error while extracting custom signing certificate and private key from the PKCS#12 file.
Detailed Description: iDRAC was unable to continue with the operation after the PKCS#12 file was uploaded, because it is not able to extract the custom signing certificate and private key.
Recommended Response Action: Make sure to upload the PKCS#12 file that contains a valid custom signing certificate and private key.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0617

Message: An error was encountered while generating new SSL Certificate.
Detailed Description: An error occurred while generating new iDRAC SSL Certificate or signing it with new custom signing certificate.
Recommended Response Action: Make sure to upload an PKCS#12 file that contains a valid custom signing certificate and private key, then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0618

Message: Incorrect data entered.
Detailed Description: The data entered caused an error while processing the request.
Recommended Response Action: Make sure to enter the correct data and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0619

Message: The iDRAC firmware rollback will cause an iDRAC restart and all current user sessions will be closed.
Detailed Description: The message appears in Firmware Rollback page when the iDRAC firmware rollback action completed successfully.
Recommended Response Action: Reconnect iDRAC communications sessions after iDRAC is restarted. The iDRAC will be ready for login once the restart is complete.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC062

Message: Unable to set the WatchdogResetTime because the IPMI Watchdog state is disabled.
Detailed Description: The WatchdogResetTime can not be set if the IPMI Watchdog state is disabled.
Recommended Response Action: Enable the IPMI Watchdog state and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0620

Message: Lifecycle Controller is unable to delete the selected jobs.
Detailed Description: Lifecycle Controller is currently busy performing tasks. The selected jobs cannot be deleted until the following: 1) The Lifecycle Controller tasks are completed. 2) The system completes all the Power-on-Self-test (POST) operations.
Recommended Response Action: Wait until Lifecycle Controller completes the current tasks and the system completes Power-on Self-test (POST).
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0621

Message: Successfully completed the iDRAC firmware update. All current user sessions will be closed.
Detailed Description: The message appears in Job Queue page when the iDRAC firmware update job status is completed. Communication to the iDRAC will be lost .
Recommended Response Action: The iDRAC will be ready for login once the restart is complete.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0622

Message: An invalid certificate file is uploaded.
Detailed Description: The certificate file is invalid for one of the following reasons: 1) CA Certificate is corrupted, expired, or does not have signing privileges. 2) CA private key does not matchi with CA Certificate being uploaded.
Recommended Response Action: Make sure the CA certificate and private key are correct and retry the operation. The certificate can be validated using the OpenSSL tools.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0623

Message: The firmware versions on all the components of this server are up-to-date.
Detailed Description: A firmware update is not required for the components on the server, because current firmware versions are the latest available in the repository.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0624

Message: Unable to find the requested job type or ID.
Detailed Description: The requested operation could not be completed, because an incorrect job type or job ID is entered.
Recommended Response Action: Enter the correct job type or ID, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0625

Message: Unable to schedule, because the requested job schedule type is not enabled.
Detailed Description: The requested job cannot be scheduled, because job schedule types such as Automatic Backup or Automatic Update is not enabled.
Recommended Response Action: Enable the correct job schedule type, and then retry the operation. For example, to enable the Automatic Backup feature, select the Enable Automatic Backup option.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0626

Message: Unable to schedule, because an invalid schedule parameter is entered.
Detailed Description: The job cannot be scheduled, because all or some of the schedule parameters entered are incorrect.
Recommended Response Action: Enter correct input schedule parameters and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0627

Message: Unable to schedule, because the requested recurrent Automatic Backup job is already scheduled.
Detailed Description: The job cannot be scheduled, because the requested recurrent Automatic Backup job is already scheduled.
Recommended Response Action: Delete the current scheduled job, and then retry to create a new Automatic Backup job with a new schedule.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0628

Message: Unable to schedule, because the requested recurrent Automatic Update job is already scheduled.
Detailed Description: The job cannot be scheduled, because the requested recurrent Automatic Update job is already scheduled.
Recommended Response Action: Delete the current scheduled job, and then retry to create a new Automatic Update job with a new schedule.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0629

Message: Unable to schedule, because an invalid job type is entered.
Detailed Description: The job cannot be scheduled, because the requested job type is not supported.
Recommended Response Action: Enter a correct job type, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC063

Message: The string length of the provided value for arg1 is inappropriate.
Arguments: arg1 = attribute name
Detailed Description: The string length of the entered value for the attribute identified in the message may be less than the minimum length or greater than the maximum length allowed.
Recommended Response Action: Make sure that the string length is correct and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0630

Message: Unable to schedule, because an invalid network file share type is entered.
Detailed Description: The job cannot be scheduled, because the requested network file share type is not supported.
Recommended Response Action: Enter a correct network file share type, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0631

Message: Unable to access the network file share, because an invalid network file share name is entered.
Detailed Description: The requested network file share cannot be accessed, because an invalid network file share name is entered.
Recommended Response Action: Enter a valid network file share name, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0632

Message: Unable to access the network file share, because an invalid network file share hostname or IP address is entered.
Detailed Description: The requested network file share cannot be accessed, because an invalid hostname or IP address is entered.
Recommended Response Action: Enter a valid network file share hostname or IP address, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0633

Message: Unable to access the network file share, because an invalid network share password is entered.
Detailed Description: The requested network file share cannot be accessed, because an invalid password is entered.
Recommended Response Action: Enter a valid network file share password, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0634

Message: Unable to access the network file share, because an invalid network file share username is entered.
Detailed Description: The requested network file share cannot be accessed, because an invalid username is entered.
Recommended Response Action: Enter a valid network file share username, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0635

Message: Unable to access the network file share, because an invalid domain name is entered.
Detailed Description: The requested network file share cannot be accessed, because an invalid domain name is entered.
Recommended Response Action: Enter a valid domain name, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0636

Message: Unable to access the network file share, because an invalid proxy password is entered.
Detailed Description: The requested network file share cannot be accessed, because an invalid proxy password is entered.
Recommended Response Action: Enter a valid proxy password, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0637

Message: Unable to access the network file share, because an invalid proxy user name is entered.
Detailed Description: The requested network file share cannot be accessed, because an invalid proxy user name is entered.
Recommended Response Action: Enter a valid proxy user name, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0638

Message: Unable to access the network file share, because an invalid proxy host name or IP address is entered.
Detailed Description: The requested network file share cannot be accessed, because an invalid proxy host name or IP address is entered.
Recommended Response Action: Enter a valid proxy host name or IP address, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0639

Message: Unable to schedule, because an invalid minute value is entered.
Detailed Description: The job could not be successfully scheduled, because an invalid value is entered for minute while scheduling a job.
Recommended Response Action: Enter a correct value from 0 to 59, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC064

Message: iDRAC was successfully reset.
Detailed Description: iDRAC was successfully reset.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0640

Message: Unable to schedcule, because an invalid hour value is entered.
Detailed Description: The job could not be successfully scheduled, because an invalid value is entered for hour while scheduling a job.
Recommended Response Action: Enter a correct value from 0 to 23, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0641

Message: Unable to schedcule, because an invalid timevalue is entered.
Detailed Description: The job could not be successfully scheduled, because an invalid value is entered for time while scheduling a job.
Recommended Response Action: Enter a correct value in the HH:MM format, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0642

Message: Unable to schedule, because an invalid value is entered for the day of a month.
Detailed Description: The job could not be successfully scheduled, because an invalid value is entered for day of a month while scheduling a job.
Recommended Response Action: Enter a correct numerical value in the following format: Day [1 to 31] of every [1 to 12] month(s). For example, Day 4 of every 11 months. Retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0643

Message: Unable to schedule, because an invalid monthvalue is entered.
Detailed Description: The job could not be successfully scheduled, because an invalid value is entered for month while scheduling a job.
Recommended Response Action: Enter a correct numerical value in the following format: Day [1 to 31] of every [1 to 12] month(s). For example, Day 4 of every 11 months. Retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0644

Message: Unable to schedule, because an invalid ear value is entered.
Detailed Description: The job could not be successfully scheduled, because an invalid value is entered for year, while scheduling a job.
Recommended Response Action: Enter a correct value, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0645

Message: Unable to schedule, because an invalid value is entered for the recurrence frequency.
Detailed Description: The job could not be successfully scheduled, because an invalid value is entered for recurrence frequency while scheduling a job.
Recommended Response Action: Enter a correct value, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0646

Message: Unable to schedule, because an invalid value is entered for the day of the week.
Detailed Description: The job could not be successfully scheduled, because an invalid value is entered for day of the week while scheduling a job.
Recommended Response Action: Enter a correct value, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0647

Message: Unable to schedule, because an invalid value is entered for the week of the month.
Detailed Description: The job could not be successfully scheduled, because an invalid value is entered for week of the month while scheduling a job.
Recommended Response Action: Enter a correct value from 1 to 4, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0648

Message: Unable to process the request.
Detailed Description: The request cannot be processed, because the length of string entered for one of the input parameter is more than the specified length.
Recommended Response Action: Enter a string not more than 4095 characters in length, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0649

Message: Unable to process the request.
Detailed Description: Unable to process the request, because data is not entered or not selected in one or more mandatory fields.
Recommended Response Action: Make sure to enter or select data in all the mandatory fields, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC065

Message: iDRAC reset operation was not successful.
Detailed Description: The iDRAC reset operation was not successful. This may be due to IPMI communications issues.
Recommended Response Action: Do the following: 1) Retry the operation. 2) If the issue persists, remove AC input power from the server and re-apply AC power to the server and retry the operation. 3) If the issue constinues to persist, contact your service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0654

Message: No operations can be performed on the iDRAC Service Module.
Detailed Description: Unable to perform operations on the iDRAC Service Module (iSM) because the iSM is not installed on the server operating system. All fields in the iDRAC GUI iSM page are disabled.
Recommended Response Action: Make sure that the iDRAC Service Module is installed on the server operating system, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0655

Message: The Replicate Lifecycle Controller Log in OS Log and Auto System Recovery Action features are disabled in the iDRAC Service Module because the OpenManage Server Administrator is installed on the server operating system.
Detailed Description: The Replicate Lifecycle Controller Log in OS Log and Auto System Recovery Action features are disabled in the iDRAC Service Module because the OpenManage Server Administrator is installed on the server operating system.
Recommended Response Action: None
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0656

Message: Are you sure you want to disable the iDRAC Service Module on the server operating system?
Detailed Description: The iDRAC Service Module (iSM) service cannot be started by just enabling in iDRAC web interface because the service has to also be manually restarted on the server operating system.
Recommended Response Action: To re-enable the iDRAC Service Module (iSM), do the following: 1) Enable the iSM in the iDRAC web interface, 2) Start the iSM service on the server operating system.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0657

Message: The file name field must not be blank.
Detailed Description: The file name cannot be blank when performing the Backup Server Profile operation.
Recommended Response Action: Enter an appropriate file name, and then retry the operation.
Category: Audit (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0658

Message: The iDRAC Service Module service can now be manually started on the server operating system.
Detailed Description: The iDRAC Service Module service can now be started on the server operating system. This service needs to be started manually on the server operating system.
Recommended Response Action: None
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0659

Message: Unable to perform the storage configuration operation(s) on arg1 because a job is currently pending or is running on the adapter.
Arguments: arg1 = adapter name
Detailed Description: The storage configuration operation(s) cannot be performed on the adapter identified in the message because a job is currently pending or is running on the adapter.
Recommended Response Action: Wait for the job to completely run, or delete the job, and then retry the operation.To view the status of the scheduled jobs, go to the Job Queue page of iDRAC.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC066

Message: iDRAC is successfully reset to factory-default properties.
Detailed Description: iDRAC was successfully reset to factory-default properties.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0660

Message: Unable to access the specified file server location.
Detailed Description: The file server cannot be accessed because of incorrect credentials.
Recommended Response Action: Check the file server credentials and retry the operation.
Category: Audit (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0661

Message: Storage configuration operation - #(operation) is pending on the selected #{devicetype} : #{devicename}.
Detailed Description: Various storage configuration operations can be performed on different devices such as physical disks, virtual disks, controllers, or enclosures. The operations are applied to the device by creating a configuration job on the associated controller.
Recommended Response Action: To complete the storage configuration operation, create a storage configuration job with the necessary scheduling.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0662

Message: The Clear Foreign Configuration operation will delete the foreign virtual disk information from the controllers associated physical disk drives. Clearing will remove metadata associated with the virtual disks, making the physical disk drives available for creating new virtual disks. To remove foreign data, perform an initialization operation.
Detailed Description: Clear foreign configuration will delete the foreign virtual disk information from the controllers associated physical disk drives. Clearing will remove metadata associated with the virtual disks, making the physical disk drives available for creating new virtual disks. To remove foreign data, perform an initialization operation.
Recommended Response Action: Press OK to continue.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0663

Message: Resetting the selected PERC controllers configuration will delete all the virtual disks (VDs) and unassign hot-spares from the associated controller.
Detailed Description: Resetting the selected PERC controllers configuration will delete all the virtual disks (VDs) and unassign hot-spares from the associated controller.
Recommended Response Action: Press OK to continue.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0664

Message: Exporting the RAID Controller Log will take less than arg1 minutes. Job ID: #{jobID} is created for the RAID Controller Log Export operation.
Arguments: arg1 = number of minutes
Detailed Description: Exporting the RAID Controller Log will take less than the number of minutes identified in the message. The job identified in the message is created for the RAID Controller Log Export operation.
Recommended Response Action: To check the progress of the job click the Job Queue button.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0665

Message: RAID Controller Log data is being collected. This operation will take less than arg1 minutes.
Arguments: arg1 = number of minutes
Detailed Description: RAID Controller Log data is being collected. This operation will take less than the number of minutes identified in the message.
Recommended Response Action: Do not log off from the application until the log data collection process is completed.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0666

Message: A RAID Controller Log is created.
Detailed Description: A RAID Controller Log is created.
Recommended Response Action: To export the Log report, click OK. To delete the report, click Cancel.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0667

Message: This setting will be applied after the server has been turned off and turned on again. This may result in loss of configuration and/or access to physical disk drive(s).
Detailed Description: This setting will be applied after the server has been turned off and turned on again. This may result in loss of configuration and/or access physical disk drive(s) or virtual disk(s) being marked offline. This may also result in some disk(s) being identified as foreign disks. Foreign physical disk drive(s) or virtual disk(s) can be imported or cleared.
Recommended Response Action: Press OK to continue.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0668

Message: This setting will be applied during the next server restart. If the setting is not compatible with the RAID Controller, then LED status indicators on all the associated hard disk drives (HDDs) stop functioning.
Detailed Description: This setting will be applied during the next server restart. If the setting is not compatible with the RAID Controller, then LED status indicators on all the associated hard disk drives (HDDs) stop functioning.
Recommended Response Action: Press OK to continue.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0669

Message: Initializing the virtual disk will permanently delete data from the virtual disk.
Detailed Description: Initializing the virtual disk will permanently delete data from the virtual disk.
Recommended Response Action: Press OK to continue.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC067

Message: iDRAC reset to factory defaults operation was not successful.
Detailed Description: iDRAC reset to factory defaults operation was not successful. This may be due to IPMI communications issues.
Recommended Response Action: Do the following: 1) Retry the operation. 2) If the issue persists, remove AC input power from the server and re-apply AC power to the server and retry the operation. 3) If the issue constinues to persist, contact your service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0670

Message: Deleting the virtual disk will remove the virtual disk from the controllers configuration.
Detailed Description: Deleting the virtual disk will remove the virtual disk from the controllers configuration. If the specified virtual disk is a boot device, the server will not boot unless another boot device is selected in BIOS.
Recommended Response Action: If the specified virtual disk is a boot device, the server will not boot. Press OK to continue.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0671

Message: Going out of this page will not save the operations or configuration settings that were selected.
Detailed Description: Going out of this page will not save the operations or configuration settings that were selected.
Recommended Response Action: Press OK to continue. Press Cancel to continue working on the page.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0673

Message: OS Collector must be run on the server OS in order to export OS and Application Data. A virtual USB device labeled DRACRW has appeared in the server OS. This device contains the OS Collector utility, go to the Server OS and run the version of the utility appropriate to the OS type. After the OS Collector utility execution has completed, return to this page to finish exporting the Technical Support Report (TSR).
Detailed Description: To export operating system (OS) and application data, the OS Collector utility must be run on the server OS. A virtual USB device labeled DRACRW has appeared in the server OS. After the OS Collector utility execution has completed, return to this page to complete exporting the Tech Support Report (TSR).
Recommended Response Action: Invoke the OS Collector utility in the OS and wait for execution completion. Then return to this page to complete exporting the Technical Support Report (TSR).
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0674

Message: Export Report will create a zip file of XML and text-based logs intended for Dell Technical Support assistance with troubleshooting system issues. Choose Advanced Export Options to specify optional report settings and actions.
Detailed Description: Export Report will create a zip file of XML and text-based logs intended for Dell Technical Support assistance with troubleshooting system issues. Choose Advanced Export Options to specify optional report settings and actions.
Recommended Response Action: No response action is requried.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0675

Message: Results are not available for the search criterion entered.
Detailed Description: Results are not available for the search criterion entered.
Recommended Response Action: Enter another criterion and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔
CMC

RAC0676

Message: Unable to assign physical disk drives as global hotspare(s).
Detailed Description: Unable to assign physical disk drives as global hotspare(s). This may be because there are no disk drives available in a ready state or there are no virtual disks present.
Recommended Response Action: Do one of the following and retry the operation: 1) If there are no disk drives available in ready state, insert additional disk drives and make sure the drives are in ready state. 2) If no virtual disks are present, click <create virtualdisk link> and create at least one virtual disk. 3) If the physical disk drive(s) are in non-RAID mode, convert them to RAID mode by pressing Ctrl+R while restarting the server, and then select the required controller. Press F2 and select the Convert to RAID capable option, and then complete the operation.
Category: Storage (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0677

Message: No physical disk drives in ready state, no virtual disks are created, and no PCIe SSD drives are available to perform operations on.
Detailed Description: No physical disk drives in ready state, virtual disks, or PCIe SSD drives are available to perform operations on.
Recommended Response Action: Do one of the following: 1. If there are no disk drives available in ready state, insert additional disk drives and make sure the drives are in ready state. 2. If no virtual disks are present, click <create virtualdisk link> and create at least one virtual disk. 3. If PCIe SSD drives are inserted into the enclosure or attached to the backplane.
Category: Storage (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0678

Message: Unable to perform Prepare to Remove or Secure Erase operations on PCIe SSD disk drives.
Detailed Description: Unable to perform Prepare to Remove or Secure Erase operations on the PCIe SSD disk drives.
Recommended Response Action: Make sure PCIe SSD disk drives are inserted into the enclosure or attached to the backplane and retry the operation. If the issue persists, contact your service provider.
Category: Storage (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0679

Message: A job operation is already running. Retry the operation after the existing job is completed.
Detailed Description: Unable to process the request because a job operation is already running.
Recommended Response Action: Wait until the running job is completed or delete the scheduled job and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC068

Message: SHA256Password and Plain Password cannot be imported together.
Detailed Description: Both SHA256Password and Plain Password cannot be attempted to set together on Configuration import per user.
Recommended Response Action: One of either SHA256Password or Plain password can be attempted to be imported for an user.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0680

Message: Server iDRAC user credentials and/or BIOS passwords are not currently set to default credentials. The USB Configuration XML feature is not available unless default credentials are set.
Detailed Description: The USB Configuration XML feature is not available if the iDRAC user credentials and BIOS passwords are not set to default values.
Recommended Response Action: Reset the iDRAC user credentials and BIOS passwords to default and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0681

Message: Shared component updates through the Server OS or Lifecycle controller cannot be applied because the CMC setting for Chassis Management at Server Mode is not set to Manage and Monitor.
Detailed Description: Shared component updates through the Server OS or Lifecycle controller cannot be applied because the CMC setting for Chassis Management at Server Mode is not set to Manage and Monitor.
Recommended Response Action: To enable this feature do the following: 1) Launch CMC Web UI. 2) Navigate to Chassis Overview -> Setup -> General, and select Manage and Monitor option for the Chassis Management at Server Mode. 3) Click Apply to save changes in CMC. 4) Retry the operation in iDRAC. For more information, refer to the CMC User Guide.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0682

Message: Enabling iDRAC Direct USB Configuration XML allows any USB key containing a correctly formatted configuration XML file to reconfigure the server when plugged into the USB management port identified by the wrench icon. This may include operations on RAID configurations, user accounts, and alert settings.
Detailed Description: Enabling iDRAC Direct USB Configuration XML allows any USB key containing a correctly formatted configuration XML file to reconfigure the server when plugged into the USB management port identified by the wrench icon. This may include operations on RAID configurations, user accounts, and alert settings.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0683

Message: Unable to perform split mode configuration on enclosure(s).
Detailed Description: Unable to perform split mode configuration on enclosure(s).
Recommended Response Action: Check the following: 1) The controller must have Real Time Configuration Capability and the associated enclosure(s) must have Split Mode Capability in order to perform the operation. 2)The controller(s) associated with the enclosure(s) support real time configuration. To verify the controller real time configuration support, go to the Controller Properties page, select the required controller and verify the Real Time Configuration Capability value.3)The enclosure(s) supports split mode configuration. To verify the enclosure, go to the Enclosure Properties page, select the required enclosure, and verify the Enclosure Split Mode Capability property value.<br />"
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0684

Message: Unable to perform split mode configuration on the selected enclosures, because Lifecycle Controller is not enabled.
Detailed Description: Unable to perform split mode configuration on the selected enclosures, because Lifecycle Controller is not enabled.
Recommended Response Action: To enable Lifecycle Controller, reboot the server. During server startup, press F2 to enter System Setup. Go to iDRAC Settings -> Lifecycle Controller, select Enable, and save the changes. Retry the operation after the server has restarted.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0685

Message: A pending operation has been created for this arg1 operation.
Arguments: arg1 = task name
Detailed Description: A pending operation has been created for this operation identified in the message.
Recommended Response Action: To view the pending operations click the Pending Operations button.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0686

Message: Some of the applied pending operations were not created.
Detailed Description: Some of the applied pending operations were not created.
Recommended Response Action: View successful pending operations by clicking the Pending Operations button.
Category: Configuration (RAC = RAC Event)
Severity: Severity 1 (Critical)
: No alerts are applicable for this message

RAC0687

Message: Some of the applied pending operations were not created.
Detailed Description: Some of the applied pending operations were not created.
Recommended Response Action: Choose to create a job for the successful operations. View successful pending operations using the Pending Operations button or click Cancel to quit job creation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 1 (Critical)
: No alerts are applicable for this message

RAC0688

Message: Applying this configuration operation will also apply all existing pending operations on the arg1 . #{View Pending Operations link}
Arguments: arg1 = controller_name
Detailed Description: Applying this configuration operation will also apply all existing pending operations on the controller identified in the message.
Recommended Response Action: Click Create Job button to create the configuration job. Click Cancel to quit job creation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0689

Message: Unable to create a virtual disk on the selected disk drives, because Lifecycle Controller is not enabled.
Detailed Description: Unable to create a virtual disk on the selected disk drives, because Lifecycle Controller is not enabled.
Recommended Response Action: To enable Lifecycle Controller, reboot the server. During server startup, press F2 to enter System Setup. Go to iDRAC Settings -> Lifecycle Controller, select Enable, and save the changes. Retry the operation after the server has restarted.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC069

Message: Unable to complete the operation because the string length is less than the minimum supported length.
Detailed Description: Unable to complete the operation because the string length is less than the minimum supported length.
Recommended Response Action: Enter a string value that is greater than the minumum supported length and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0690

Message: The iDRAC Service Module is not installed on the operating system of the server.
Detailed Description: The iDRAC Service Module is not installed on the operating system of the server.
Recommended Response Action: Install the iDRAC Service Module and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0692

Message: Unable to assign and un-assign physical disk drives as global hotspare(s), because Lifecycle Controller is not enabled.
Detailed Description: Unable to assign and un-assign physical disk drives as global hotspare(s), because Lifecycle Controller is not enabled.
Recommended Response Action: To enable Lifecycle Controller, reboot the server. During server startup, press F2 to enter System Setup. Go to iDRAC Settings -> Lifecycle Controller, select Enable, and save the changes. Retry the operation after the server has restarted.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0693

Message: Pending operations are created for the selected operations on the selected physical disk drives.
Detailed Description: Pending operations are created for the selected operations on the selected physical disk drives.
Recommended Response Action: To view the pending operations, click the Pending Operations button.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0694

Message: Unable to configure the attributes of the selected controller, because Lifecycle Controller is not enabled.
Detailed Description: Unable to configure the attributes of the selected controller, because Lifecycle Controller is not enabled.
Recommended Response Action: To enable Lifecycle Controller, reboot the server. During server startup, press F2 to enter System Setup. Go to iDRAC Settings -> Lifecycle Controller, select Enable, and save the changes. Retry the operation after the server has restarted.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0695

Message: Unable to perform security key operations on the selected controller, because Lifecycle Controller is not enabled.
Detailed Description: Unable to perform security key operations on the selected controller, because Lifecycle Controller is not enabled.
Recommended Response Action: To enable Lifecycle Controller, reboot the server. During server startup, press F2 to enter System Setup. Go to iDRAC Settings -> Lifecycle Controller, select Enable, and save the changes. Retry the operation after the server has restarted.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0696

Message: Unable to retrieve the hardware overview information because the server is turned off.
Detailed Description: The iDRAC is unable to retrieve hardware overview related information while the server is turned off.
Recommended Response Action: Turn the server on to view the hardware overview information.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0697

Message: Choose to create a job from the existing successfull pending operations.
Detailed Description: Choose to create a job from the existing successfull pending operations.
Recommended Response Action: Do one of the following: 1) Click Pending Operations button to view pending operations. 2) Click Create Job button to create a configuration job. 3) Click Cancel button to quit job creation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 1 (Critical)
: No alerts are applicable for this message

RAC0698

Message: Unable to modify USB management settings because the USB device is currently in use.
Detailed Description: Unable to modify USB management settings because the USB device is currently in use.
Recommended Response Action: Wait for the current USB operations to complete and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 1 (Critical)
: No alerts are applicable for this message

RAC0699

Message: Invalid value for Minimum Fan Speed.
Detailed Description: The value for Minimum Fan Speed must be within the range identified in the Recommended Response Action.
Recommended Response Action: Enter a value between <min>-<max>.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC070

Message: The SSL Web-Server certificate was successfully restored to factory defaults.
Detailed Description: The SSL Web-Server certificate was successfully restored to factory defaults.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0700

Message: Email page successful to arg1 .
Arguments: arg1 = email address
Detailed Description: An email page was successfully sent.
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0701

Message: Requested system powerup.
Detailed Description: Requested system powerup.
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0702

Message: Requested system powercycle.
Detailed Description: Requested system powercycle.
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0703

Message: Requested system hardreset.
Detailed Description: Requested system hardreset.
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0704

Message: Requested system powerdown.
Detailed Description: Requested system powerdown.
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0705

Message: Requested system graceful shutdown.
Detailed Description: Requested system graceful shutdown.
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0706

Message: Requested system NMI.
Detailed Description: Requested system NMI.
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0707

Message: Primary Firmware image is invalid. Currently booted from backup image. To restore primary image, update the firmware.
Detailed Description: Primary Firmware image is invalid. Currently booted from backup image. To restore primary image, update the firmware.
Recommended Response Action: Acquire an iDRAC firmware image of the version desired. Using the latest version available is recommended. Update the iDRAC firmware.
Category: Updates (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0708

Message: Previous reboot was due to a firmware watchdog timeout.
Detailed Description: Previous reboot was due to a firmware watchdog timeout.
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0709

Message: Unknown server inserted into chassis.
Detailed Description: Unknown server inserted into chassis.
Recommended Response Action: Acquire the latest Chassis Management Controller (CMC) firmware that supports the server indicated and update the CMC to at least that version.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC071

Message: Unable to perform the iDRAC reset operation because the firmware upgrade operation is in progress.
Detailed Description: The iDRAC reset operation cannot be completed because a firmware upgrade operation is in progress.
Recommended Response Action: Wait for the current update process to complete and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0710

Message: Server link tuning error.
Detailed Description: Server link tuning error.
Recommended Response Action: Ensure that the IO Module (IOM) and Mezzanine (Mezz) cards are appropriately matched. Check the M1000e Hardware Manual for correct component compatibility.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0711

Message: Unknown power on response from the CMC.
Detailed Description: Unknown power on response from the CMC.
Recommended Response Action: Try reseting the CMC. Also try reseating the server.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0712

Message: Server failed to power up due to zero power allocated.
Detailed Description: Server failed to power up due to zero power allocated.
Recommended Response Action: Utilize the Chassis Management Controller web interface to check available power and server power requirements. If sufficient power is available, allocate power necessary and retry the operation.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0713

Message: Server failed to power up due to fabric mismatch.
Detailed Description: Server failed to power up due to fabric mismatched.
Recommended Response Action: Ensure that the hardware comtibility between the IO Module (IOM) and the Mezzanine (Mezz) card is correct. Check the M1000e Hardware Manual for correct component compatibility.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0714

Message: Server failed to power up due to noncontinuous power action.
Detailed Description: Server failed to power up due to noncontinuous power action.
Recommended Response Action: Utilize the Chassis Management Controller web interface to check available power and server power requirements. If sufficient power is available, allocate power necessary and retry the operation.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0715

Message: Image file does not exist in the given remote share path.
Detailed Description: Image file does not exist in the given remote share path.
Recommended Response Action: Ensure that the image file is available on the share path provided. Retry the operation.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0716

Message: Unable to unmount remote share.
Detailed Description: Unable to unmount remote share.
Recommended Response Action: Retry the operation.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0717

Message: Remote share unmounted successfully.
Detailed Description: Remote share unmounted successfully.
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0718

Message: Remote File Share service is busy with the previous connection.
Detailed Description: Remote File Share service is busy with the previous connection.
Recommended Response Action: Stop the Remote File Share session and retyr the operation.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0719

Message: Not able to connect to remote file share. Virtual media devices are already in use.
Detailed Description: Not able to connect to remote file share. Virtual media devices are already in use.
Recommended Response Action: Stop existing Virtual Media sessions and retry the operation.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC072

Message: Unable to perform the iDRAC reset to factory defaults operation because the firmware upgrade is in progress.
Detailed Description: The iDRAC reset to factory defaults operation cannot be completed because a firmware upgrade operation is in progress.
Recommended Response Action: Wait for the current update process to complete and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0720

Message: Unable to mount remote share arg1 .
Arguments: arg1 = sharename
Detailed Description: Unable to mount remote share.
Recommended Response Action: Retry the operation.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0721

Message: Remote share mounted successfully arg1 .
Arguments: arg1 = sharename
Detailed Description: Remote share mounted successfully.
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0722

Message: Failed to program the Chassis assigned MAC address for the NIC.Integrated. arg1 .
Arguments: arg1 = NDC slot number
Detailed Description: Failed to program the Chassis assigned MAC address for the NIC.Integrated in the specified slot number.
Recommended Response Action: Reseat the server and retry.
Category: Audit (RAC = RAC Event)
Severity: Severity 1 (Critical)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0723

Message: The firmware version arg1 of the Chassis Management Controller is earlier than the required version arg2 .
Arguments: arg1 = version number, arg2 = version number
Detailed Description: The Chassis Management Controller firmware version identified in the message is earlier than the version required to support the server.
Recommended Response Action: Update the Chassis Management Controller firmware to the required version identified in the message.
Category: Audit (RAC = RAC Event)
Severity: Severity 1 (Critical)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC			✔*		✔*	✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*		✔*
CMC

RAC0724

Message: Quick Sync Firmware is successfully updated.
Detailed Description: Quick Sync Firmware is successfully updated.
Recommended Response Action: No response action is required.
Category: Updates (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC						✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0725

Message: Unable to update the Quick Sync Firmware.
Detailed Description: Unable to update the Quick Sync Firmware.
Recommended Response Action: No response action is required.
Category: Updates (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC						✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0726

Message: Auto-throttling is disabled for the server.
Detailed Description: Auto-throttling is disabled for the server based on a request from the Chassis Management Controller (CMC) because the CMC is restarting..
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔	✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0727

Message: Auto-throttling is enabled for the server.
Detailed Description: Auto-throttling is enabled for the server based on a request from the Chassis Management Controller (CMC) because the CMC has restarted.
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔	✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC0728

Message: The Quick Sync communication is no longer functioning.
Detailed Description: The Quick Sync communication or the connection to the iDRAC is no longer functioning.
Recommended Response Action: Do the following: 1) Remove and reseat the bezel. 2) Turn the bezel on by pressing the activation button. 3) Try the Quick Sync feature again. If the issue persists, contact your technical support provider.
Category: System Health (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔	✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC073

Message: Unable to perform the iDRAC reset operation because a vFlash partition creation operation is in progress.
Detailed Description: The iDRAC reset operation cannot be completed because a vFlash partition creation operation is in progress.
Recommended Response Action: Wait for the vFlash partition creation process to complete and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC074

Message: Unable to perform the iDRAC reset to factory defaults operation because a vFlash partition creation operation is in progress.
Detailed Description: The iDRAC reset to factory defaults operation cannot be completed because a vflash partition creation operation is in progress.
Recommended Response Action: Wait for the vFlash partition creation process to complete and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0740

Message: The Prepare to Remove operation will stop any activity on the PCIe SSD device so that it can be removed safely. The device is safe to remove when the disk shows the safe to remove LED pattern.
Detailed Description: The Prepare to Remove operation will stop any activity on the PCIe SSD device so that it can be removed safely. The device is safe to remove when the disk shows the safe to remove LED pattern.
Recommended Response Action: Press OK to continue.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0741

Message: Unable to perform Prepare to Remove or Secure Erase operations on the selected PCIe SSD disk drive(s), because Lifecycle Controller is not enabled.
Detailed Description: Unable to perform Prepare to Remove or Secure Erase operations on the selected PCIe SSD disk drive(s), because Lifecycle Controller is not enabled.Retry the operation after the server has restarted.
Recommended Response Action: To enable Lifecycle Controller, reboot the server. During server startup, press F2 to enter System Setup. Go to iDRAC Settings -> Lifecycle Controller, select Enable, and save the changes. Retry the operation after the server has restarted.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0742

Message: The Secure Erase command will be executed on the selected PCIe SSD disk drives(s) only after the reboot of the system or loss of power to the disk drives(s).
Detailed Description: A Secure Erase operation on a PCIe SSD overwrites all blocks in an encrypted way and all the data on the PCIe SSD device will be permanently lost. The changes will happen after reboot of the system or loss of power to the drive.
Recommended Response Action: Press OK to continue.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0743

Message: Unable to perform storage configuration operations because no storage controllers are detected on the server.
Detailed Description: Unable to perform storage configuration operations because no storage controllers are detected on the server
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0744

Message: Unable to perform storage configuration operations because neither Storage controllers nor PCIe Extenders detected on the system.
Detailed Description: Unable to perform storage configuration operations because neither Storage controllers nor PCIe Extenders detected on the system.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0745

Message: There are no pending operations present on the selected component group.
Detailed Description: There are no pending operations on the selected component group.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0746

Message: Unable to perform virtual disk (VD) operations, because Lifecycle Controller is not enabled.
Detailed Description: Unable to perform virtual disk(VD) operations, because Lifecycle Controller is not enabled.
Recommended Response Action: Enable the Lifecycle Controller and retry the operation. To enable Lifecycle Controller, restart the server. During server startup, press F2 to enter System Setup. Go to iDRAC Settings -> Lifecycle Controller, select Enable, and save the changes.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0747

Message: Unable to perform reset configuration on the selected controller, because Lifecycle Controller is not enabled.
Detailed Description: Unable to perform reset configuration on the selected controller, because Lifecycle Controller is not enabled.
Recommended Response Action: Enable the Lifecycle Controller and retry the operation. To enable Lifecycle Controller, reboot the server. During server startup, press F2 to enter System Setup. Go to iDRAC Settings -> Lifecycle Controller, select Enable, and save the changes.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0748

Message: The BIOS watchdog timer must be disabled if the Automatic System Recovery option is enabled.
Detailed Description: The BIOS watchdog must be disabled if Automatic System Recovery option is enabled.
Recommended Response Action: Make sure the BIOS watchdog timer is disabled before enabling the Automatic System Recovery option.
Category: Configuration (RAC = RAC Event)
Severity: Severity 1 (Critical)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔	✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC0749

Message: SNMPv3 User cannot be set to None.
Detailed Description: SNMPv3 User cannot be set to None.
Recommended Response Action: Set the SNMPv3 User to a value other than None and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔	✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC0750

Message: Unable to access the USB NIC IP address by using PING process.
Detailed Description: The USB NIC IP address cannot be accessed by using the PING process.
Recommended Response Action: Enter another appropriate IP address, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔	✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC0751

Message: The threshold value entered is less than the lower warning or critical threshold.
Detailed Description: The value for information or warning threshold should not be less than lower critical threshhold value.
Recommended Response Action: Enter a threshold value that is greater than the lower warning or critical threshold values and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0752

Message: The threshold value entered is greater than the upper warning or critical threshold.
Detailed Description: The value for information or warning threshold should not be greater than upper critical threshold value.
Recommended Response Action: Enter a threshold value that is lower than the upper warning or critical threshold values and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0753

Message: Reset iDRAC to apply the pending new certificate. Until iDRAC is reset the old certificate will be active.
Detailed Description: Reset iDRAC to apply the pending new certificate. Until iDRAC is reset old certificate will be active. A manual reset of iDRAC is needed for the new certificate to take into effect.
Recommended Response Action: Click the Reset iDRAC link to reset iDRAC.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0754

Message: Reset iDRAC to complete the deletion action of the certificate.
Detailed Description: Reset iDRAC to complete custom SSL certificate deletion action. A manual reset of iDRAC is needed for the action to take effect.
Recommended Response Action: Click the Reset iDRAC link to reset iDRAC.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0755

Message: The selected value is not supported on this server.
Detailed Description: The selected value is not supported on this server.
Recommended Response Action: Retry the operation with another value.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0756

Message: Unable to retrieve the fan information.
Detailed Description: Fan information cannot be displayed. This situation may occur if the server is powered off.
Recommended Response Action: Power on the server. If the server is already powered on, wait for a few minutes and refresh the page. If the problem persists, contact your service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0757

Message: USB Management Port is currently disabled in BIOS configuration.
Detailed Description: The requested operation using the USB Management Port cannot be completed because the port is disabled in BIOS configuraton.
Recommended Response Action: Enable the USB Management Port in BIOS configuration to use this feature
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0758

Message: Tech Support Report (TSR) data is being collected. This operation will take less than arg1 minutes.
Arguments: arg1 = collection time
Detailed Description: The Tech Support Report generation will take the time identified in the message to complete.
Recommended Response Action: To cancel the reports collection click Cancel.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0759

Message: A running Tech Support Report job has been cancelled.
Detailed Description: A running Tech Support Report job has been cancelled.
Recommended Response Action: Click Job Queue button to view the status of the cancelled job.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0760

Message: Unable to perform physical disk(s) storage configuration operations for the selected controller.
Detailed Description: Unable to perform storage configuration operations on physical disk drive(s) as there are no disk drive(s) available with Ready/RAID/NON-RAID state or the selected controller is in HBA mode.
Recommended Response Action: Check the following: 1) If there are no physical disk drive(s) in either Ready state or in RAID/NON-RAID state, insert additional disk drive(s). 2) If the Controller(s) are in HBA mode, switch the controller(s) to RAID mode. To switch controller(s) to RAID mode using the F2 System Setup utility, go to Device Settings > RAID Controller > Controller Management > Advanced Controller Management > Switch to RAID mode.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0761

Message: Unable to retrieve system inventory.
Detailed Description: The system inventory cannot be retrieved because another system inventory operation may already be in progress or due to an internal issue whether or not Collect System Inventory On Restart (CSIOR) is enabled or disabled.
Recommended Response Action: A system inventory operation may be in progress. Wait for the operation to complete and retry the operation. If no other system inventory operation is in progress, enable the Collect System Inventory On Restart (CSIOR) feature, reboot the system, and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0762

Message: Unable to perform a firmware update because a valid catalog file is not available on the network share.
Detailed Description: Unable to perform a firmware update because a valid catalog file is not available on the network share.
Recommended Response Action: Make sure that a valid catalog file is available on the network share and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔	✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC0763

Message: Unable to configure the port number that is entered because the port number is already in use.
Detailed Description: Unable to configure the port number that is entered because the port number is already in use.
Recommended Response Action: Enter a port number that is not already in use and retry the operation. If the issue persists, contact your service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔	✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC0764

Message: Selecting a higher SSL encryption enhances the security. However, the cryptography settings for your virtual machine environment (JVM, IcedTea) may require installing the Unlimited Strength Java Cryptography Extension Policy Files to permit usage of iDRAC plugins such as vConsole with this higher level of encryption. NOTE: Using this level of encryption may have import or export implications. For more guidance, contact your legal department.
Detailed Description: Selecting a higher SSL encryption enhances the security. However, the cryptography settings for your virtual machine environment (JVM, IcedTea) may require installing the Unlimited Strength Java Cryptography Extension Policy Files to permit usage of iDRAC plugins such as vConsole with this higher level of encryption. NOTE: Using this level of encryption may have import or export implications. For more guidance, contact your legal department.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔	✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC0765

Message: Unable to access the operating system (OS) IP address by using the Ping process because an incorrect IP address is entered.
Detailed Description: The OS IP address cannot be accessed by using the Ping process because an incorrect IP address is entered.
Recommended Response Action: Enter a correct IP address, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0766

Message: Unable to assign USB NIC IP address arg1 to the OSBMC device because only Link Local IP address can be allowed.
Arguments: arg1 = IP address
Detailed Description: The USB NIC IP address identified in the message cannot be assigned to the OSBMC device because only Link Local IP address can be allowed.
Recommended Response Action: Enter appropriate Link Local IP address, and then retry the operation. For information about supported IP addresses, refer to the iDRAC Users Guide available at the support site.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0767

Message: Unable to assign USB NIC IP address arg1 to the OSBMC device because IP address setting conflicts with existing network interface IP.
Arguments: arg1 = IP address
Detailed Description: The USB NIC IP address identified in the message cannot be assigned to the OSBMC device because IP address setting conflicts with existing network interface IP.
Recommended Response Action: Enter an unique IP address for OSBMC USB NIC that is not the same as another NICs IP address, and then retry the operation. For information about supported IP addresses, refer to the iDRAC Users Guide available at the support site.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0801

Message: iDRAC has reset to default settings.
Detailed Description: iDRAC closes all the existing sessions and all configuration settings are set to default values. The iDRAC IP address is set to the default static IP address.
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔
CMC

RAC0901

Message: Invalid syntax. The -t option value must set to 1.
Detailed Description: The syntax of the specified command is invalid. In this case, the usage of the -t option is invalid.
Recommended Response Action: See the help text/documentation for the valid syntax of the subcommand.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0902

Message: The -f option requires -d to also be specifed.
Detailed Description: The syntax of the specified command is invalid. In this case, the usage of the -f option is invalid.
Recommended Response Action: See the help text/documentation for the valid syntax of the subcommand.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0903

Message: The -d option cannot be used with any other options.
Detailed Description: The syntax of the specified command is invalid. In this case, the usage of the -d option is invalid.
Recommended Response Action: See the help text/documentation for valid syntax of the subcommand.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0904

Message: The remote file location is not accessible or reachable.
Detailed Description: The iDRAC cannot access the remote file location. The credentials or path to the remote file location is incorrect or iDRAC cannot connect to the network address.
Recommended Response Action: Confirm that the path and credentials to remote file are correct, and check that the iDRAC can connect to the network address.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0905

Message: Failed to get the USC version details.
Detailed Description: Unable to obtain the USC version details.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0906

Message: Operation failed.
Detailed Description: Unable to perform the requested operation.
Recommended Response Action: Try again later. If the problem persists, contact technical support. Refer to your product documentation to choose the contact method.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0907

Message: System ID LED blink on.
Detailed Description: The System ID LED was successfully set to on.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC0908

Message: System ID LED blink off.
Detailed Description: The System ID LED was successfully set to off.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0909

Message: Invalid subcommand syntax: Specify the object name.
Detailed Description: The specified command is missing object name syntax.
Recommended Response Action: Specify the correct subcommand object name syntax. See the help text or documentation for valid syntax.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0910

Message: Invalid subcommand syntax: Specify group and object name.
Detailed Description: The specified command is missing group and object name syntax.
Recommended Response Action: Specify the correct subcommand group and object name syntax. See the help text or documentation for the valid syntax.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0911

Message: Data about version details is unavailable.
Detailed Description: Unable to retrieve version details.
Recommended Response Action: Try again later. If the problem persists, contact technical support. Refer to your product documentation to choose the contact method that is convenient for you.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC0912

Message: Unable to connect to RAC at specified IP address.
Detailed Description: The management system could not connect to the iDRAC.
Recommended Response Action: Verfiy whether the IP address of the remote iDRAC is correct. Verify whether connectivity exists between the management system and the iDRAC.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC1000

Message: Unable to set the object value for iDRAC IPv6 address or gateway.
Detailed Description: Unable to set the object value for iDRAC IPv6 Address1 and IPv6 Gateway, because the object IPv6 Autoconfig is enabled.
Recommended Response Action: Disable the object IPv6 AutoConfig using "racadm set iDRAC.IPv6.AutoConfig <0 | Disabled >", and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1001

Message: Unable to set the object value for iDRAC IPv6 DNS1 or DNS2.
Detailed Description: Unable to set the object value for iDRAC IPv6 DNS1 or DNS2, because the object DNSFromDHCP6 is enabled.
Recommended Response Action: Disable the object DNSFromDHCP6 using "racadm set iDRAC.IPv6.DNSFromDHCP6 <0 | Disabled>", and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1002

Message: Active Directory Single Sign On (SSO) cannot be enabled.
Detailed Description: The Active Directory SSO cannot be enabled, because the object SmartCardLogonEnable is enabled.
Recommended Response Action: Disable the object SmartCardLogonEnable using "racadm set iDRAC.SmartCard.LogonEnable <0 | Disabled>", and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1003

Message: The smart card certificate revocation list (CRL) cannot be enabled.
Detailed Description: The smart card certificate revocation list (CRL) cannot be enabled, because the object SmartCardLogonEnable is disabled.
Recommended Response Action: Enable the object SmartCardLogonEnable using "racadm set iDRAC.SmartCard.SmartCardLogonEnable <1 | Enabled>", and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1004

Message: The smart card login cannot be enabled.
Detailed Description: The smart card login cannot be enabled, because the Active Directory Single Sign On is enabled.
Recommended Response Action: Disable Active Directory Single Sign On (SSO) using "racadm set iDRAC.ActiveDirectory.SSOEnable <0 | Disabled>", and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1005

Message: Successfully exported hardware inventory.
Detailed Description: The hardware inventory was successfully exported.
Recommended Response Action: No response action is required
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1006

Message: Unable to process the arg1 , and the update was not applied.
Arguments: arg1 = file name
Detailed Description: The update was not applied because of one of the following reasons: 1) The Update Package is invalid. 2) Lifecycle Controller is corrupted. 3) Another update is in progress.
Recommended Response Action: Do one of the following and retry the operation: 1) Dowload the correct Update Package from your service provider. 2) Use the Lifecycle Controller repair package to repair Lifecycle Controller. For more information, see Lifecycle Controller Users Guide. 3) Wait until the current update operation is complete.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1007

Message: The job arg1 cannot be deleted.
Arguments: arg1 = job ID
Detailed Description: The job specified in the meesage cannot be deleted when it is Running, Scheduled, or tranitioniong from Downloading to Scheduled.
Recommended Response Action: Wait until the specified job is completed, or reboot the system to move the job to Completed state. To view the job status, use "racadm jobqueue view -i <Job_ID>".
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1008

Message: The Active Directory object DCLookupByUserDomain cannot be disabled.
Detailed Description: The Active Directory object DCLookupByUserDomain cannot be disabled, because the Active Directory object DCLookupDomainName is not configured.
Recommended Response Action: Configure the Active Directory object DCLookupDomainName using "racadm set iDRAC.ActiveDirectory.DCLookupDomainName <Name>", and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1009

Message: The Active Directory objects DCLookupEnable or GCLookupEnable cannot be enabled.
Detailed Description: The Active Directory objects DCLookupEnable or GCLookupEnable cannot be enabled, because IPv4.DNS1, IPv4.DNS2, IPv6.DNS1, or IPv6.DNS2 is not configured.
Recommended Response Action: Configure IPv4.DNS1, IPv4.DNS2, IPv6.DNS1, or IPv6.DNS2 using racadm set command, and retry the operation. For example, "racadm set iDRAC.IPv4.DNS1 <address>".
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1010

Message: Unable to set the power cap value.
Detailed Description: The power cap cannot be set if the object Power.Cap is disabled.
Recommended Response Action: Enable Power Cap setting using "racadm set System.Power.Cap.Enable < 1 | Enabled >", and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1011

Message: The OS to iDRAC pass-through cannot be enabled.
Detailed Description: The OS to iDRAC pass-through cannot be enabled, because the NIC is in Dedicated mode.
Recommended Response Action: Change the iDRAC NIC mode to shared mode using "racadm set idrac.nic.selection <value>", and retry the opeation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1012

Message: Unable to change the auto-negotiation state for the current NIC selection mode.
Detailed Description: Unable to change the auto-negotiation state for the current NIC selection mode, because the iDRAC NIC is in dedicated mode.
Recommended Response Action: Change the iDRAC NIC mode to shared mode using "racadm set idrac.nic.selection <value>", and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1013

Message: The SNMPv3 authentication protocol state cannot be set to None if the SNMPv3 privacy protocol state is set to None.
Detailed Description: For any iDRAC user, SNMPv3 authentication protocol can be changed to "None" only if the SNMPv3 privacy protocol state is set to "None".
Recommended Response Action: Change the SNMPv3 privacy protocol state to None using "racadm set iDRAC.Users.<index>.SNMPv3PrivacyType none", and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1014

Message: The SNMPv3 privacy protocol cannot be configured to AES or DES mode if SNMPv3 authentication protocol state is set to "None".
Detailed Description: The SNMPv3 privacy protocol cannot be configured to AES or DES mode if SNMPv3 authentication protocol state is set to "None".
Recommended Response Action: To configure the SNMPv3 Privacy Protocol for a specified iDRAC user, change the SNMPv3 Authentication Protocol to either MD5 or SHA state using "racadm set idrac.users.<index>.SNMPv3AuthenticationType <value>".
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1016

Message: The specified user already exists. Duplicate user names are not allowed.
Detailed Description: iDRAC does not allow duplicate user names for each of the 16 users.
Recommended Response Action: Make sure that each of the 16 user names are unique.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1017

Message: Successfully modified the object value and the change is in pending state.
Detailed Description: Any staged operation requires a job and system reboot to apply the object values.
Recommended Response Action: To apply modified value, create a configuration job and reboot the system. To create the commit and reboot jobs, use "jobqueue" command. For more information about the "jobqueue" command, see RACADM help.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1018

Message: The specified object or syntax is invalid.
Detailed Description: This occurs when an incorrect syntax is used or an incorrect object is specified during the command invocation.
Recommended Response Action: Make sure to use the correct syntax and correct object names, and retry the operation. For information related to the corresponding group, see RACADM help or the RACADM Users Guide.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1019

Message: The specified object is not supported for the current system configuration.
Detailed Description: Some objects have dependencies on other objects that are required to perform a task. The specified object is not available because of such dependencies.
Recommended Response Action: Verify the object dependency using "racadm help <device class>.<groupname>.<objectname>", and retry the operation. For example, racadm help NIC.VndrConfigGroup.1.VirtWWPN.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1020

Message: No objects are available under the specified group for the current system configuration.
Detailed Description: Some objects have dependencies on other objects that are required to perform a task. The specified group does not contain any objects, because the dependent objects are not part of the current system configuration.
Recommended Response Action: Verify the dependencies of the objects under the specified group using "racadm help <device class>.<groupname>", and retry the operation. For example, "racadm help NIC.IscsiSecondTgtParams".
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1021

Message: NIC objects are not available in the current system configuration.
Detailed Description: NIC objects are not available if NIC devices are not installed in the system, or if some iDRAC services are busy.
Recommended Response Action: Make sure the NIC devices are correctly installed in the system and retry the operation after the Collect System Inventory On Restart (CSIOR) feature has updated the system inventory. If the issue persists, contact your service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1023

Message: Unable to create the configuration job.
Detailed Description: Configuration jobs are created only if at least one object on the device or component (for example, NIC.Slot.1 or BIOS) has a pending value to be applied.
Recommended Response Action: Make sure that there is at least one object on the specified device or component that has a pending vlaue, and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1024

Message: Successfully scheduled a job.
Detailed Description: The pending value is applied during the next reboot of system.
Recommended Response Action: Verify the job status using "racadm jobqueue view -i JID_xxxxx" command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1025

Message: The specified object is read-only and cannot be modified due to an object dependency.
Detailed Description: Some objects have dependencies on other objects that are required to perform a task. However, some of the objects are read-only because of the current system configuration and the values of the dependent objects.
Recommended Response Action: Verify the object dependency using "racadm help <device class>.<groupname>.<objectname>", and retry the opearation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1026

Message: A custom signing certificate does not exist.
Detailed Description: A custom signing certificate must be present in the system to delete or downlod the certificate.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1027

Message: Successfully sent the alert for the specified event to the configured destination.
Detailed Description: A test event was generated and the alert was successfully sent to the destination.
Recommended Response Action: Verify if the alerts were received by the configured tdestination. Otherwise, reconfigure the destination and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1028

Message: Unable to download the specified certificate type.
Detailed Description: The certificate cannot be downloaded if the certificate type specified is other than "1", "2", or "3".
Recommended Response Action: Make sure to specify either "1", "2", or "3" for the certificate type (-t) option, and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1029

Message: Unable to delete the specified certificate type.
Detailed Description: The certificate cannot be deleted if the certificate type specified is not "3".
Recommended Response Action: Make sure to specify "3" for the certificate type (-t) option, and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1030

Message: The custom signing certificate was deleted.
Detailed Description: The custom signing certificate present on iDRAC was deleted.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1031

Message: Unable to delete the custom signing certificate.
Detailed Description: The custom signing certificate on iDRAC cannot be deleted because of an internal error.
Recommended Response Action: Verify if iDRAC has a custom signing certificate. If it has the certificate, retry the operation. If the issue persists, contact your service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1032

Message: arg1 jobs was cancelled by the user.
Arguments: arg1 = Job ID or ALL
Detailed Description: The job specified in the message were cancelled.
Recommended Response Action: No response action is required
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1033

Message: Unable to retrieve the server component software inventory.
Detailed Description: The server component software inventory cannot be retrieved because of an internal error.
Recommended Response Action: Make sure to enable Collect System Inventory On Restart (CSIOR) feature, reboot the server, and retry the operation. If CSIOR is already enabled, restart iDRAC using "racadm racreset" command, and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1034

Message: This action will ungracefully turn off the server.
Detailed Description: This operation will cause the server to shutdown immediately. This may result in the applications losing data.
Recommended Response Action: Before continuing, exit all the programs running on this server, and make sure that there is no inbound and outbound traffic associated with this server. Inability to do so may prevent all the servers in the chassis from accessing the shared-storage devices for up to two minutes. To continue the operation, enter a -f at the end of command "racadm serveraction powerdown -f", and then retry.
Category: System Health (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1035

Message: There are no pending values to be cleared.
Detailed Description: The command is unable to clear the pending state for attributes of the specified component because there are no pending values.
Recommended Response Action: Make sure that there is at least one attribute on the specified device has a pending value, and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC1036

Message: Successfully cleared pending attribute(s) for the group specified.
Detailed Description: Successfully cleared pending values for attributes in the group specified.
Recommended Response Action: To verify, run the RACADM command "racadm get group".
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC1037

Message: Unable to clear pending attribute(s).
Detailed Description: Unable to clear pending attribute(s). This may be because the FQDD entered is incorrect.
Recommended Response Action: Check that the FQDD entered is correct. View the Help information by running the RACADM command "racadm help clearpending".
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1038

Message: Unable to clear pending values for the specified component.
Detailed Description: Unable to clear pending values for the specified component. This may be because there is an existing configuration job for the component.
Recommended Response Action: Make sure that a config job is not scheduled for this component. For more information, view the help command by running the RACADM command "racadm jobqueue help delete".
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1039

Message: The subcommand entered is not supported on the specified server.
Detailed Description: The subcommand entered is not supported on the specified server.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1040

Message: Successfully accepted the RAID storage configuration operation. The change is in pending state.
Detailed Description: The requested RAID storage operation was successfully accepted and now must be applied by creating a RAID storage configuration job.
Recommended Response Action: To apply the configuration operation, create a configuration job, and then restart the server. To create the required commit and reboot jobs, run the jobqueue command. For more information about the jobqueue command, enter the RACADM command "racadm help jobqueue".
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC1041

Message: Successfully configured the Automatic Update (autoupdate) feature settings.
Detailed Description: Successfully configured the Automatic Update (autoupdate) feature settings.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1042

Message: Unable to configure the Automatic Update (autoupdate) feature settings. The required options are either invalid or not provided.
Detailed Description: One or more required options to configure the Automatic Update (autoupdate) feature are missing.
Recommended Response Action: For more information, view the help details by running the RACADM command "racadm help autoupdatescheduler".
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1043

Message: Unable to configure the Automatic Update (autoupdate) feature settings. The option arg1 is either invalid or not provided.
Arguments: arg1 = option name
Detailed Description: The operation did not complete successfully because of an invalid value for the option identified in the message.
Recommended Response Action: Retry with a correct value for the option identified in the message. For more information, view the help details by running the RACADM command "racadm help autoupdatescheduler".
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1044

Message: The Automatic Update (autoupdate) feature is not enabled.
Detailed Description: The Automatic Update (autoupdate) feature is not enabled
Recommended Response Action: To enable, run the RACADM command "racadm set lifecyclecontroller.lcattributes.autoupdate 1".
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1045

Message: Specifying ftp.dell.com as the catalog source for the Automatic Update feaure may result in frequent system firmware updates because the catalog on ftp.dell.com changes often.
Detailed Description: Individual component firmware updates may occur frequently and cause changes to the catalog on ftp.dell.com. Specifying ftp.dell.com as the catalog source for the Automatic Update feaure may result in frequent system firmware updates.
Recommended Response Action: Creating a custom repository using the Repository Manager tool allows control of the frequency of component firmware updates.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1046

Message: Unable to view the Automatic Update (autoupdate) feature settings because the feature has not been configured.
Detailed Description: Unable to view the Automatic Update (autoupdate) feature settings because the feature has not been configured.
Recommended Response Action: Configure the Automatic Update feature by running the RACADM command "racadm autoupdatescheduler create" with the desired option settings.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1047

Message: Successfully cleared the Automatic Update (autoupdate) feature settings.
Detailed Description: Successfully cleared the Automatic Update(autoupdate) feature settings.
Recommended Response Action: No response action is required
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1048

Message: Unable to clear the Automatic Update (autoupdate) feature settings because there is currently no configuration.
Detailed Description: The Automatic Update (autoupdate) feature settings must already exist in order to be cleared.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1049

Message: Successfully configured the Automatic Backup (autobackup) feature settings.
Detailed Description: Successfully configured the Automatic Backup (autobackup) feature settings.
Recommended Response Action: No response action is required
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1050

Message: Unable to configure the Automatic Backup (autobackup) feature settings. The required options are either invalid or not provided.
Detailed Description: One or more required options to configure the Automatic Backup (autobackup) feature are missing.
Recommended Response Action: For more information, view the help details by running the RACADM command "racadm help systemconfig backup".
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1051

Message: Unable to configure the Automatic Backup (autobackup) feature settings. The option arg1 is either invalid or not provided.
Arguments: arg1 = option name
Detailed Description: The operation did not complete successfully because of an invalid value for the option identified in the message.
Recommended Response Action: Retry with a correct value for the option identified in the message. For more information, view the help details by running the RACADM command "racadm help systemconfig backup".
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1052

Message: The Automatic Backup (autobackup) feature is not enabled.
Detailed Description: The Automatic Backup (autobackup) feature is not enabled.
Recommended Response Action: To enable, run the RACADM command "racadm set lifecyclecontroller.lcattributes.autobackup 1".
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1053

Message: Unable to view the Automatic Backup (autobackup) feature settings because the feature has not been configured.
Detailed Description: Unable to view the Automatic Backup (autobackup) feature settings because the feature has not been configured.
Recommended Response Action: Configure the Automatic Backup feature by running the RACADM command "racadm systemconfig backup" with the desired option settings.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1054

Message: Successfully cleared the Automatic Backup (autobackup) feature settings.
Detailed Description: Successfully cleared the Automatic Backup (autobackup) feature settings.
Recommended Response Action: No response action is required
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1055

Message: Unable to clear the Automatic Backup (autobackup) feature settings because there is currently no configuration.
Detailed Description: The Automatic Backup (autobackup) feature settings must already exist in order to be cleared.
Recommended Response Action: No response action is required
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1056

Message: Rollback operation initiated successfully.
Detailed Description: The requested firmware Rollback operation was initiated successfully.
Recommended Response Action: No response action is required
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1057

Message: Rollback operation did not complete successfully. The component identifier specified is not valid or does not have a rollback firmware image available.
Detailed Description: Rollback operation did not complete successfully. The component identifier (FQDD) specified in the operation is not valid or does not have a Rollback firmware image available.
Recommended Response Action: Run the RACADM command "racadm swinventory" to see the list of Rollback firmware images available and the corresponding component identifier (FQDD).
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC1058

Message: Rollback operation did not complete successfully because Lifecycle Controller is disabled.
Detailed Description: The requested firmware Rollback operation did not complete successfully because Lifecycle Controller is disabled.
Recommended Response Action: Run the RACADM command "racadm set LifecycleController.LCAttributes.LifecycleControllerState 1" to enable Lifecycle Controller, and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1059

Message: Rollback operation could not be performed because another firmware update job is running.
Detailed Description: The requested firmware rollback operation could not be performed because another firmware update job is running or being scheduled.
Recommended Response Action: Wait until the existing firmware update jobs are completed or scheduled before retrying the operation. To monitor the status of the existing jobs, run the RACADM command "racadm jobqueue view". If the issue persists, restart the iDRAC and then retry the operation after the iDRAC has finished restarting.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1060

Message: System inventory may not becurrent because the Collect System Inventory On Restart (CSIOR) feature is disabled.
Detailed Description: The system inventory information may not be current because the Collect System Inventory On Restart (CSIOR) feature is disabled.
Recommended Response Action: To enable the CSIOR feature, run the RACADM command "racadm set LifecycleController.LCAttributes.CollectSystemInventoryOnRestart 1". Then restart the server to cause system inventory information to be collected.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1061

Message: SystemErase operation initiated successfully.
Detailed Description: The requested SystemErase operation was initiated successfully.
Recommended Response Action: Check the job status by running the RACADM command: "racadm jobqueue view -i <JobID>".
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1062

Message: Unable to initiate the SystemErase operation. The component identifier specified is not valid.
Detailed Description: Unable to initiate the requested SystemErase operation. The component identifier specified is not valid.
Recommended Response Action: Run the RACADM command "racadm help systemerase" to see the list of supported components.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1063

Message: Unable to initiate the SystemErase operation because Lifecycle Controller is disabled.
Detailed Description: Unable to initiate the SystemErase operation because Lifecycle Controller is disabled.
Recommended Response Action: Run the RACADM command "racadm set LifecycleController.LCAttributes.LifecycleControllerState 1" to enable Lifecycle Controller, and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1064

Message: Unable to initiate the SystemErase operation because another instance of SystemErase job is already in progress.
Detailed Description: Unable to initiate the requested SystemErase operation because another SystemErase job is already in progress.
Recommended Response Action: To check the job status, run the RACADM command "racadm jobqueue view" and retry the operation after the current SystemErase operation has completed.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1065

Message: Unable to initiate the SystemErase operation because iDRAC encountered an internal issue.
Detailed Description: Unable to initiate the SystemErase operation because iDRAC encountered an internal issue.
Recommended Response Action: Retry the operation. If the issue persists, restart the iDRAC and then retry the operation after the iDRAC has finished restarting.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1067

Message: Unable to set the minimum non critical threshold value of arg1 , because the value entered is lesser than, or equal to the minimum critical threshold value.
Arguments: arg1 = System Board Inlet Temp
Detailed Description: The minimum non critical threshold value identified in the message cannot be set, because the value entered is lesser than, or equal to the minimum critical threshold value.
Recommended Response Action: Check the minimum critical threshold level using an appropriate RACADM command. For example, to view the minimum threshold value of a sensor, run the racadm getsensorinfo command at the command line interface, and then retry the operation. For more information about other RACADM commands, run the racadm help command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC	✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1068

Message: Unable to set minimum non critical threshold value of arg1 , because the value entered is greater than, or equal to the maximum non critical threshold value.
Arguments: arg1 = System Board Inlet Temp
Detailed Description: The minimum non critical threshold value identified in the message cannot be set, because the value entered is greater than, or equal to the maximum non critical threshold value.
Recommended Response Action: Check the maximum non critical threshold level using an appropriate RACADM command. For example, to view the maximum non critical threshold value of a sensor, run the racadm getsensorinfo command at the command line interface, and then retry the operation. For more information about other RACADM commands, run the racadm help command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC	✔				✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1069

Message: Unable to set minimum non critical threshold value of arg1 , because the value entered is greater than, or equal to the maximum critical threshold value.
Arguments: arg1 = System Board Inlet Temp
Detailed Description: The minimum non critical threshold value identified in the message cannot be set, because the value entered is greater than, or equal to the maximum critical threshold value.
Recommended Response Action: Check the maximum critical threshold level using an appropriate RACADM command. For example, to view the maximum critical threshold value of a sensor, run the racadm getsensorinfo command at the command line interface, and then retry the operation. For more information about other RACADM commands, run the racadm help command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC	✔				✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1070

Message: Unable to set the maximum non critical threshold value of arg1 , because the value entered is greater than, or equal to the maximum critical threshold value.
Arguments: arg1 = System Board Inlet Temp
Detailed Description: The maximum non critical threshold value identified in the message cannot be set, because the value entered is greater than or equal to the maximum critical threshold value.
Recommended Response Action: Check the maximum critical threshold level using an appropriate RACADM command. For example, to view the maximum critical threshold value of a sensor, run the racadm getsensorinfo command at the command line interface, and then retry the operation. For more information about other RACADM commands, run the racadm help command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC	✔				✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1071

Message: Unable to set maximum non critical threshold value of arg1 , because the value entered is less than, or equal to the minimum non critical threshold value.
Arguments: arg1 = System Board Inlet Temp
Detailed Description: The maximum non critical threshold value identified in the message cannot be set, because the value entered is less than or equal to the minimum non critical threshold value.
Recommended Response Action: Check the minimum non critical threshold level using an appropriate RACADM command. For example, to view the minimum non critical threshold value of a sensor, run the racadm getsensorinfo command at the command line interface, and then retry the operation. For more information about other RACADM commands, run the racadm help command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC	✔				✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1072

Message: Unable to set maximum non critical threshold value of arg1 , because the value entered is less than, or equal to the minimum critical threshold value.
Arguments: arg1 = System Board Inlet Temp
Detailed Description: The maximum non critical threshold value identified in the message cannot be set, because the value entered is less than or equal to the minimum critical threshold value.
Recommended Response Action: Check the minimum critical threshold level using an appropriate RACADM command. For example, to view the minimum critical threshold value of a sensor, run the racadm getsensorinfo command at the command line interface, and then retry the operation. For more information about other RACADM commands, run the racadm help command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC	✔				✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1073

Message: Unable to reset the threshold value of sensor arg1 because the capability to reset this sensor threshold value is not supported.
Arguments: arg1 = sensor name
Detailed Description: The threshold value of the sensor identified in the message cannot be successfully set because the capability reset the sensor threshold value is not supported.
Recommended Response Action: No response action is required. For more information about resetting the threshold level of a sensor, run the "racadm getsensorinfo" command at the command line interface (CLI), and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC	✔				✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1109

Message: Unable to run the command, because an incorrect Share type is entered.
Detailed Description: Unable to run the command, because an incorrect Share type was entered.
Recommended Response Action: Enter an appropriate Share location of the following types: FTP, NFS, or CIFS. For more information, run the "racadm help update" command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1110

Message: Unable to run the command, because an incorrect Proxy port number was entered.
Detailed Description: Unable to run the command, because an incorrect Proxy port number was entered. The Proxy port value must be a positive integer.
Recommended Response Action: Enter only numbers for a Proxy port value.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1111

Message: Unable to delete the pending values or operations of the specified device.
Detailed Description: Unable to clear pending values or operations from the specified storage device because there are no pending operations for the specified device.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1112

Message: Unable to delete the pending values for the specified device because the iDRAC internal storage is in use by a currently running job.
Detailed Description: Unable to clear the pending state from the attributes for a RAID object. A job is currently running and iDRAC internal storage is in use.
Recommended Response Action: Retry the operation after any currently running jobs have completed. Jobs can be monitored by running the racadm command "racadm jobqueue view".
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1113

Message: Unable to perform the preview operation because the options -b, -c, -w, and -s must not be used with the --preview option.
Detailed Description: The configuration XML preview operation cannot be executed because the -b, -s, and -w options must not be used with the --preview option.
Recommended Response Action: Remove the -b, -w, and -s options wihen using the --preview option and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1114

Message: Configuration XML file preview operation job is initiated. Job ID = arg1
Arguments: arg1 = job ID
Detailed Description: The configuration XML preview operation was successfully initiatied and has generated a job with the job ID identified in the message.
Recommended Response Action: Monitor the status of the preview operation job by running the racadm command "racadm jobqueue view -i <job ID>".
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1115

Message: Unable to run the command, because of insufficient user privileges.
Detailed Description: The command could not be successfully run, because of insufficient privileges for the username supplied.
Recommended Response Action: Make sure that you have appropriate privileges, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1116

Message: Unable to run the command, because the restart flag entered is incorrect.
Detailed Description: The command could not be successfully run, because an incorrect "restart flag" value was entered in the command.
Recommended Response Action: Enter a correct flag value. The recommended values are "true" and "false". Make sure that you have entered the correct value, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1117

Message: Unable to run the command.
Detailed Description: The operation specified in the command could not be successfully completed.
Recommended Response Action: Retry the operation after 2 minutes. If the problem persists, contact your service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1118

Message: Successfully initiated the update operation specified in the command.
Detailed Description: Successfully initiated the update operation specified in the command.
Recommended Response Action: To know about the status of a command that is initiated, run the following command: racadm jobqueue view -I <job ID>.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1119

Message: Unable to generate a comparison report for the specified repository.
Detailed Description: The command could not be successfully run because of one or more of the following reasons: 1. The command does not have "--verifycatalog" in it. 2. The updates available on the repository are not applicable for the operation that is requested.
Recommended Response Action: To generate a comparison report, type "--verifycatalog" in the racadm command, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1120

Message: Unable to run the command, because an incorrect Proxy type is entered.
Detailed Description: The command could not be successfully run, because an incorrect Proxy type value was entered for the -pt option.
Recommended Response Action: Make sure that you entered either "http" or "https" as the proxy type. Enter the correct type, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1121

Message: Unable to run the command, because the data entered for connecting to the Proxy server is insufficient.
Detailed Description: The command could not be successfully run, because one or more values about the proxy server was not entered.
Recommended Response Action: Make sure that you enter the following data, and then retry the operation: - proxy server address - proxy user name - proxy password
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1122

Message: The specified group or object is not supported on the server.
Detailed Description: One or more of the group or component attributes specified in the operation do not exist on the targeted server.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1123

Message: Unable to perform the operation because Fibre Channel (FC) attributes are not available in the current server configuration.
Detailed Description: Fibre Channel (FC) objects are not available if Fibre Channel devices are not installed in the server, or if some iDRAC services are busy.
Recommended Response Action: Do the following: 1) Power off and remove AC or DC power from the server. 2) Make sure the Fibre Channel devices are correctly installed in the server. 3) Restart the server to allow the Collect System Inventory On Restart (CSIOR) feature to update the server inventory. 4) Retry the operation. If the issue persists, contact your service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1128

Message: The -l option must be specified if -u and -p options are used.
Detailed Description: Any operation involving remote share (CIFS) cannot continue if the location (-l option) is not specified. The -u and -p options represent the user name and password for the remote share, and -l represents the location of the remote share.
Recommended Response Action: Make sure to specify the location (-l option) of the remote share along with the user name and password, and retry the operation. To view the list of options that can used for the required subcommand, run the RACADM command "racadm help <subcommand>".
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1129

Message: Unable to modify the BootOnce object.
Detailed Description: The BootOnce object could not be modified, because the FirstBootDevice object is set to either F10, F11, or BIOS.
Recommended Response Action: Configure the FirstBootDevice object to values other than F10, F11, or BIOS and retry the set operation for the BootOnce object. For more information about possible FirstBootDevice values, run the RACADM command "racadm help idrac.serverboot.firstbootdevice".
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1130

Message: Unable to complete the operation. This feature is not supported on the currently-used platform.
Detailed Description: The requested operation could not be successfully completed because of an unsupported version of BIOS, USC, and/or iDRAC firmare.
Recommended Response Action: Verify whether or not a correct version of BIOS, Lifecycle Controller, and/or iDRAC firmware is installed. For more information on the appropriate firmware version required, refer to the RACADM Command Line Reference Guide. Also check if there is a limitation in terms of platforms such as monolithic or modular, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1131

Message: iDRAC was successfully reset.
Detailed Description: The iDRAC was reset and is successfully restarted.
Recommended Response Action: None.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1132

Message: Unable to update the firmware. The value entered for an option is invalid.
Detailed Description: The firmware could not be successfully updated, because one or all of the following values are incorrect: a. logon ID b. IP address of TFTP or FTP server c. Full path of the firmware file.
Recommended Response Action: Run the racadm command "racadm help <subcommand>" to get more details about the various options applicable for this command and the values accepted by the command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1133

Message: BIOSRTDRequested value is modified successfully.The BIOS reset to default values operation is pending a server restart.
Detailed Description: The BIOSRTDRequested attribute was modified successfully.The BIOS reset to default values operation is pending a server restart.
Recommended Response Action: To apply the BIOS default values, restart the server. After the server has restarted, the default BIOS values will be accessible from the iDRAC.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1134

Message: Unable to export the Lifecycle log data, because the export file size larger than 25MB and cannot be processed locally.
Detailed Description: Unable to export the Lifecycle log data, because the export file size larger than 25MB and cannot be processed locally.
Recommended Response Action: Export the Lifiecycle Log to a network file share. Using the RACADM command line utility, run the lclog export command with --complete option and related network file share parameters, and then retry the operation. For more information about the --complete option, run the "racadm help lclog export" command at the command line interface.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1135

Message: Unable to run the RACADM command because an internal instrumentation component has stopped functioning.
Detailed Description: The RACADM command could not be run because the internal instrumentation components are either busy or have stopped functioning.
Recommended Response Action: Wait for a minute for the internal instrumentation component to respond, and then retry the operation. If the issue persists, reset the iDRAC by pressing the System ID button for 15 seconds, wait for the iDRAC to finish restarting, and then retry the operation. If the issue continues to persist, contact your service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1136

Message: Remote unattended diagnostic execution operation initiated.
Detailed Description: The remote unattended diagnostic execution operation is initiated.
Recommended Response Action: Using the RACADM command line interface, run the "racadm jobqueue view -i <job id>" command to view the status of the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC	✔				✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔
CMC

RAC1137

Message: Remote unattended diagnostic results export operation initiated.
Detailed Description: Remote unattended diagnostic results export operation initiated.
Recommended Response Action: Using the RACADM command line interface, run the "racadm jobqueue view -i <job id>" command to view the status of the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC	✔				✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔
CMC

RAC1138

Message: Unable to export the diagnostics results because the results do not exist.
Detailed Description: Unable to export the remote diagnostics results because the remote diagnostics results have not been generated.
Recommended Response Action: Using the RACADM command line interface, run the "racadm diagnostics run" command to make sure that the diagnostics results are available, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1139

Message: The entered option is not supported by the interface.
Detailed Description: The requested file can be exported from the firmware racadm only to a remote file share.
Recommended Response Action: Create a remote file share to export the file or use remote or local racadm to export to the file system that is accessible by the racadm executable.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1140

Message: File name is not required to export the Technical Support Report (TSR) to a remote share.
Detailed Description: The file name cannot be specified when the Technical Support Report (TSR) is exported to a remote share.
Recommended Response Action: Run the command without using the -f option. For more information on exporting Technical Support Report (TSR), run the command racadm help techsupreport export.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1141

Message: The iDRAC firmware rollback operation was initiated.
Detailed Description: The iDRAC firmware rollback operation was initiated.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1142

Message: Unable to start the Remote Diagnostics operation because the Expiration Time entered (difference between Start Time and Expiration Time) is less than five minutes.
Detailed Description: The Remote diagnostic operation cannot be performed because the difference between "Start Time" and "Expiration Time" is less than 5 minutes.
Recommended Response Action: Make sure that the Expiration Time is greater than five minutes, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1143

Message: Configuration results are not applicable for the job type for Job: arg1 .
Arguments: arg1 = job ID
Detailed Description: The job identified in the message is not a configuration job, a configuration XML import or preview type job that generates configuration results.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1144

Message: The Job: arg1 is invalid or is not present in the job queue and a related Lifecycle Log entry is not found.
Arguments: arg1 = job ID
Detailed Description: No configuration results information is available for the job ID identified in the message because the job ID is invalid or is not present in the job queue and a related Lifecycle Log entry is not found.
Recommended Response Action: Check the job ID identified in the message and retry the operation with a valid job ID. To check valid job IDs in the current job queue, using RACADM, run the command "racadm jobqueue view".
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1145

Message: The entered log type is invalid.
Detailed Description: The value entered for the -t option is invalid.
Recommended Response Action: Check help text for the list of valid log types and retry the operation by entering a valid log type.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1146

Message: Unable to set the SNMPv3 username because SNMPv3 is not enabled for the specified user on iDRAC.
Detailed Description: The SNMPv3 username cannot be set because SNMPv3 is not enabled for the specified user on iDRAC.
Recommended Response Action: Enable SNMPv3 for the specified user by running the command "racadm set iDRAC.Users.<user index>.SNMPv3Enable 1", and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1147

Message: Unable to set the SNMPv3 username entered in the command because the username is not present or enabled on iDRAC.
Detailed Description: The SNMPv3 user cannot be set because the user with the entered username for the SNMPv3 group is not present or enabled on iDRAC.
Recommended Response Action: Make sure the specified username is present on iDRAC and enabled, and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1150

Message: Unable to complete the export operation.
Detailed Description: The export operation did not be complete successfully.
Recommended Response Action: Retry the export operation after five minutes.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1151

Message: The export operation is unsuccessful.
Detailed Description: The export operation did not complete successfully.
Recommended Response Action: Run the RACADM techsupreport collect command again and then retry the export operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1152

Message: The export operation completed successfully.
Detailed Description: The export operation completed successfully.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1153

Message: The time stamp is not available to display.
Detailed Description: The time stamp was not recorded for the previous techsupreport collect operation.
Recommended Response Action: Run the RACADM techsupreport collect command. After the techsupreport collect operation completes, run the RACADM getupdatetime command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1154

Message: The requested operation is initiated.
Detailed Description: The requested techsupreport collect or export operation is initiated.
Recommended Response Action: Run the RACADM jobqueue sub-command, using the job id to check the status of the requested operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1155

Message: Unable to complete the operation because Lifecycle Controller is disabled.
Detailed Description: The operation was not completed because Lifecycle Controller is disabled.
Recommended Response Action: Enable the Lifecycle Controller and retry the operation. To enable Lifecycle Controller, run the command racadm set LifeCycleController.LCAttributes.LifecycleControllerState 1.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1156

Message: Unable to display the information about the server network interfaces.
Detailed Description: The server network interface information cannot be received because the iDRAC Service Module is not installed or not runing on the server operating system (OS) or collection of the OS data is disabled.
Recommended Response Action: Run the command racadm get iDRAC.ServiceModule to check if iDRAC Service Module is installed and running on the server operation system, and the collection of the OS data is enabled.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1157

Message: Unable to find the specified FQDD.
Detailed Description: The specified FQDD is invalid.
Recommended Response Action: Verify whether or not the entered FQDD is valid. Run the command racadm gethostnetworkinterfaces for the list of valid FQDDs.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1158

Message: The requested number of log entries exceeds the limit.
Detailed Description: The requested number of Lifecycle log entries exceed the limit and cannot be displayed. The remote RACADM operation may time out before retrieving all the log entries.
Recommended Response Action: Retrieve a smaller number of log entries using remote RACADM or use firmware or local RACADM to view all the log entries. To retrieve a limited number of log entries, use the -n option. For example, to view the last 10 log entries, run the command racadm lclog view -n 10.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1159

Message: Unable to get the requested data from iDRAC.
Detailed Description: The data cannot be retrieved from iDRAC because Lifecycle Controller is disabled or a DUP update is in progress.
Recommended Response Action: Do the following: 1) Check if a DUP fw update is progress and wait until it is finished. 2) Make sure the Lifecycle Controller is Enabled. To enable Lifecycle Controller, run the command racadm set LifeCycleController.LCAttributes.LifecycleControllerState 1. 3) Retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1160

Message: Unable to set USB group objects because of insufficient privilege for user account arg1 .
Arguments: arg1 = username
Detailed Description: Unable to set USB group objects because the user account identified in the message does not have the System Control privilege, which is required for this operation.
Recommended Response Action: Contact the iDRAC system administrator and get the System Control privilege added to the account identified in the message or use account credentials that have System Control privilege and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1161

Message: Unable to initiate the techsupreport collect operation for the Tech Support Report (TSR) because the iDRAC Service Module (iSM) is not running.
Detailed Description: Unable to initiate the techsupreport collect operation because the iDRAC Service Module (iSM) is not running.
Recommended Response Action: Run the command racadm get iDRAC.ServiceModule to make sure that iDRAC Service Module is installed and running on the server operation system (OS) and also to verify that the collection of the server OS data is enabled.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1162

Message: Unable to initiate the techsupreport collect operation for the Tech Support Report (TSR) because another collect operation is in progress.
Detailed Description: The requested techsupreport collect operation cannot be initiated because another techsupreport collect operation for the Tech Support Report (TSR) is in progress.
Recommended Response Action: Wait for the current collect operation to complete before initiating another collect operation. To view the status of the techsupreport collect operation, run the command racadm jobqueue view.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1163

Message: The peak utilization value of out-of-band performance monitoring sensor arg1 is successfully reset.
Arguments: arg1 = sensor name
Detailed Description: The peak utilization value of out-of-band performance monitoring sensor identified in the message is successfully reset.
Recommended Response Action: No response action required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1164

Message: A remote diagnostics operation is currently running and not completed.
Detailed Description: A remote diagnostics operation is already under execution and another operation can be started only after the current execution is completed.
Recommended Response Action: Initiate another diagnostics operation only after the currently running operation is completed.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1165

Message: Unable to configure the port number that is entered for either http or https ports of the iDRAC Web server, because the port number is already in use.
Detailed Description: Unable to configure the port number that is entered for either http or https ports of the iDRAC Web server, because the port number is already in use.
Recommended Response Action: Enter a port number that is not already in use and retry the operation. If the issue persists, contact your service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1166

Message: Successfully initiated Configuration XML file preview operation that was invoked by arg1 .
Arguments: arg1 = user name
Detailed Description: The Configuration XML file preview operation was successfully initiated after it was invoked by the user name identfied in the message.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC	✔				✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔
CMC

RAC1168

Message: The RACADM "getconfig" command will be deprecated in a future version of iDRAC firmware.
Detailed Description: The RACADM "getconfig" command will be deprecated in a future version of iDRAC firmware.
Recommended Response Action: Run the RACADM "racadm get" command to retrieve the iDRAC configuration parameters. For more information on the get command, run the RACADM command "racadm help get".
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1169

Message: The RACADM "config" command will be deprecated in a future version of iDRAC firmware.
Detailed Description: The RACADM "config" command will be deprecated in a future version of iDRAC firmware.
Recommended Response Action: Run the RACADM "racadm set" command to configure the iDRAC configuration parameters. For more information on the set command, run the RACADM command "racadm help set".
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1170

Message: Unable to find the SSL library in the default path.
Detailed Description: Unable to find the SSL library. This can be because, the library is not installed in the default path or no SSL library is installed.
Recommended Response Action: If a SSL library is not installed, install one and retry the operation. If a SSL library is installed, create a soft-link of the installed SSL library to "libssl.so" using the linux "ln" command and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1175

Message: Unable to change the user configuration because modifying the user configuration at index 1 is not allowed.
Detailed Description: The user configuration cannot be modified, because modification is not allowed at index 1.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1176

Message: Unable to generate the Certificate Signing Request (CSR) message because all the attributes in the iDRAC.Security group are not configured.
Detailed Description: The Certificate Signing Request (CSR) message cannot be generated because all the attributes in the iDRAC.Security group are not configured.
Recommended Response Action: Make sure that all the attributes in the iDRAC.Security group are configured. To get the list of attributes, run the following command "racadm get iDRAC.Security".
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1177

Message: A USB device is attached to the iDRAC.
Detailed Description: A USB device is attached to the iDRAC and accessible from the iDRAC.
Recommended Response Action: No response action is required. To attach the USB device to the server instead of the iDRAC, remove the USB device from the front panel USB port, change the USB Management Port mode settings and then reinsert the USB device.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1178

Message: A USB device is attached to the iDRAC and a configuration XML import operation is in progress.
Detailed Description: A USB device is attached to the iDRAC and a configuration XML import operation is in progress.
Recommended Response Action: Wait until the configuration XML import operation has completed before attempting another operation. Verify the status of the configuration XML import operation by running the RACADM command "racadm jobqueue view".
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1179

Message: Unable to complete requested operation because an Type A/A USB cable is connected to the front panel USB port and the iDRAC is emulating a NIC device.
Detailed Description: Unable to complete requested operation because a Type A/A USB cable is connected to the front panel USB port and the iDRAC is emulating a NIC device.
Recommended Response Action: To change the USB Management Port mode setting, remove the Type A/A USB cable from the front panel USB port and change the port mode settings.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1180

Message: A USB device is inserted in the front panel USB Management port and is in use by the server operating system.
Detailed Description: A USB Device inserted in the front panel USB Management port and is in use by the server operating system. The device needs to not be in use in order to change the port mode settings.
Recommended Response Action: Remove and reinsert the USB device and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1181

Message: Unable to change USB Management Port mode.
Detailed Description: USB Management Port state cannot be changed because of an unknown hardware or firmware issue.
Recommended Response Action: To change the Management Port mode settings do the following: If a device is present, remove and reinsert the USB device from the front panel USB Mangement port and retry the operation. If the issue persists restart the iDRAC and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1182

Message: Unable to retrieve information for the Power group or attribute because the server is not PMBus capable.
Detailed Description: The server instrumentation can not provide any information related to power because PMBus capability is not present or the PSU(s) with PMBus capability have been removed.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1183

Message: Unable to assign IP addresses 169.254.0.3 and 169.254.0.4 to the device OSBMC USBNIC because the IP addresses entered are reserved for the iDRAC Direct feature.
Detailed Description: The IP addresses 169.254.0.3 and 169.254.0.4 cannot be assigned to the device identified in the message because the IP addresses entered are reserved for the iDRAC Direct feature.
Recommended Response Action: Enter another appropriate IP address, and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1184

Message: The getuscvresion RACADM subcommand will be deprecated in a future release.
Detailed Description: The getuscvresion RACADM subcommand will be deprecated in a future release.
Recommended Response Action: Instead of getuscversion, run the getversion -f lc subcommand.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1185

Message: Unable to configure static IPv6 address because an invalid IPv6 address or IPv6 Gateway is entered.
Detailed Description: The static IPv6 address is not configured because an invalid IPv6 address or IPv6 Gateway is entered.
Recommended Response Action: Enter a valid IPv6 address and IPv6 Gateway, and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1186

Message: 1000Mbps speed setting is Read Only and cannot be configured for the iDRAC NIC.
Detailed Description: Only possible configurations for the DRAC NIC are 10Mbps and 100 Mbps. For documentation with respect to this setting, refer to the racadm User Guide under cfgNetTuning group.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC1187

Message: Invalid Start Time Entered. Unable to start the Remote Diagnostics operation because the Start Time entered is earlier than the current iDRAC time.
Detailed Description: The remote diagnostics operation could not be initiated because the Start Time entered is invalid. It is earlier than the current iDRAC time.
Recommended Response Action: Enter a Start Time that is later than the current iDRAC time and retry the operation. Run the "racadm getractime" command to obtain the current iDRAC time.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1188

Message: Unable to configure the Upper Non-Critical value for the System Performance sensor.
Detailed Description: Unable to configure the Upper Non-Critical value for the System Perfromance sensor because the value provided is not in vaild range.
Recommended Response Action: Specify a value in the range of 0 to 100 to set the upper non-critical value.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC1189

Message: Unable to set the object value for iDRAC Service Module.
Detailed Description: The idrac.serviceModule.watchdogtmer object can not be enabled if the OS watch dog timer is already enabled.
Recommended Response Action: Disable the object using "racadm set bIOS.integratedDevices.osWatchdogTimer Disabled " Then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC802

Message: iDRAC time is set using Network Time Protocol.
Detailed Description: iDRAC time has been set through Network Time Protocol (NTP).
Recommended Response Action: No response action is required.
Category: Audit (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔*
CMC

RAC913

Message: Unable to login to RAC using the specified address
Detailed Description: The management system could not login to the iDRAC.
Recommended Response Action: Verify whether the username and password given for the iDRAC are correct.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC914

Message: Value specified is invalid: Must be 0 (Off) or 1 (On).
Detailed Description: The specified value is not within the valid range. To set the LED state to off, enter 0. To set the LED state to on, enter 1.
Recommended Response Action: Set the numeric value to 0 (Off) or 1 (On).
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC915

Message: Unable to change auto-negotiation property for the NIC.
Detailed Description: The auto-negotiation property for the iDRAC NIC can be changed only if the NIC is in dedicated mode. To change the NIC mode to dedicated, an iDRAC Enterprise license is required.
Recommended Response Action: Change the NIC mode to dedicated mode by using "racadm set idrac.nic.selection <1 | Dedicated>", and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC916

Message: Value given exceeds the maximum threshold value.
Detailed Description: The value given is greater than the maximum threshold value.
Recommended Response Action: Set values lesser than the maximum threshold value. To view the maximum threshold value, run racadm get System.Power. Cap.MaxThreshold at the command prompt.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC917

Message: The syntax of the specified command is not correct.
Detailed Description: The syntax of the specified command is incorrect.
Recommended Response Action: See the command help text. To see the help text, run "racadm help <subcommand>".
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC918

Message: Unable to get the inlet temperature data.
Detailed Description: Racadm unable to obtain the inlet temperature data. This happens if there is no data populated in the temperature tables or if the underlying instrumentation does not return valid values.
Recommended Response Action: Wait for the underlying instrumentation to populate the thermal tables. Retry the operation.
Category: System Health (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC919

Message: Copy to remote share unsuccessful. Remote share might be write protected.
Detailed Description: Racadm could not export the inlet temperature history file to the specified remote share. This is because the specified share may be write- protected.
Recommended Response Action: To export the file, change the permissions on the remote share. Else, create another share with write permissions.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC920

Message: This interface does not support the specified option.
Detailed Description: From firmware racadm, the inlet temperature history can be exported only to a remote file share.
Recommended Response Action: Create a remote file share to export the inlet temperature history. Else, use remote/local racadm to export to the file system accessible by the racadm executable.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC921

Message: The temperature history can be exported in XML or CSV format only.
Detailed Description: The file type specified (with the t parameter) is invalid. The temperature history can be exported in XML or CSV.
Recommended Response Action: Change the requested export file type to either XML or CSV. To do this, change the argument given to the t parameter. The argument given to the parameter is case-insensitive.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC922

Message: Specified path is too long.
Detailed Description: The specified path (specified with the l parameter) for the remote share is too long. This path should be less than 256 characters in length.
Recommended Response Action: Try the same command with a different remote share location, which is less than 256 characters in length.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC923

Message: The file path is too long.
Detailed Description: The specified file path (specified with the f parameter) is too long. This path should be less than 64 characters in length.
Recommended Response Action: Try the same command with a shorter file path (specified with the f parameter) which is less than 64 characters in length.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC924

Message: Inlet temperature history exported successfully.
Detailed Description: The inlet temperature history was successfully exported to the specified file.
Recommended Response Action: None.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC925

Message: Recurrence interval is not applicable for this subcategory.
Detailed Description: An alert recurrence cannot be set for the specified subcategory. The alert recurrence is applicable only to the TMPS subcategory.
Recommended Response Action: 1. Check if the alert recurrence is applicable to this subcategory. To check this run racadm eventfilters get. 2. To set the notifications for the specified subcategory, run the command without the -r option.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC926

Message: The recurrence interval needs to be an integer from 0 to 365.
Detailed Description: The value given for the recurrence interval is invalid. It has to be a value from 0 to 365.
Recommended Response Action: Change the argument of r to a value from 0 to 365 and then run the same command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC927

Message: Recurrence value modified successfully.
Detailed Description: The recurrence value was successfully modified to the specified value.
Recommended Response Action: None.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC928

Message: Unable to modify the recurrence value.
Detailed Description: Racadm unable to set the recurrence value. This occurs if the underlying instrumentation do not set the value.
Recommended Response Action: Wait for a few minutes and retry the command. If the problem persists, contact the service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)
: No alerts are applicable for this message

RAC929

Message: Invalid category or subcategory specified.
Detailed Description: The category or subcategory specified is incorrect. The recurrence interval is applicable only to the TMPS subcategory and system category.
Recommended Response Action: See the command help text, for a list of valid categories.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC930

Message: Unable to export the inlet temperature data.
Detailed Description: Racadm is currently unable to obtain the inlet temperature data. This happens if there is no data populated in the temperature tables or if the instrumentation does not return valid values.
Recommended Response Action: Wait for the instrumentation to populate the thermal tables. Retry the operation. If the problem persists, contact the service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)
: No alerts are applicable for this message

RAC936

Message: Unable to change the hot spare property for the PSU.
Detailed Description: iDRAC cannot enable or disable the hot spare property, because the system has a non-PMBus PSU.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC937

Message: Successfully initiated configuration XML file import operation that was invoked by the arg1 .
Arguments: arg1 = user name
Detailed Description: The configuration XML file import operation was successfully initiated after it was invoked by the user specified in the message.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC	✔				✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔
CMC

RAC938

Message: Successfully initiated configuration XML file export operation invoked by the arg1 .
Arguments: arg1 = user name
Detailed Description: The configuration XML file export operation was successfully initiated after it was invoked by the user specified in the message.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC	✔				✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC	✔
CMC

RAC939

Message: Unable to start the system configuration profile export or import operation.
Detailed Description: The request to perform a system profile export or import opeartion cannot be started because a firmware update operation is already in progress.
Recommended Response Action: Wait until the update operation is completed or cancel the update operation, and retry.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC940

Message: Unable to start the system configuration profile export or import operation.
Detailed Description: If an existing system profile import or export job is running, then a system configuration profile backup or restore opeartion cannot be started.
Recommended Response Action: Wait until the existing system profile export or import job is completed or cancel the job before retrying the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC941

Message: Successfully initiated the export operation. This operation may take several minutes to complete.
Detailed Description: A system configuration profile export operation may take several minutes to complete depending on the system configuration.
Recommended Response Action: Monitor the job status using "racadm jobqueue view -i <Job ID>".
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC942

Message: Successfully initiated the import operation. This operation may take several minutes to complete and may cause multiple system restarts while device firmware and configuration are applied.
Detailed Description: The system configuration profile import operation is initiated. No other operations can be performed on the system while the system configuration server profile is being imported from the system configuration profile.
Recommended Response Action: Monitor the job status using "racadm jobqueue view -i <Job ID>".
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC943

Message: Warning: Collect System Inventory On Restart (CSIOR) feature is disabled.
Detailed Description: The Collect System Inventory On Restart (CSIOR) feature is currently disabled. If the system inventory is not up-to-date, the system configuration profile that is being copied will not have the latest inventory information.
Recommended Response Action: To get latest inventory information, cancel the current export job, run "racadm set LifecycleController.LCAttributes.CollectSystemInventoryOnRestart 1" to enable CSIOR, and re-initiate the export operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC944

Message: Unable to create the configuration job.
Detailed Description: A configuration job cannot be created if Lifecycle Controller is disabled.
Recommended Response Action: Run "racadm set LifecycleController.LCAttributes.LifecycleControllerState 1" to enable Lifecycle Controller, and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC945

Message: Invalid object value specified.
Detailed Description: The dedicated NIC or shared NIC scan time value is not between 5 and 255 seconds.
Recommended Response Action: Make sure to set the scan time value between 5 and 255 seconds, and retry the operation. For more information, see RACADM help.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC946

Message: Unable to set the NIC to Auto Dedicated NIC mode.
Detailed Description: The "Auto Dedicated NIC" mode cannot be set for a NIC if the NIC selection mode is set to "Dedicated NIC".
Recommended Response Action: To set the NIC to Auto Dedicated NIC mode, set NIC selection mode to "Shared NIC", and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC947

Message: Invalid object value specified.
Detailed Description: The value used for the object set operation is invalid.
Recommended Response Action: Make sure to specify the value depending on the type of object. For more information, see RACADM help.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC948

Message: Unable to send the notification for the specified event to the configured destination.
Detailed Description: A test event notification for the specified message ID was not sent to the configured destination.
Recommended Response Action: Make sure to the use a valid message ID, set the required notification filter, and retry the operation. If the issue persists, contact your service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC949

Message: Successfully added a work note to the Lifecycle Log.
Detailed Description: The specified work note was added to the Lifecycle Log.
Recommended Response Action: View the work notes using the racadm lclog view c worknotes command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC950

Message: Unable to add the work note to the Lifecycle Log.
Detailed Description: The work note cannot be added to the Lifecycle Log if iDRAC is archiving the older records in the Lifecycle Log.
Recommended Response Action: Wait for several minutes while iDRAC archives the older records, and then retry the operation. If the issue persists, contact your service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC951

Message: The number of characters entered for the work note exceeds the supported limit.
Detailed Description: Up to 256 characters are allowed for a work note.
Recommended Response Action: Do not exceed 256 characters in the work note, and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC952

Message: There is no free space to add new work notes to the Lifecycle Log.
Detailed Description: The allocated size for the Lifecycle Log entries has reached its maximum limit, and no further work notes can be added to the Lifecycle Log.
Recommended Response Action: Contact your service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC953

Message: Successfully added the comment.
Detailed Description: The comment was added to the specified entry in the Lifecycle Log.
Recommended Response Action: View the added comment using the racadm lclog view q <seq. no> -n 1 command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC954

Message: The number of characters entered for the comment exceeds the supported limit.
Detailed Description: Up to 128 characters are allowed for a comment.
Recommended Response Action: Do not exceed 128 characters for the comment, and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC955

Message: Unable to retrieve the information related to the specified record in the Lifecycle Log.
Detailed Description: The specified record does not exist in the Lifecycle Log.
Recommended Response Action: Run the racadm lclog view -i command to get the sequence number of the records logged in the Lifeycle Log, and retry the command with a valid sequence number.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC956

Message: There is no free space to add new comments to the Lifecycle Log.
Detailed Description: The allocated size for the Lifecycle Log entries has reached its maximum limit, and no further comments can be added to the Lifecycle Log.
Recommended Response Action: Contact your service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC957

Message: An import or export operation is currently in progress.
Detailed Description: Another import or export operation cannot be started until the current operation is complete.
Recommended Response Action: Wait until the current import or export operation is complete before starting another operation. Use the racadm jobqueue view command to check the status of the current import or export operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC958

Message: Unable to start the import or export operation.
Detailed Description: An import or export operation cannot be started until the current running job is complete.
Recommended Response Action: Wait for the current running job to complete before starting another operation. Current job running can be update or backup or file export or similar job. Use the racadm jobqueue view command to check the status of the current update operation jobs.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC959

Message: Invalid file used for configuration XML file import operation.
Detailed Description: The content of the configuration XML file used for import is invalid because of incorrect modifications or content.
Recommended Response Action: Correct the modifications to the configuration XML file to be imported or specify the correct file, and retry the operation. Check the Lifecycle Log for more details.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC960

Message: Unable to find the specified configuration XML file for import.
Detailed Description: The configuration XML file specified for import cannot be located in the specified repository.
Recommended Response Action: Make sure the specified file name is correct and is located in the specified repository, and retry the operation. For more information about the syntax, run "racadm help set" to view RACADM help.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC961

Message: A pending or committed system configuration change exists.
Detailed Description: Another import operation cannot be started if an import operation that was performed earlier has some pending or commited configuration changes.
Recommended Response Action: Wait until the configuration changes are applied before starting another import operation. Use the racadm jobqueue view command to check the status of the current import operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC962

Message: Unable to continue with the operation because Lifecycle Controller is in recovery state,
Detailed Description: Lifecycle Controller must be enabled to run the operation.
Recommended Response Action: Enable the Lifecycle controller using the racadm set LifeCycleController.LCAttributes.LifecycleControllerState 1 command, and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC963

Message: Unable to retrieve the status of Lifecycle Controller.
Detailed Description: iDRAC is unable to read Lifecycle Controller status. Lifecycle Controller must be enabled to run the operation.
Recommended Response Action: Run the racadm get LifeCycleController.LCAttributes.LifecycleControllerState command to get the status of the Lifecycle Controller. If the issue persists, contact your service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC964

Message: Unable to perform the operation.
Detailed Description: The operation cannot be performed because of an internal error.
Recommended Response Action: Wait for some time before retrying the operation. If the issue persists, contact your service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC965

Message: The -l option must be specified if -u and -p are used.
Detailed Description: Any operation involving remote share (CIFS) cannot continue if the location (-l) is not specified. The u and p options represent the user name and password for the remote share, and -l represents the location of the remote share.
Recommended Response Action: Make sure to specify the location (-l) of the remote share along with the user name and password, and retry the operation. To view the list of options that can used for the required subcommand, use the racadm help <subcommand> command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC966

Message: Unable to continue with the opearion because the user name or password is not specified.
Detailed Description: Any operation involving remote share (CIFS) cannot continue if user name, password, or both are not specified. The u and p options represent the user name and password for the remote share.
Recommended Response Action: Make sure to specify both user name and password for the remote share, and retry the operation. To view the list of options that can used for the required subcommand, use the racadm help <subcommand> command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC967

Message: Exporting the configuration XML file to a local share is not supported when using Firmware RACADM.
Detailed Description: The configuration XML file can only be exported to a remote share while using Firmware RACADM.
Recommended Response Action: When using Firmware RACADM, make sure to export the configuration XML file to a remote share only.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC968

Message: Importing the configuration XML file from a local share is not supported when using Firmware RACADM.
Detailed Description: The configuration XML file cannot be imported from a client location when using Firmware RACADM.
Recommended Response Action: When using Firmware RACADM, make sure to import the configuration XML file from a remote share only.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC969

Message: Incorrect value specified for the shutdown option.
Detailed Description: The import operation cannot continue if the value specified for the shutdown option (-b) is incorrect. The supported values are "Graceful" and "Forced".
Recommended Response Action: Make sure to specify either "Graceful" or "Forced" for the shutdown (-b) option.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC970

Message: Incorrect value specified for the end power state option.
Detailed Description: The import operation cannot continue if the value specified for the end power state of the system option (-s) is incorrect. The supported values are "On" and "Off".
Recommended Response Action: Make sure to specify either "On" or "Off" for the end power state (-s) option.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC971

Message: Incorrect file type specified.
Detailed Description: The import or export operation cannot continue if the value specified for the file type is incorrect. The correct value for the file type is "xml" or "ini".
Recommended Response Action: Make sure to specify either "xml" or "ini" for the file type (-t) option. If no file type is specified, "ini" is used as default.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC972

Message: Insufficient privileges to run the configuration XML file import or export operations.
Detailed Description: Configuration XML import and export operations require the specified username to have administrator role privileges.
Recommended Response Action: Run the same command with a username that has an administrator role privileges.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC973

Message: The imported configuration XML file matches the current system configuration.
Detailed Description: The configuration XML file which was specified for import, had the same configuration as the current system configuration.
Recommended Response Action: Make any desired system configuration changes to the configuration XML file and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC974

Message: Invalid wait time specified.
Detailed Description: The value specified for the wait time (w) option is invalid. The valid range is 300 to 3600 seconds.
Recommended Response Action: Make sure to specify a valid wait time (-w) option and retry the command. The range of supported values are 300 to 3600 seconds.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC975

Message: Invalid share type specified.
Detailed Description: The share type specified using the l parameter is invalid. Only CIFS or NFS share types are supported for this operation.
Recommended Response Action: See the subcommand help text for supported share types.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC976

Message: Export configuration XML file operation initiated.
Detailed Description: The configuration XML file export operation was initiated.
Recommended Response Action: Use the racadm jobqueue view i <Job ID> command to view the status of the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC977

Message: Import configuration XML file operation initiated.
Detailed Description: The configuration XML file import operation was initiated.
Recommended Response Action: Use the racadm jobqueue view i <Job ID> command to view the status of the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC978

Message: Unsupported Lifecycle Controller firmware version detected.
Detailed Description: The Lifecycle Controller firmware version on the target system does not support the configuration XML file import or export operations.
Recommended Response Action: Update to the latest Lifecycle Controller firmware and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC979

Message: Successfully uploaded the custom signing certificate to iDRAC.
Detailed Description: The custom signing certificate was extracted from the Public Key Cryptography Standards version 12 (PKCS12) file and applied to the system configuration.
Recommended Response Action: No response action required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC981

Message: The type of certificate specified does not require a passphrase.
Detailed Description: A passphrase is required only for passphrase protected certificate, which is specified using the value of 3 for the -t option.
Recommended Response Action: If the file being uploaded is passphrase protected, specify the file type as 3 using the -t option. If the file is not passphrase protected, retry the command, without specifying the -p option.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC982

Message: Invalid Public Key Cryptography Standards version 12 (PKCS12) file detected.
Detailed Description: The PKCS12 file provided is invalid, because it may not be in the correct format.
Recommended Response Action: For more details, contact the Certificate Authority.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC983

Message: Invalid passphrase provided for the Public Key Cryptography Standards version 12 (PKCS12) file.
Detailed Description: The Public Key Cryptography Standards version 12 (PKCS12) file is passphrase protected, and the passphrase provided is invalid.
Recommended Response Action: Specify the correct passphrase for the file using -p option.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC984

Message: Unable to upload the Public Key Cryptography Standards version 12 (PKCS12) file.
Detailed Description: iDRAC is unable to extract the custom signing certificate and the private key from the Public Key Cryptography Standards version 12 (PKCS12) file.
Recommended Response Action: Check if the specified file and passphrase are valid, and retry the operation. If the issue persists, contact your service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC985

Message: Unable to configure the cfgServerBootOnce object.
Detailed Description: The object "cfgServerBootOnce" cannot be configured if the object "cfgServerFirstBootDevice" is set to F10, F11, or BIOS value.
Recommended Response Action: Change the value of the object "cfgServerFirstBootDevice" using the RACADM command "racadm config -g cfgServerInfo -o cfgServerFirstBootDevice<value other than F10, F11, and BIOS>", and retry configuring the object "cfgServerBootOnce".
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC986

Message: The "vmkey" sub-command is deprecated.
Detailed Description: The "vmkey" sub-command is deprecated, and the functionality is available using "vflashsd" sub-command.
Recommended Response Action: Use "vflashsd" sub-command instead of "vmkey". For more information about the sub-command, use "racadm help vflashsd" command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC987

Message: Firmware update job for arg1 is initiated.
Arguments: arg1 = file name
Detailed Description: After initiating the firmware update job, the time taken to complete it depends on size of the update file.
Recommended Response Action: This firmware update job may take several minutes to complete depending on the component or firmware being updated. To view the progress of the job, use the "racadm jobqueue view" command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC988

Message: Unable to initiate the arg1 firmware update.
Arguments: arg1 = file name
Detailed Description: A new firmware update job cannot be initiated while an existing firmware update job is still in one of these states: "New", "Downloading", or "Running".
Recommended Response Action: Wait until the existing firmware update jobs are completed or scheduled before retrying the operation. To monitor the status of the existing jobs, use the "racadm jobqueue view" command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC989

Message: Unable to apply the arg1 firmware update.
Arguments: arg1 = file name
Detailed Description: Only Windows-based Update Package (.exe extension), iDRAC Firmware (.d7 extension), Personality Module Firmware (.pm extension), Lifecycle Controller firmware repair package (.usc) are supported for the firmware update operation.
Recommended Response Action: The file used for the operation is invalid. For the list of supported files, use "racadm help update". For the correct version of the file specific to the system, contact the service provider.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC990

Message: Unable to apply the arg1 update.
Arguments: arg1 = file name
Detailed Description: If Lifecycle Controller is disabled, the firmware update operation cannot continue.
Recommended Response Action: Enable Lifecycle Controller using the "racadm set lifecyclecontroller.lcattributes.lifecyclecontrollerstate 1" command, and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC991

Message: Unable to run the "jobqueue" command.
Detailed Description: The "jobqueue" command cannot be run, because the existing update jobs are transitioning to one of these states: "New", "Downloading", or "Running".
Recommended Response Action: Wait until the existing update jobs are completed before retrying the operation. To monitor the status of the existing jobs, use the "racadm jobqueue view" command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC992

Message: Invalid job: arg1 .
Arguments: arg1 = job ID
Detailed Description: The job ID specified in the message is invalid or was already deleted.
Recommended Response Action: To monitor the current set of the jobs, use the "racadm jobqueue view" command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC993

Message: The job: arg1 was deleted.
Arguments: arg1 = job ID
Detailed Description: The job ID specified in the message was deleted.
Recommended Response Action: No response action is required.
Category: Configuration (RAC = RAC Event)
Severity: Severity 3 (Informational)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC994

Message: Unable to run the "jobqueue delete --all" command.
Detailed Description: The jobs cannot be deleted if they are in one of these states: "Scheduled" or "Running". However, all jobs in one of these states: "Completed" or "Failed" will be deleted.
Recommended Response Action: To monitor the job status, use the "racadm jobqueue view -i <job ID>", and delete the jobs one at a time using the "racadm jobqueue delete -i <job ID>" command.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC995

Message: Unable to retrieve the hardware inventory.
Detailed Description: The hardware inventory cannot be retrieved because another hardware inventory operation may already be in progress or due to an internal error whether or not Collect System Inventory On Restart (CSIOR) is enabled or disabled.
Recommended Response Action: Another hardware inventory operation may already be in progress and must complete before retrying the operation. If no other hardware inventory operation was in progress, make sure to enable Collect System Inventory On Restart (CSIOR) feature, reboot the system, and retry the operation. If CSIOR is already enabled and no other hardware inventory operation was in progress, reboot the iDRAC using "racadm racreset" command and then retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC996

Message: Unable to set the object value because the DNS RAC Name object is not configured.
Detailed Description: Unable to set the specified object value because the object DNS RAC Name is not configured.
Recommended Response Action: Configure DNS Rac Name using "racadm set iDRAC.NIC.DNSRacName <Name>" command, and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC997

Message: The object DNSDomainFromDHCP cannot be enabled.
Detailed Description: The DHCP for Domian Name cannot be enabled if IPv4 and IPv4 DHCP or IPv6 and IPv6 AutoConfig is disabled.
Recommended Response Action: Make sure that IPv4 and IPv4 DHCP are enabled, or IPv6 and IPv6 AutoConfig are enabled.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC998

Message: IPv6 cannot be enabled.
Detailed Description: IPv6 cannot be enabled if iDRAC NIC is disabled.
Recommended Response Action: Enable iDRAC NIC using "racadm set iDRAC.NIC.Enable < 1 | Enabled >" command and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

RAC999

Message: The object DNSFromDHCP6 cannot be enabled.
Detailed Description: DNSFromDHCP6 cannot be enabled if iDRAC IPv6 AutoConfig is disabled.
Recommended Response Action: Enable IPv6 AutoConfig using "racadm set iDRAC.IPv6.AutoConfig < 1 | Enabled >" command, and retry the operation.
Category: Configuration (RAC = RAC Event)
Severity: Severity 2 (Warning)

	Filter Visibility	IPMI Alert	SNMP Alert	Email Alert	Remote System Log	WS Eventing
iDRAC					✔
CMC

	LC Log	LCD	OS Log	Power Off	Power Cycle	Reset	Chassis Event Proxy
iDRAC
CMC

Welcome

Welcome to Dell

Event and Error Message Reference Guide for 13th Generation Dell PowerEdge ServersVersion 1.2

RAC Event Messages

RAC001

RAC002

RAC003

RAC004

RAC005

RAC006

RAC007

RAC008

RAC009

RAC010

RAC0100

RAC0101

RAC0102

RAC0103

RAC0104

RAC0105

RAC0106

RAC0107

RAC0108

RAC011

RAC0113

RAC0115

RAC0116

RAC0117

RAC0118

RAC012

RAC0120

RAC0121

RAC0124

RAC0126

RAC0127

RAC0128

RAC0129

RAC013

RAC0130

RAC0131

RAC0132

RAC0133

RAC0134

RAC0135

RAC0136

RAC0137

RAC0138

RAC014

RAC0140

RAC0141

RAC0142

RAC0146

RAC0147

RAC0148

RAC0149

RAC015

RAC0150

RAC0151

RAC0152

RAC0153

RAC0154

RAC0155

RAC0156

RAC0158

RAC0159

RAC016

RAC0160

RAC0169

RAC017

RAC0171

RAC018

RAC0180

RAC019

RAC020

RAC0206

RAC0207

RAC0208

RAC0209

RAC021

RAC0211