- Notes, Cautions, and Warnings
- Introduction
- AMP Event Messages
- ASR Event Messages
- BAR Event Messages
- BAT Event Messages
- BIOS Event Messages
- BOOT Event Messages
- CBL Event Messages
- CMC Event Messages
- CPU Event Messages
- CPUA Event Messages
- CTL Event Messages
- DH Event Messages
- DIAG Event Messages
- DIS Event Messages
- DKM Event Messages
- ECM Event Messages
- ENC Event Messages
- EPP Event Messages
- FAN Event Messages
- FC Event Messages
- FCD Event Messages
- FLDC Event Messages
- FSD Event Messages
- HWC Event Messages
- IOID Event Messages
- IOV Event Messages
- IPA Event Messages
- ISM Event Messages
- JCP Event Messages
- LC Event Messages
- LIC Event Messages
- LNK Event Messages
- LOG Event Messages
- MEM Event Messages
- NIC Event Messages
- OSD Event Messages
- OSE Event Messages
- PCI Event Messages
- PDR Event Messages
- PFM Event Messages
- POW Event Messages
- PR Event Messages
- PST Event Messages
- PSU Event Messages
- PSUA Event Messages
- PWR Event Messages
- RAC Event Messages
- RDU Event Messages
- RED Event Messages
- RFL Event Messages
- RFLA Event Messages
- RFM Event Messages
- RRDU Event Messages
- RSI Event Messages
- SEC Event Messages
- SEL Event Messages
- SSD Event Messages
- STOR Event Messages
- SUP Event Messages
- SWC Event Messages
- SWU Event Messages
- SYS Event Messages
- TMP Event Messages
- TMPS Event Messages
- TST Event Messages
- UEFI Event Messages
- USR Event Messages
- VDR Event Messages
- VF Event Messages
- VFL Event Messages
- VFLA Event Messages
- VLT Event Messages
- VME Event Messages
- VRM Event Messages
Event and Error Message Reference Guide for 13th Generation Dell PowerEdge ServersVersion 1.2
SWC Event Messages
SW0725
- Message
- iDRAC7 communication failure.
- Detailed Description
- iDRAC7 is busy and does not respond to iDRAC7 configuratorIPMI requests.
- Recommended Response Action
- Try AC power cycling the server or upgrade the iDRAC firmware.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
SWC0001
- Message
- Unable to save the network settings.
- Detailed Description
- The network cable may not be connected or an internal error occurred. For more information about the failure, see Lifecycle Log.
- Recommended Response Action
- Verify the network cable is connected and retry the operation. If the problem persists: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0002
- Message
- Unable to set Part Replacement policies.
- Detailed Description
- The Part Replacement policy configuration operation encountered an unexpected error while communicating with iDRAC.
- Recommended Response Action
- Retry the operation. If the problem persists: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0003
- Message
- Unable to display the Lifecycle log.
- Detailed Description
- An unrecoverable error occurred while communicating with iDRAC.
- Recommended Response Action
- Retry the operation. If the problem persists: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0004
- Message
- Unable to add a work note to the Lifecycle Log.
- Detailed Description
- The operation to add a work note to the Lifecycle Log encountered an unexpected error while communicating with iDRAC.
- Recommended Response Action
- Retry the operation. If the problem persists: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0005
- Message
- Unable to display the current hardware inventory.
- Detailed Description
- The view current hardware inventory operation encountered an unexpected error while communicating with iDRAC.
- Recommended Response Action
- Retry the operation. If the problem persists: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0006
- Message
- Unable to display the As Shipped hardware inventory.
- Detailed Description
- The view As Shipped hardware inventory operation encountered an unexpected error while communicating with iDRAC.
- Recommended Response Action
- Retry the operation. If the problem persists: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0007
- Message
- Unable to write the current hardware inventory to the specified destination.
- Detailed Description
- The export current hardware inventory operation did not complete because the destination: 1) does not have the specified folder, 2) does not have enough free space, or 3) is read-only.
- Recommended Response Action
- Retry the operation. If the problem persists, verify the following and retry the operation: 1) Destination has the specified folder. 2) Destination has enough free space. 3) Destination is not write-protected.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0008
- Message
- Unable to write the As Shipped hardware inventory to the specified destination.
- Detailed Description
- The export As Shipped hardware inventory operation did not complete because the destination: 1) does not have the specified folder, 2) does not have enough free space, or 3) is read-only.
- Recommended Response Action
- Retry the operation. If the problem persists, verify the following and retry the operation: 1) Destination has the specified folder. 2) Destination has enough free space. 3) Destination is not write-protected.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0012
- Message
- Unable to retrieve the front panel security settings.
- Detailed Description
- The operation to retrieve the front panel security settings encountered an unexpected error while communicating with iDRAC.
- Recommended Response Action
- Retry the operation. If the problem persists: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0013
- Message
- Unable to save the front panel security settings.
- Detailed Description
- The oepration to save the front panel security settings encountered an unexpected error while communicating with iDRAC.
- Recommended Response Action
- Retry the operation. If the problem persists: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0014
- Message
- Unable to set new date and time.
- Detailed Description
- Unable to apply the changes to the date and time settings because an internal error occurred.
- Recommended Response Action
- Exit the Date and Time wizard and retry the operation. If the problem persists, exit Lifecycle Controller and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0015
- Message
- Unable to retrieve the list of supported operating systems.
- Detailed Description
- The operating system driver pack is missing or not accessible.
- Recommended Response Action
- Update the system with the latest Lifecycle Controller OS Driver Pack. Obtain the OS Driver Pack from the service provider.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0016
- Message
- Unable to initialize OS Deployment wizard.
- Detailed Description
- The operating system driver pack is missing or not accessible.
- Recommended Response Action
- Exit the OS Deployment wizard and retry the operation. If the problem persists, exit Lifecycle Controller and retry the oepration.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0017
- Message
- Unable to retrieve the drivers for the selected operating system.
- Detailed Description
- An unrecoverable error occurred while retireving the drivers.
- Recommended Response Action
- Exit the OS Deployment wizard and retry the operation. If the problem persists, exit Lifecycle Controller and perform an AC power cycle.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0018
- Message
- Unable to apply the boot mode settings for BIOS.
- Detailed Description
- The BIOS boot mode settings could not be applied due to an internal error.
- Recommended Response Action
- Exit the OS Deployment wizard and retry the operation. If the problem persists, exit the Lifecycle Controller and perform an AC power cycle.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0019
- Message
- The Test Network Connection operation completed with errors.
- Detailed Description
- The Test Network Connection ping test timed-out. The network cable is disconnected or the network is not configured correctly.
- Recommended Response Action
- Check the network cable connection and network configuration settings, then retry the operation. If the problem persists, reconfigure the network settings and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0024
- Message
- The Test Network Connection ping test timed-out.
- Detailed Description
- The Test Network Connection ping test timed-out. The network cable is disconnected or the network is not configured correctly.
- Recommended Response Action
- Check the network cable connection and network configuration settings, then retry the operation. If the problem persists, reconfigure the network settings and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0025
- Message
- The operation completed successfully, however the system is unable to automatically shut down.
- Detailed Description
- The operation completed successfully, however the system is unable to automatically shut down.
- Recommended Response Action
- Manually shut down the system. For more information about the failure, see the Lifecycle Log.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0026
- Message
- Unable to retrieve status of backup Server Profile operation.
- Detailed Description
- Status of backup Server Profile operation could not be retrieved because an unrecoverable error occurred while communicating with iDRAC.
- Recommended Response Action
- Reset iDRAC and retry the operation. To reset the iDRAC, hold the System ID button down for 15 seconds or longer and wait for 90 seconds for the iDRAC to restart. For more information on the error, see the Lifecycle Log.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0027
- Message
- Successfully backed up a Server Profile by using the Lifecycle Controller GUI.
- Detailed Description
- The backup Server Profile operation successfully completed.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC0028
- Message
- The backup Server Profile operation did not successfully complete.
- Detailed Description
- iDRAC is unable to complete the backup Server Profile operation because an unrecoverable error occurred.
- Recommended Response Action
- Reset iDRAC and retry the operation. To reset the iDRAC, hold the System ID button down for 15 seconds or longer and wait for 90 seconds for the iDRAC to restart. For more information on the error, see the Lifecycle Log.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0029
- Message
- Unable to retrieve status of backup Server Profile operation.
- Detailed Description
- Status of backup Server Profile operation could not be retrieved because an unrecoverable error occurred while communicating with iDRAC.
- Recommended Response Action
- Reset iDRAC and retry the operation. To reset the iDRAC, hold the System ID button down for 15 seconds or longer and wait for 90 seconds for the iDRAC to restart. For more information on the error, see the Lifecycle Log.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0030
- Message
- Unable to complete the backup Server Profile backup operation.
- Detailed Description
- iDRAC is unable to complete the backup Server Profile operation.
- Recommended Response Action
- Reset iDRAC and retry the operation. To reset the iDRAC, hold the System ID button down for 15 seconds or longer and wait for 90 seconds for the iDRAC to restart. For more information on the error, see the Lifecycle Log.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0031
- Message
- Unable to initiate the backup Server Profile backup operation.
- Detailed Description
- iDRAC is unable to initiate the backup Server Profile operation because an unrecoverable error occurred.
- Recommended Response Action
- Reset iDRAC and retry the operation. To reset the iDRAC, hold the System ID button down for 15 seconds or longer and wait for 90 seconds for the iDRAC to restart. For more information on the error, see the Lifecycle Log.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0032
- Message
- Successfully exported the Server Configuration Profile image file to the USB drive.
- Detailed Description
- Exporting the Server Configruation Profile image file to the USB drive was successful.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC0033
- Message
- Successfully exported the Server Configuration Profile image file to network share.
- Detailed Description
- Exporting the Server Configuration Profile image file to the network share was successful.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC0034
- Message
- Unable to export the file to the network share.
- Detailed Description
- Lifecycle Controller is unable to export the file to the network share because it has insufficient free space.
- Recommended Response Action
- Make sure that the network share has sufficient free space then retry the operation. If the problem persists, check network settings and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0035
- Message
- Unable to initialize backup Server Profile operation.
- Detailed Description
- The backup operation did not initialize because the system does not have a service tag.
- Recommended Response Action
- Assign a service tag to the system and retry the operation. To assign the service tag, contact your service provider.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0036
- Message
- Unable to launch hardware diagnostics.
- Detailed Description
- Unable to launch hardware diagnostics because the Enterprise UEFI Diagnostics application is corrupt or iDRAC is not responding.
- Recommended Response Action
- Retry the operation. If the problem persists, update the Enterprise UEFI Diagnostics using one of the following methods: 1) Use the Firmware Update feature in Lifecycle Controller. 2) Use the Server Update Utility. 3) Run the Update Package from the operating system. If the problem continues to persist, reset the iDRAC. For more information, contact your service provider.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0037
- Message
- Unable to export the file to the network share.
- Detailed Description
- Lifecycle Controller is unable to export the file to the network share because the destination folder is not present or inaccessible.
- Recommended Response Action
- Make sure that the destination folder is present and accessible, then retry the operation. If the problem persists, check network settings and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0038
- Message
- Unable to export the file to the network share.
- Detailed Description
- Lifecycle Controller is unable to export the file to the network share because the destination folder is read-only or inaccessible.
- Recommended Response Action
- Remove the write protection on the destination folder and verify the folder is accessible, then rety the operation. If the problem persists, check network settings and retry.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0039
- Message
- Unable to find the backup Server Configuration Profile image.
- Detailed Description
- The backup Server Configuration Profile image partition is not present in the vFlash SD card.
- Recommended Response Action
- A backup Server Configuration Profile is required to import or export a Server Profile. Perform the backup operation and retry import or export operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0040
- Message
- Unable to complete the Import operation.
- Detailed Description
- The location of the backup Server Configuration Profile image file provided is incorrect.
- Recommended Response Action
- Enter the correct location of the backup Server Configuration Profile image file and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0041
- Message
- Unable to copy the backup Server Configuration Profile.
- Detailed Description
- The specified source file location is incorrect.
- Recommended Response Action
- Make sure that the specified source file location is correct and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0042
- Message
- Unable to retrieve the status of the Import Server Profile operation.
- Detailed Description
- Lifecycle Controller is unable to retrieve the status of the Import Server Profile operation.
- Recommended Response Action
- Exit the Import Server Profile wizard and retry the operation. If the problem persists, do the following: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds.3) Reconnect the power cord, turn on the system, and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0043
- Message
- Import Server Profile operation completed with errors.
- Detailed Description
- The Import Server Profile operation has completed with errors. For more information, see the Lifecycle Log.
- Recommended Response Action
- Exit the Import Server Profile wizard and retry the operation. If the problem persists, do the following: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0044
- Message
- Unable to retrieve the status of the Import Server Profile operation.
- Detailed Description
- Lifecycle Controller is unable to retrieve the status of the Import Server Profile operation. For more information, see the Lifecycle Log.
- Recommended Response Action
- Retry the operation. If the problem persists, do the following: 1) Turn off the system and disconnect the power cord. 2) Wait five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0045
- Message
- Unable to complete the Import operation.
- Detailed Description
- The Import operation did not successfully complete. For more information, see the Lifecycle Log.
- Recommended Response Action
- Exit the Import Server Profile wizard and retry the operation. If the problem persists, do the following: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0046
- Message
- Unable to initiate Import operation.
- Detailed Description
- Unable to initiate Import operation since another Import operation is already in progress.
- Recommended Response Action
- Wait until current Import operation is complete before initiating a new Import operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0048
- Message
- Unable to validate the backup server configuration Profile image file for this system.
- Detailed Description
- The backup server profile operation did not complete because: 1) The backup server configuration profile image file present on the vFlash SD card is invalid for this system. 2) The passphrase entered does not match the passphrase used to secure the backup server configuration profile image file.
- Recommended Response Action
- Do one of the following and retry the operation: 1) Reinsert the vFlash SD card with correct backup image file. 2) Enter the passphrase that was used to secure the backup server configuration profile image file.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0049
- Message
- Unable to continue the Import operation.
- Detailed Description
- The Import operation cannot continue because backup image file is not present on the vFlash SD card, the image is invalid, or the entered passphrase is incorrect.
- Recommended Response Action
- Make sure that the backup image file is present on the vFlash SD card, the image is valid, and the entered passphrase is correct.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0050
- Message
- Unable to initiate Import operation.
- Detailed Description
- Unable to initiate Import operation since iDRAC is not responding.
- Recommended Response Action
- Retry the Import operation using a valid backup image file and the correct passphrase. If the problem persists, do the following: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0051
- Message
- Unable to retrieve iDRAC license information.
- Detailed Description
- Unable to retreive license information due to an iDRAC communication error.
- Recommended Response Action
- Exit Lifecycle Controller and retry the operation. If the problem persists, do the following: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0052
- Message
- Unable to continue with OS Deployment operation.
- Detailed Description
- An error occurred while retrieving the operating system drivers.
- Recommended Response Action
- Exit the OS Deployment wizard and update the system with the latest operating system driver packs available from the service provider and retry the operation. For more information, see the Lifecycle Controller users guide.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0053
- Message
- File extension is not supported or the Update Package is invalid.
- Detailed Description
- The file extension of the Update Package is not supported or the Update Package is invalid.
- Recommended Response Action
- Use a valid Windows-based Update Package with an .exe extension.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0054
- Message
- Unable to save settings.
- Detailed Description
- There was an internal error while saving the settings.
- Recommended Response Action
- Retry the operation. If the problem persists, reboot the system or update the Lifecycle Controller firmware to the latest version and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0055
- Message
- Unable to load the View Current Version page.
- Detailed Description
- Unable to load the View Current Version page due to an internal error.
- Recommended Response Action
- Retry the opearation. If problem persists, update the iDRAC firmware to the latest version and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0056
- Message
- Unable to export the file to the USB drive.
- Detailed Description
- Unable to export the file to the USB drive because it does not have the specified folder, does not have enough free space, or is read-only.
- Recommended Response Action
- Make sure that the USB drive contains the folder specified, has enough free space, or is not read-only. If the problem persists, reboot the system and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0057
- Message
- Unable to export the file to the network share.
- Detailed Description
- Unable to copy the file to the network share because it does not have the specified folder, the specified folder name has space between the characters, does not have enough free space, or is read-only.
- Recommended Response Action
- Make sure that the network share has the specified folder, the specified folder name has no space between the characters, has enough free space, or is not read-only. If the problem persists, perform an AC power cycle and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0059
- Message
- Unable to complete the operation.
- Detailed Description
- vFlash partitons are being used by other applications such as Lifecycle Controller-Remote Services or RACADM.
- Recommended Response Action
- Wait until the current operations are complete and retry the operation. For information, see the FAQs section of the Lifecycle Controller-Remote Services or RACADM User Guide.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0062
- Message
- Unable to export Lifecycle Log.
- Detailed Description
- The destination folder is not present, the destination is full or write-protected.
- Recommended Response Action
- Verify the following and retry the operation: 1) Destination folder is present. 2) Destination has enough free space. 3) Destination is not write-protected. If the problem persists, perform an AC power cycle and retry.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0063
- Message
- Unable to authenticate the login credentials and share name.
- Detailed Description
- The share name and login credentials provided are incorrect.
- Recommended Response Action
- Enter the correct share name and login credentials, and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0065
- Message
- Unable to retrieve the drivers for the selected operating system.
- Detailed Description
- Lifecycle Controller is unable to copy the OS drivers from the OS driver pack.
- Recommended Response Action
- Exit the OS Deployment wizard and retry the operation. If the issue persists, do one of the following:1) Update the system with the latest operating system driver packs using the Firmware Update feature and retry the operation. 2) Reboot the system, press the <F10> key to re-enter Lifecycle Controller, and retry the operation..
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0066
- Message
- Unable to connect to the Network Share.
- Detailed Description
- Unable to connect to the Network Share due to one of the following: 1) Login credentials entered are incorrect. 2) Network is inaccessible. 3) System IP address conflicts with another system on the network.
- Recommended Response Action
- Verify the login credentials. Make sure the Network Share is accessible and the system IP address does not conflict with any other system on the network. If the problem persists, perform an AC power cycle and retry.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0067
- Message
- Unable to import operating system configuration file.
- Detailed Description
- The location of the operating system configuration file specified in the operation is not valid.
- Recommended Response Action
- Make sure that the specified source file path is correct and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0068
- Message
- Unable to retrieve the boot mode settings from BIOS.
- Detailed Description
- The BIOS boot mode settings could not be retrieved because of an internal issue.
- Recommended Response Action
- Exit the OS Deployment wizard and retry the operation. If the problem persists, exit Lifecycle Controller and perform an AC power cycle.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0070
- Message
- The Tech Support Report is successfully exported to the USB drive.
- Detailed Description
- The Tech Support Report is successfully exported to the USB drive.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC0071
- Message
- The Tech Support Report is successfully exported to the network share folder.
- Detailed Description
- The Tech Support Report is successfully exported to the network share folder.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC0072
- Message
- Unable to export the Tech Support Report to destination folder.
- Detailed Description
- Tech Support Report cannot be exported to the destination folder.
- Recommended Response Action
- Verify the following and retry the operation: 1) Destination folder is present. 2) Destination folder has sufficient free disk space. 3) Destination folder is not write-protected. If the issue persists, perform an AC power cycle operation, and then retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0073
- Message
- Unable to start operation with the current iDRAC version.
- Detailed Description
- The Repurpose or Retire system operation cannot be successfully started because the current version of iDRAC firmware does not support the operation.
- Recommended Response Action
- Update iDRAC firmware to the latest version and retry the operation. If the issue persists, contact your service provider.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0074
- Message
- Unable to start operation with the current iDRAC version.
- Detailed Description
- The export operation of Tech Support Report cannot be started because the current version of iDRAC firmware does not support the operation.
- Recommended Response Action
- Update iDRAC firmware to the latest version and retry the operation. If the issue persists, contact your service provider.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0075
- Message
- Unable to perform RAID operations because the selected controller is in HBA mode.
- Detailed Description
- Unable to perform RAID operations because the selected controller is in HBA mode.
- Recommended Response Action
- Do one of the following: 1) Retry the operation using other controllers that support RAID operations and are not in HBA mode. 2) Change the mode of the controller from HBA mode to RAID mode and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0076
- Message
- The following iDRAC internal storage partitions present in the system were not mounted during the system startup: arg1
- Arguments
- arg1 = partitions
- Detailed Description
- Lifecycle Controller detected that the iDRAC internal storage partitions identified in the message were not made available by BIOS during the boot process.
- Recommended Response Action
- No response action required. If the issue occurs consistently during system startup, restart the iDRAC and then restart the system. If the issue persists, contact your service provider.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC0077
- Message
- Unable to initiate the Repurpose or Retire System operation.
- Detailed Description
- iDRAC is unable to initiate the Repurpose or Retire System operation because the iDRAC is not responding or another operation is in progress.
- Recommended Response Action
- Retry the operation. If the problem persists, do one the following: 1) Check if there are other operations running on the iDRAC and wait for the operations to complete, and retry the operation. 2) Restart the server, and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC0101
- Message
- Unable to read available log records.
- Detailed Description
- Racadm is unable to read the available log records at this point. Retry the command.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0102
- Message
- The -m option is not supported by the interface being used.
- Detailed Description
- The option requested is not available on the interface being used.
- Recommended Response Action
- Refer to the help to get the list of options valid for the interface.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0103
- Message
- The -E option is not valid for the specified log.
- Detailed Description
- The specified log does not take in the -e option.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0104
- Message
- The -R option is not valid for the specified log.
- Detailed Description
- The specified log does not take in the -r option.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0105
- Message
- Invalid -m option. Try --more or refer help for proper usage
- Detailed Description
- The command does not take in the -m option.
- Recommended Response Action
- Refer the help text for getraclog command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0106
- Message
- The -u option is not supported on the current RAC configuration.
- Detailed Description
- The specified option is not supported on the RAC.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0107
- Message
- More than one option is not allowed with this command.
- Detailed Description
- The command takes in only one option which is the Session ID.
- Recommended Response Action
- Enter the command only with one option i.e. the Session ID
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0109
- Message
- No process information is currently available.
- Detailed Description
- There is no RAC diagnostic information available.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
SWC0110
- Message
- No build information is currently available.
- Detailed Description
- The build information is not available for racdump.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
SWC0111
- Message
- A server action command must be specified.
- Detailed Description
- The serveraction subcommand requires an option to be specified.
- Recommended Response Action
- Refer the help for serveraction subcommand, and enter a valid option.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0112
- Message
- Timeout while waiting for server to perform requested power action.
- Detailed Description
- A network time-out occurred while trying to perform the power action.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0113
- Message
- The -6 option can only be used in combination with the -d or -s option.
- Detailed Description
- The syntax of the setniccfg command is invalid.
- Recommended Response Action
- Refer the help text for setniccfg subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0114
- Message
- The -o option cannot be used with any other options.
- Detailed Description
- The syntax of the setniccfg command is invalid.
- Recommended Response Action
- Refer the help text for setniccfg subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0115
- Message
- The -s option cannot be used with any other options.
- Detailed Description
- The syntax of the setniccfg command is invalid.
- Recommended Response Action
- Refer the help text for setniccfg subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0116
- Message
- The -s option requires IP address, subnet mask, and gateway.
- Detailed Description
- The syntax of the setniccfg command is invalid.
- Recommended Response Action
- Refer the help text for setniccfg subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0117
- Message
- Invalid syntax. Both -f and -t must be specified.
- Detailed Description
- Invalid parameters passed to the function.
- Recommended Response Action
- Refer the help text for sslcertdownload subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0118
- Message
- Invalid syntax. -f must be specified.
- Detailed Description
- The syntax of the sslcertupload command is invalid.
- Recommended Response Action
- Refer the help text for sslcertupload subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0119
- Message
- Invalid certificate type specified with -t option.
- Detailed Description
- The syntax of the sslcertview command is invalid.
- Recommended Response Action
- Refer the help text for sslcertview subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0120
- Message
- Invalid syntax. Certificate type (-t) must be specified.
- Detailed Description
- The syntax of the sslcertview command is invalid.
- Recommended Response Action
- Refer the help text for sslcertview subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0121
- Message
- Invalid syntax. User index (-i) must be specified.
- Detailed Description
- The syntax of the sslcertview command is invalid.
- Recommended Response Action
- Refer the help text for sslcertview subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0122
- Message
- Invalid syntax. SSL key type (-t) must be specified.
- Detailed Description
- The syntax of the sslcertupload command is invalid.
- Recommended Response Action
- Refer the help text for sslcertupload subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0123
- Message
- The -s option is not valid with any other options.
- Detailed Description
- The syntax of the sslcsrgen command is invalid.
- Recommended Response Action
- Refer the help text for sslcsrgen subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0124
- Message
- The -u option requires -f to be specified.
- Detailed Description
- The syntax of the sslcsrgen command is invalid.
- Recommended Response Action
- Refer the help text for sslcsrgen subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0127
- Message
- Unable to open file for writing.
- Detailed Description
- The file may be write protected and hence could not be edited.
- Recommended Response Action
- Check if the file is write protected.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
SWC0128
- Message
- The Common Name (CN) field of the CSR Security group must\nbe configured before a CSR can be generated.
- Detailed Description
- The Common Name field is necessary for generating a CSR. It is not generated if Common Name is empty.
- Recommended Response Action
- Configure the Common Name field by using config command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0129
- Message
- Unable to send test email. Please make sure that your email alerts\nhave been configured correctly and connectivity to \nthe SMTP server exists.
- Detailed Description
- Racadm tool was not able to send a test email for the configuration.
- Recommended Response Action
- Check for the parameters mentioned in the message.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0130
- Message
- Trap at specified index is not currently enabled.
- Detailed Description
- The Trap needs to be set for the particular index for the testtrap to go through.
- Recommended Response Action
- Set cfgIpmiPetAlertEnable in cfgIpmiPet group using config subcommand for the corresponding index.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0131
- Message
- Trap destination address must be configured.
- Detailed Description
- The destination Ip address must be configured for the Trap.
- Recommended Response Action
- Set cfgIpmiPetAlertDestIpAddr in cfgIpmiPet group using config subcommand for the corresponding index.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0132
- Message
- Unable to send test trap. Please make sure that your trap\nhas been configured correctly and connectivity to \nthe destination endpoint exists.
- Detailed Description
- Either the destination Ip address is not reachable or the required values are not configured.
- Recommended Response Action
- Check for the connectivity to the configured Ip address.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0133
- Message
- Either connect or disconnect must be specified.
- Detailed Description
- Insufficient information provided.
- Recommended Response Action
- Specify either the connect or the disconnect option with the subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0140
- Message
- RAC reset operation initiated successfully. It may take up to a minute \nfor the RAC to come back online again.
- Detailed Description
- Success message.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0144
- Message
- Certificate successfully uploaded to the RAC. The RAC will now reset\nto enable the new certificate and may be offline temporarily.
- Detailed Description
- Success message.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0149
- Message
- Test trap sent successfully.
- Detailed Description
- The requested SNMP test trap alert was successfully sent.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0215
- Message
- Disable Remote File Started.Please check status using -s option to know Remote File Share is ENABLED or DISABLED.
- Detailed Description
- The process to disable the file share has started. Use the -s option to know more about the status.
- Recommended Response Action
- If required check the status using the -s option.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0216
- Message
- The -c option requires -l to also be specifed.
- Detailed Description
- The syntax of the command is incorrect.
- Recommended Response Action
- Refer to the help for remote image command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0217
- Message
- The -c option requires -u to also be specifed.
- Detailed Description
- The syntax of the command is incorrect.
- Recommended Response Action
- Refer to the help for remote image command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0218
- Message
- The -c option requires -p to also be specifed.
- Detailed Description
- The syntax of the command is incorrect.
- Recommended Response Action
- Refer to the help for remote image command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0219
- Message
- The -p option requires -c to also be specifed.
- Detailed Description
- The syntax of the command is incorrect.
- Recommended Response Action
- Refer to the help for remote image command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0220
- Message
- The -u option requires -c to also be specifed.
- Detailed Description
- The syntax of the command is incorrect.
- Recommended Response Action
- Refer to the help for remote image command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0221
- Message
- The -l option requires -c to also be specifed.
- Detailed Description
- The syntax of the command is incorrect.
- Recommended Response Action
- Refer to the help for remote image command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0222
- Message
- Invalid syntax. The -d option is not valid with -c.
- Detailed Description
- The syntax of the command is incorrect.
- Recommended Response Action
- Refer to the help for remote image command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0223
- Message
- Invalid syntax. The -d option is not valid with -p.
- Detailed Description
- The syntax of the command is incorrect.
- Recommended Response Action
- Refer to the help for remote image command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0224
- Message
- Invalid syntax. The -d option is not valid with -u.
- Detailed Description
- The syntax of the command is incorrect.
- Recommended Response Action
- Refer to the help for remote image command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0225
- Message
- Invalid syntax. The -d option is not valid with -l.
- Detailed Description
- The syntax of the command is incorrect.
- Recommended Response Action
- Refer to the help for remote image command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0226
- Message
- No valid directory service certificate exists
- Detailed Description
- The Remote/Firmware racadm did not find any AD/LDAP certificate at specified path.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
SWC0227
- Message
- Partition label exceeds maximum limit of 6 alphanumeric characters.
- Detailed Description
- Invalid values passed to the function.
- Recommended Response Action
- Enter a shorter path to the firmware image file.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0228
- Message
- Partition label must be an alphanumeric character string.
- Detailed Description
- Invalid values passed to the function.
- Recommended Response Action
- Enter a shorter Partition label.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0229
- Message
- Some Necessary tag(s) are missing: -i -o -e -t -f & -s must be specified for create partition.
- Detailed Description
- Insufficient arguments passed to the command.
- Recommended Response Action
- Refer the help text for vflashpartition command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0230
- Message
- vFlash not enabled.
- Detailed Description
- vFlash is not enabled. This may be because the user does not have enough privileges.
- Recommended Response Action
- Enable vFlash and re-try.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0231
- Message
- Partition of type \"image\" not supported on local racadm.
- Detailed Description
- The partition image type specified is not available on local racadm.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0232
- Message
- Remote RACADM commands are not supported on this iDRAC. To upgrade your iDRAC version, contact your service provider.
- Detailed Description
- Remote RACADM commands are not supported on the current iDRAC.
- Recommended Response Action
- If remote RACADM is a necessity, upgrade the iDRAC version.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0233
- Message
- No indexes are available to configure additional groups.
- Detailed Description
- Indexed groups in the configuration file is more than the indexed groups in iDRAC.
- Recommended Response Action
- Verify if the number of indexed groups available in iDRAC match the indexed groups in the configuration file. If it does not match, either reset the unecessary indexes on iDRAC or remove the extra groups from the configuration file.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
SWC0234
- Message
- Remote host is not reachable or connection is interrupted.
- Detailed Description
- The remote host specified for the ftp update is not reachable.
- Recommended Response Action
- Check the connectivity between iDRAC and the remote host used for the ftp update.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
SWC0237
- Message
- Key text appears to be corrupted.
- Detailed Description
- The key text in the public key specified is corrupt.
- Recommended Response Action
- Request for a valid public key from the system and re-try the command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0238
- Message
- Key is too long.
- Detailed Description
- The key specified by the public key is too long.
- Recommended Response Action
- Request for a valid public key from the system and re-try the command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0239
- Message
- The requested object is not allowed to be configured if IPv6 AutoConfig is enabled.
- Detailed Description
- The requested object is auto-assigned if IPv6 AutoConfig is enabled, and hence cannot be configured.
- Recommended Response Action
- Disable IPv6 AutoConfig and re-try the command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0240
- Message
- The IPv6 DNS Server IP address is not allowed to be configured if IPv6 DNS Server DHCP (cfgIPv6DNSServersFromDHCP6) is enabled
- Detailed Description
- The requested object is auto-assigned if DNS Server DHCP is enabled, and hence cannot be configured.
- Recommended Response Action
- Disable DNS Server DHCP and re-try the command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0241
- Message
- Power Cap Enable not set. Unable to modify this property
- Detailed Description
- To modify this property, set the Power Cap Enable option.
- Recommended Response Action
- Set the Power Cap Enable object and modify the required property.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0242
- Message
- A required license is missing or expired. Obtain an appropriate license and try again, or contact your service provider for additional details.
- Detailed Description
- The license is missing or expired. This will result in the loss of functionality that is specific to the features supported by the license.
- Recommended Response Action
- Import an appropriate license to iDRAC. If you do not know which license to install, contact your service provider.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
SWC0243
- Message
- Certificate regenerated successfully and webserver restarted
- Detailed Description
- SSL Certificate is regenerated successfully and the Web server is restarted.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0244
- Message
- Invalid Fully Qualified Device Descriptor (FQDD).
- Detailed Description
- The specified Fully Qualified Device Descriptor (FQDDs) system component name is invalid.
- Recommended Response Action
- Verify that the correct Fully Qualified Device Descriptor (FQDD) system component name is specified. See the help text (The help text for the get subcommand can be obtained by running "racadm help get") or documentation for valid FQDD system component names.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0245
- Message
- Failed to set object value because local configuration using RACADM is disabled.
- Detailed Description
- Local configuration using RACADM is disabled. This limits local configuration privileges such as resetting object values.
- Recommended Response Action
- Within group cfgRacTuning set the property cfgRacTuneLocalConfigDisable to 0.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0246
- Message
- Value specified is invalid: Valid range is arg1 .
- Arguments
- arg1 = index
- Detailed Description
- The specified value is outside of the valid range.
- Recommended Response Action
- Verify that a valid value is specified. See the help text or documentation for valid values.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0248
- Message
- Invalid command syntax.
- Detailed Description
- The specified command has invalid syntax.
- Recommended Response Action
- Verify that the correct command syntax is specified. See the help text or documentation for valid commands.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0249
- Message
- Invalid syntax. The requestsed subcommand requires -i arg1 to be specified.
- Arguments
- arg1 = index
- Detailed Description
- The specified parameter needs to be given with its legal value.
- Recommended Response Action
- Enter the proper index preceeded by -i.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0250
- Message
- Invalid syntax. The specified subcommand does not require any options.
- Detailed Description
- Extra parameters were passed.
- Recommended Response Action
- Enter the subcommand without any options.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0251
- Message
- Invalid index value. Only index values arg1 - arg2 are permitted.
- Arguments
- arg1 = number, arg2 = number
- Detailed Description
- The value of specified parameter is invalid.
- Recommended Response Action
- Enter the index value as specified by the message.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0252
- Message
- No options were specified. The subcommand requires options to be used.
- Detailed Description
- Invalid number of arguments were passed to the command.
- Recommended Response Action
- Refer the help text for the command, and enter the required parameters.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0253
- Message
- Unable to allocate memory needed to perform operation.
- Detailed Description
- Unable to allocate memory to perform the operation, see the inserted comment.
- Recommended Response Action
- Power Cycle the system and re-enter the command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0254
- Message
- Unable to perform requested operation. \nIf the operation attempted was to configure DRAC, possible reason may be that \nLocal Configuration using RACADM is disabled.
- Detailed Description
- Local Configuration using RACADM may be disabled.
- Recommended Response Action
- Check if the Local Configuration using RACADM is disabled and enable it through GUI.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0257
- Message
- Invalid syntax. Too many options specified.
- Detailed Description
- Invalid number of arguments were passed to the command.
- Recommended Response Action
- Refer the help text for the command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0258
- Message
- Insufficient resources to perform operation.
- Detailed Description
- Insuffcient resources to execute the command.
- Recommended Response Action
- Power Cycle the system and re-enter the command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
SWC0259
- Message
- Invalid group specified.
- Detailed Description
- The value of specified parameter is invalid.
- Recommended Response Action
- Refer the list of groups and enter a valid option.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0260
- Message
- Invalid object specified.
- Detailed Description
- The value of specified parameter is invalid.
- Recommended Response Action
- Refer the list of objects in the corresponding group.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0261
- Message
- The specified option is not supported with the interface being used.
- Detailed Description
- The option requested is not available on the interface being used.
- Recommended Response Action
- Refer to the help to get the list of commands/options valid for the interface.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0262
- Message
- Unable to perform operation. Please make sure RAC controller and \nappropriate IPMI drivers are installed.
- Detailed Description
- The IPMI drivers or the RAC contorller may not be installed.
- Recommended Response Action
- Check if the required modules are installed.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
SWC0263
- Message
- Specified path is too long.
- Detailed Description
- The length of path to the firmware image is longer than the specified value.
- Recommended Response Action
- Enter a shorter path to the firmware image file.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0264
- Message
- Resource currently in use by another process. Please retry again later.
- Detailed Description
- The resources required for the execution are in use by another process
- Recommended Response Action
- Wait for the process to release the resources and try again.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0265
- Message
- This option is not supported on this type of DRAC.
- Detailed Description
- The option requested is not available on the DRAC being used.
- Recommended Response Action
- Refer to the help to get the list of commands/options valid for the DRAC.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0266
- Message
- Unable to perform the requested operation. Make sure SD card is inserted.
- Detailed Description
- The SD card may not be inserted/inserted properly.
- Recommended Response Action
- Ensure that the SD card is inserted in the server.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0267
- Message
- Unable to perform the requested operation. Make sure a non write protected SD card is inserted.
- Detailed Description
- Unable to edit the SD card, since it is write protected.
- Recommended Response Action
- Check if the SD card is write protected. If yes, disable the write protection.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0269
- Message
- Unable to clear the RAC log. \nPossible reason may be that Local Configuration using RACADM is disabled.
- Detailed Description
- Local Configuration using RACADM may be disabled.
- Recommended Response Action
- Check if the Local Configuration using RACADM is disabled and enable it through GUI.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0270
- Message
- Unable to clear the SEL. \nPossible reason may be that Local Configuration using RACADM is disabled.
- Detailed Description
- Local Configuration using RACADM may be disabled.
- Recommended Response Action
- Check if the Local Configuration using RACADM is disabled and enable it through GUI.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0271
- Message
- Invalid syntax. The -f option is only valid with -p and -c.
- Detailed Description
- The syntax for the config command is invalid.
- Recommended Response Action
- Refer to the help text for the config subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0272
- Message
- Invalid syntax. The -g option is only valid with -o, -i, and -c.
- Detailed Description
- The syntax for the config command is invalid.
- Recommended Response Action
- Refer to the help text for the config subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0273
- Message
- Invalid syntax. The -g option requires -o to also be specified.
- Detailed Description
- The syntax for the config command is invalid.
- Recommended Response Action
- Refer to the help text for the config subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0274
- Message
- Invalid syntax. An object value must be specified.
- Detailed Description
- The value of specified parameter is invalid.
- Recommended Response Action
- Enter the same command with a legal value to the object.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0275
- Message
- Invalid syntax. The -c option is only valid with -f or -g.
- Detailed Description
- The syntax for the config command is invalid.
- Recommended Response Action
- Refer to the help text for the config subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0276
- Message
- Invalid syntax. The -p option is only valid with -f.
- Detailed Description
- The syntax for the config command is invalid.
- Recommended Response Action
- Refer to the help text for the config subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0277
- Message
- Invalid syntax. The -i option is only valid with -g and -o.
- Detailed Description
- The syntax for the config command is invalid.
- Recommended Response Action
- Refer to the help text for the config subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0278
- Message
- Invalid group or object specified.
- Detailed Description
- The value of specified parameter is invalid.
- Recommended Response Action
- Enter the values for the group name and object name correctly.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0279
- Message
- The specified group is not indexed and does not support -i.
- Detailed Description
- The group is not indexed and does not require an index to be specified.
- Recommended Response Action
- Enter the command without the index.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0280
- Message
- The indexed group specified requires -i arg1 .
- Arguments
- arg1 = index
- Detailed Description
- The group is indexed and an index needs to be specified.
- Recommended Response Action
- Enter the command with a valid index for the group.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0281
- Message
- The specified object is READ ONLY and cannot be modified.
- Detailed Description
- The value being modified is READ only.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0282
- Message
- The specified object is READ ONLY for this index and cannot be modified.
- Detailed Description
- The value being modified is READ only.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0283
- Message
- The specified object value is not valid.
- Detailed Description
- The value given for the object is not valid.
- Recommended Response Action
- Enter a valid value for the corresponding object.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0284
- Message
- Failed to set the object value. \nPossible reason may be that Local Configuration using RACADM is disabled.
- Detailed Description
- Local Configuration using RACADM may be disabled.
- Recommended Response Action
- Check if the Local Configuration using RACADM is disabled and enable it through GUI.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0286
- Message
- Modifying the user configuration at index 1 is not allowed.
- Detailed Description
- Objects in the cfgUserAdmin group corresponding to index 1 cannot be modified.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0287
- Message
- Invalid entry in configuration file.
- Detailed Description
- The value of a parameter in the config file is invalid.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0288
- Message
- Object arg1 in arg2 group must be specified. Line: arg3
- Arguments
- arg1 = object name, arg2 = group name, arg3 = line no.
- Detailed Description
- The object specified in the message in the group specified in the message is not configured.
- Recommended Response Action
- Configure the object specified in the message in specified group, before performing a config to file action.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0289
- Message
- Invalid value in config file. Group: arg1 , Object: arg2 , Value: \" arg3 \", Line [ arg4 }
- Arguments
- arg1 = Group Name, arg2 = Object Name, arg3 = Value, arg4 = Line No.
- Detailed Description
- The specified objec value is invalid.
- Recommended Response Action
- Configure the specified object and assign a valid value.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0290
- Message
- Failed to configure object. Group: arg1 , Object : arg2
- Arguments
- arg1 = Group Name, arg2 = Object Name
- Detailed Description
- Failed to configure the object specified in the error message.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0291
- Message
- Another object exists with the specified value. Duplicate values are\nnot allowed for the requested object.
- Detailed Description
- Another object of the same value exists. Typically in the case of username.
- Recommended Response Action
- Change the specified value and re-try.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0292
- Message
- The specified object at index arg1 does not exist.
- Arguments
- arg1 = index number
- Detailed Description
- The queried object does not exist at the specified index.
- Recommended Response Action
- Check for the objects available at the specified index and re-try.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0293
- Message
- The specified object is not recognized by iDRAC.
- Detailed Description
- The specified object is not present in the iDRAC.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0294
- Message
- Invalid group name specified.
- Detailed Description
- The group name specified is incorrect.
- Recommended Response Action
- Refer to the list of groups available and choose the correct one.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0295
- Message
- Invalid object name specified.
- Detailed Description
- The object name specified is incorrect.
- Recommended Response Action
- Refer to the list of objects in the group and choose the correct one.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0296
- Message
- The specified value is not allowed to be configured if the user name \nor password is blank.
- Detailed Description
- Either the password field or the username field is empty.
- Recommended Response Action
- Enter the command with the username and password.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0297
- Message
- Unable to remove passwords because file could not be saved.
- Detailed Description
- After the Groups are downloaded to a file, the passwords are to be deleted.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0298
- Message
- The specified object value cannot be configured if local configuration is disabled or smart card logon is enabled. If smart card logon is enabled, serial, SSH, telnet and IPMIoverLAN is disabled by force and cannot be enabled.
- Detailed Description
- The specified object value cannot be configured if local configuration is disabled or smart card logon is enabled. If smart card logon is enabled, serial, SSH, telnet and IPMIoverLAN is disabled by force and cannot be enabled.
- Recommended Response Action
- Enable Local Configuration (through GUI) or Disable Smart Card Logon to change the value.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0302
- Message
- The -s option is not valid with any other option.
- Detailed Description
- The syntax of the fwupdate command is invalid.
- Recommended Response Action
- Refer the help text for fwupdate subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0303
- Message
- The -r option is not valid with any other option.
- Detailed Description
- The syntax of the fwupdate command is invalid.
- Recommended Response Action
- Refer the help text for fwupdate subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0304
- Message
- The -g option requires -u to also be specifed.
- Detailed Description
- The syntax of the fwupdate command is invalid.
- Recommended Response Action
- Refer the help text for fwupdate subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0305
- Message
- The -p option requires -u to also be specifed.
- Detailed Description
- The syntax of the fwupdate command is invalid.
- Recommended Response Action
- Refer the help text for fwupdate subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0306
- Message
- The -a option requires -g and -u to also be specifed.
- Detailed Description
- The syntax of the fwupdate command is invalid.
- Recommended Response Action
- Refer the help text for fwupdate subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0307
- Message
- The -d option requires -p or -g to also be specifed.
- Detailed Description
- The syntax of the fwupdate command is invalid.
- Recommended Response Action
- Refer the help text for fwupdate subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0308
- Message
- The -d option requires -g to also be specifed.
- Detailed Description
- The syntax of the fwupdate command is invalid.
- Recommended Response Action
- Refer the help text for fwupdate subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0309
- Message
- The -p option is not supported with the interface being used.
- Detailed Description
- The platform does not support the specified functionality of fwupdate.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0310
- Message
- Invalid syntax. The -f is not valid with the option specified.
- Detailed Description
- The syntax of the getconfig command is invalid.
- Recommended Response Action
- Refer the help text for getconfig subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0311
- Message
- Invalid syntax. The -g option is only valid with -i and -o options.
- Detailed Description
- The syntax of the getconfig command is invalid.
- Recommended Response Action
- Refer the help text for getconfig subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0312
- Message
- Invalid syntax. The -u option is not valid with any other options.
- Detailed Description
- The syntax of the getconfig command is invalid.
- Recommended Response Action
- Refer the help text for getconfig subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0313
- Message
- Invalid syntax. The -h option is not valid with any other options.
- Detailed Description
- The syntax of the getconfig command is invalid.
- Recommended Response Action
- Refer the help text for getconfig subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0314
- Message
- Invalid syntax. The -o option requires -g to be specified also.
- Detailed Description
- The syntax of the getconfig command is invalid.
- Recommended Response Action
- Refer the help text for getconfig subcommand.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0317
- Message
- The number of records to display must be greater than zero.
- Detailed Description
- The value for -c must be greater than zero.
- Recommended Response Action
- Enter a value greater than zero, for the option -c.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0318
- Message
- The starting record must be greater than zero.
- Detailed Description
- The value for -s must be greater than zero.
- Recommended Response Action
- Enter a value greater than zero, for the option -s.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0319
- Message
- The -i option is not valid with any other options.
- Detailed Description
- The syntax for the getraclog command is invalid.
- Recommended Response Action
- Refer the help text for getraclog command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0320
- Message
- Unable to get the number of records available.
- Detailed Description
- Racadm tool failed to get the total number of records.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0322
- Message
- Starting record specified exceeds number of records available.
- Detailed Description
- The starting record value has to be lesser than the number of records available.
- Recommended Response Action
- Get the number of records available, and then run the command. If the command is gettracelog, try executing the command again.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0323
- Message
- Number of records specified exceeds number of records available.
- Detailed Description
- The number of records specified to be displayed should be lesser than number of records available.
- Recommended Response Action
- Get the number of records available, and then run the command.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0324
- Message
- There are no records available to display.
- Detailed Description
- There are no records to display. This might be a result of the log being cleared.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0325
- Message
- The specified object is WRITE-ONLY and cannot be displayed.
- Detailed Description
- The requested property is write-only.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0700
- Message
- iDRAC is not ready. The configuration values cannot be accessed. Please retry after a few minutes.
- Detailed Description
- iDRAC7 is not ready or is busy and is not responding to iDRAC7 Settings IPMI requests.
- Recommended Response Action
- Turn off the system, Remove AC. Wait for 5 seconds. Connect AC. Turn it on.
- Category
- System Health (SWC = Software Config)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
SWC0701
- Message
- Power capping is enabled.
- Detailed Description
- Power capping is enabled and sets user-defined power capping limits for the system.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0702
- Message
- Power capping is disabled.
- Detailed Description
- Power capping is disabled and sets recommended limits for the system.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC0717
- Message
- iDRAC Local Configuration is disabled. iDRAC Settings are accessed in read-only mode.
- Detailed Description
- For security reasons, the local configuration is disabled. Enable local configuration from the iDRAC Web interface
- Recommended Response Action
- Enable iDRAC local configuration from iDRAC Web interface.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC0722
- Message
- Error occurred while resetting to defaults. The reset command was not accepted.
- Detailed Description
- iDRAC is processing a previous reset to default command.
- Recommended Response Action
- Retry after a few minutes.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
SWC0723
- Message
- Error occurred while Resetting to defaults. The Reset status is not available.
- Detailed Description
- iDRAC is not responding to the current Reset status query.
- Recommended Response Action
- Retry after a few minutes.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
SWC0724
- Message
- Error occurred while Resetting to defaults due to a timeout.
- Detailed Description
- Resetting to defaults did not complete within the maximum process alloted time.
- Recommended Response Action
- Retry after a few minutes.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
SWC1909
- Message
- User ID arg1 RAC Privilege has been changed.
- Arguments
- arg1 = username
- Detailed Description
- The privilege level of the iDRAC User ID indicated in the message has been changed.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC1917
- Message
- HTTPS redirection is disabled.
- Detailed Description
- HTTP to HTTPS redirection is disabled. Any iDRAC connection made over the HTTP port (default port number 80) will no longer be redirected to the secure HTTPS port (default port number 443). This will make the connections insecure as the data transmitted over the port is no longer encrypted.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC1918
- Message
- HTTPS redirection is enabled.
- Detailed Description
- HTTP to HTTPS redirection is enabled. Any iDRAC connection made over the HTTP port (default port number 80) will be redirected to the secure HTTPS port (default port number 443).
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC1922
- Message
- User arg1 has successfully modified the server configuration by using Quick Sync.
- Arguments
- arg1 = user name
- Detailed Description
- The user identified in the message has successfully modified the server configuration by using Quick Sync.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC1923
- Message
- Unable to modify the server configuration by using Quick Sync because invalid credentials are entered.
- Detailed Description
- The server configuration cannot be modified by using Quick Sync because invalid credentials are entered.
- Recommended Response Action
- Make sure that correct user name and password are entered, and then retry the operation.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC1924
- Message
- Unable to modify the server configuration by using Quick Sync.
- Detailed Description
- The server configuration cannot be modified by using Quick Sync because issues were found with the configuration information.
- Recommended Response Action
- Review the server configuration operation results and correct any issues detected, then retry the operation.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC1925
- Message
- The iDRAC Quick Sync access feature is set to the Disabled mode.
- Detailed Description
- The iDRAC Quick Sync access feature is set to the Disabled mode.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC1927
- Message
- The iDRAC Quick Sync access feature is set to the read-only mode.
- Detailed Description
- The iDRAC Quick Sync access feature is set to the read-only mode.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC1928
- Message
- The iDRAC Quick Sync access feature is set to the read-write mode.
- Detailed Description
- The iDRAC Quick Sync access feature is set to the read-write mode.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC1929
- Message
- The iDRAC Quick Sync inactivity timeout value is set to arg1 .
- Arguments
- arg1 = timeout period
- Detailed Description
- The iDRAC Quick Sync inactivity timeout value is set to the value identified in the message.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC1930
- Message
- The iDRAC Quick Sync inactivity timeout feature is enabled.
- Detailed Description
- The iDRAC Quick Sync feature is set to automatically disable after a specified inactivity time.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC1931
- Message
- The iDRAC Quick Sync inactivity timeout configuration is disabled.
- Detailed Description
- The iDRAC Quick Sync inactivity timeout configuration is disabled. The iDRAC Quick Sync feature will remain available after pressing the activate button.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC4004
- Message
- A firmware or software incompatibility detected between iDRAC in slot arg1 and CMC.
- Arguments
- arg1 = number
- Detailed Description
- FlexAddress is not implemented in one of the versions of firmware. Please update the firmware.
- Recommended Response Action
- Check firmware versions of iDRAC and CMC. Update to latest version.
- Category
- System Health (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- Trap/EventID
- 2338
SWC4005
- Message
- A firmware or software incompatibility was corrected between iDRAC in slot arg1 and CMC.
- Arguments
- arg1 = number
- Detailed Description
- None
- Recommended Response Action
- No response action is required.
- Category
- System Health (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- Trap/EventID
- 2339
SWC4006
- Message
- A firmware or software incompatibility detected between system BIOS in slot arg1 and CMC.
- Arguments
- arg1 = number
- Detailed Description
- FlexAddress is not implemented in one of the versions of firmware. Please update the firmware.
- Recommended Response Action
- Check firmware versions of BIOS and CMC. Update to latest version.
- Category
- System Health (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- Trap/EventID
- 2338
SWC4007
- Message
- A firmware or software incompatibility was corrected between system BIOS in slot arg1 and CMC.
- Arguments
- arg1 = number
- Detailed Description
- None
- Recommended Response Action
- No response action is required.
- Category
- System Health (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- Trap/EventID
- 2339
SWC4008
- Message
- A firmware or software incompatibility detected between CMC 1 and CMC 2.
- Detailed Description
- FlexAddress is not implemented in one of the versions of firmware. Please update the firmware.
- Recommended Response Action
- Check firmware versions. Update CMC 1 and CMC 2 firmware to match.
- Category
- System Health (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- Trap/EventID
- 2338
SWC4009
SWC4010
- Message
- arg1 arg2 in Server- arg3 requires a version of Chassis Management Controller (CMC) firmware 5.0 or later for using the NParEP (ARI mode) functions.
- Arguments
- arg1 = network device name, arg2 = network device location, arg3 = server location
- Detailed Description
- The current CMC firmware does not support the ARI Mode advanced features available in the network device on the server identified in the message.
- Recommended Response Action
- Update the CMC firmware to the latest version and to enable access to the advanced features available in the network device.
- Category
- System Health (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC4011
- Message
- A firmware or software incompatibility is automatically corrected between the arg1 arg2 in Server- arg3 and the Chassis Management Controller (CMC).
- Arguments
- arg1 = network device name, arg2 = network device location, arg3 = server location
- Detailed Description
- A firmware or software incompatibility was automatically corrected between the network device in the Server identified in the message and the Chassis Management Controller (CMC).
- Recommended Response Action
- No response action is required.
- Category
- System Health (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC4012
- Message
- A firmware or software incompatibility is detected between arg1 arg2 and arg3 arg4 .
- Arguments
- arg1 = first component name, arg2 = first component location, arg3 = second component name, arg4 = second component location
- Detailed Description
- The system has detected a firmware or software incompatibility between the components identified in the message. A mismatch between component versions may cause the system to not function appropriately.
- Recommended Response Action
- Update the firmware or software of the components identified in the message. For information about the identified components, see the product documentation available at the service provider support site.
- Category
- System Health (SWC = Software Config)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2337
SWC4013
- Message
- A firmware or software incompatibility was corrected between arg1 arg2 and arg3 arg4 .
- Arguments
- arg1 = first component name, arg2 = first component location, arg3 = second component name, arg4 = second component location
- Detailed Description
- A firmware or software incompatibility was corrected between the components identified in the message.
- Recommended Response Action
- No response action is required.
- Category
- System Health (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- Trap/EventID
- 2339
SWC5003
- Message
- System Controller (SC) has either stopped functioning or is updating a firmware version.
- Detailed Description
- The System Controller (SC) has either stopped functioning or is updating a firmware version.
- Recommended Response Action
- Make sure that the System Controller is functioning.
- Category
- System Health (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- No alerts are applicable for this message
SWC5004
- Message
- System Controller (SC) has restarted functioning.
- Detailed Description
- System Controller (SC) has started functioning again because either a server health issue is resolved or SC has completed a firmware update process.
- Recommended Response Action
- No response action required.
- Category
- System Health (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC5005
- Message
- Unable to update the System Controller (SC) firmware
- Detailed Description
- The System Controller (SC) firmware cannot be updated. For information about the causes, see SEL Event Data Byte 2.
- Recommended Response Action
- Retry the SC firmware update operation. If the issue persists, try updating by using a different firmware update file.
- Category
- Updates (SWC = Software Config)
- Severity
- Severity 1 (Critical)
- No alerts are applicable for this message
SWC5006
- Message
- System Controller (SC) Firmware Update Successful
- Detailed Description
- System Controller (SC) reported a successful Firmware Update
- Recommended Response Action
- No response action required.
- Category
- Updates (SWC = Software Config)
- Severity
- Severity 3 (Informational)
- No alerts are applicable for this message
SWC8500
- Message
- Unable to generate Profile with [ arg1 ] settings.
- Arguments
- arg1 = number of entries
- Detailed Description
- Unable to communicate with iDRAC.
- Recommended Response Action
- Check if iDRAC is ready and system is running properly. Utilize the RACADM command by running "racadm getversion" to list all the servers and make sure the iDRAC version is displayed. If the iDRAC is listed as Not Ready then wait until it becomes ready. A Virtual Reseat may be required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC8501
- Message
- Unable to generate Profile.
- Detailed Description
- Unable to communicate with iDRAC.
- Recommended Response Action
- Check if iDRAC is ready and system is running properly. Utilize the RACADM command by running "racadm getversion" to list all the servers and make sure the iDRAC version is displayed. If the iDRAC is listed as Not Ready then wait until it becomes ready. A Virtual Reseat may be required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC8502
- Message
- A Profile is successfully generated with [ arg1 ] settings.
- Arguments
- arg1 = settings count
- Detailed Description
- A Profile is succesfully generated with the number of settings identified in the message.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8503
- Message
- arg1 Profile is renamed to arg2
- Arguments
- arg1 = profile name, arg2 = new profile name
- Detailed Description
- The Profile identified in the message has been renamed.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8504
- Message
- arg1 Profile renamed to arg2 and description edited.
- Arguments
- arg1 = profile name, arg2 = new profile name
- Detailed Description
- The Profile identified in the message was renamed and the description for the Profile was edited.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8505
- Message
- arg1 Profile description edited.
- Arguments
- arg1 = profile name
- Detailed Description
- The description for the Profile identified in the message was edited.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8508
- Message
- Unable to capture Profile from server in slot arg1
- Arguments
- arg1 = slot number
- Detailed Description
- Unable to communicate with iDRAC.
- Recommended Response Action
- Check if iDRAC is ready and system is running properly. Utilize the RACADM command by running "racadm getversion" to list all the servers and make sure the iDRAC version is displayed. If the iDRAC is listed as Not Ready then wait until it becomes ready. A Virtual Reseat may be required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC8509
- Message
- Unable to apply arg1 Profile to server in slot arg2
- Arguments
- arg1 = profile name, arg2 = slot number
- Detailed Description
- Unable to communicate with iDRAC.
- Recommended Response Action
- Check if iDRAC is ready and system is running properly. Utilize the RACADM command by running "racadm getversion" to list all the servers and make sure the iDRAC version is displayed. If the iDRAC is listed as Not Ready then wait until it becomes ready. A Virtual Reseat may be required. The Lifecycle log in the server identified in the message may have additional information about the inability of the iDRAC to apply Profile settings.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC8510
- Message
- Unable to apply arg1 Profile to requested Server(s)
- Arguments
- arg1 = profile name
- Detailed Description
- Unable to communicate with the iDRAC of the requested Server.
- Recommended Response Action
- Check if iDRAC is ready and system is running properly. Utilize the RACADM command by running "racadm getversion" to list all the servers and make sure the iDRAC version is displayed. If the iDRAC is listed as Not Ready then wait until it becomes ready. A Virtual Reseat may be required. The Lifecycle log in the server may have additional information about the inability of the iDRAC to apply Profile settings.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC8512
- Message
- Unable to add User arg1 : arg2 - arg3
- Arguments
- arg1 = user name, arg2 = error code, arg3 = error message
- Detailed Description
- Unable to add user name identified in the message. The reason for this issue is described with the error code in the message.
- Recommended Response Action
- Correct the error described in the message and retry the operation after a few minutes.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8514
- Message
- Unable to delete User arg1 : arg2 - arg3
- Arguments
- arg1 = user name, arg2 = error code, arg3 = error message
- Detailed Description
- Unable to delete the user name identified in the message.
- Recommended Response Action
- Make sure: 1) The login credentials for the operation have user config administration privilege, 2) The user name given is valid. If the issue persists, restart the CMC and retry the operation.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8515
- Message
- Successfully modified privileges of User arg1 .
- Arguments
- arg1 = user name
- Detailed Description
- Successfully modified privileges of User identified in the message.
- Recommended Response Action
- No response action is required.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8516
- Message
- Unable to modify privileges of User arg1 : arg2 - arg3
- Arguments
- arg1 = user name, arg2 = error code, arg3 = error message
- Detailed Description
- Unable to modify privileges of the User identified in the message.
- Recommended Response Action
- Make sure: 1) The login credentials for the operation have user config administration privilege, 2) The user name given is valid. If the issue persists, restart the CMC and retry the operation.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8517
- Message
- Successfully modified password of User arg1 .
- Arguments
- arg1 = user name
- Detailed Description
- Successfully modified the password for the User identified in the message.
- Recommended Response Action
- No response action is required.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8518
- Message
- Unable to modify password of User arg1 : arg2 - arg3
- Arguments
- arg1 = user name, arg2 = error code, arg3 = error message
- Detailed Description
- Unable to modify the password of the User identified in the message.
- Recommended Response Action
- Make sure: 1) The login credentials for the operation have user config administration privilege, 2) The user name and password given are valid. If the issue persists, restart the CMC and retry the operation.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8519
- Message
- Successfully modified user name from arg1 to arg2 .
- Arguments
- arg1 = original user name, arg2 = new user name
- Detailed Description
- The user name identified in the message was successfully modified.
- Recommended Response Action
- No response action is required.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8520
- Message
- Unable to modify user name from arg1 to arg2 : arg3 - arg4
- Arguments
- arg1 = original user name, arg2 = new_user name, arg3 = error code, arg4 = error message
- Detailed Description
- Unable to modify the user name specified in the message.
- Recommended Response Action
- Make sure: 1) The login credentials for the operation have user config administration privilege, 2) The user name given is valid. If the issue persists, restart the CMC and retry the operation.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8521
- Message
- Unable to modify timeout for session: arg1 : arg2 - arg3
- Arguments
- arg1 = SER/TEL/SSH/GUI/RAC/KVM/ERR, arg2 = error code, arg3 = error message
- Detailed Description
- Unable to modify the timeout for the session.
- Recommended Response Action
- Make sure: 1) The login credentials for the operation have chassis config administration privilege, 2) The session timeout given is valid. If the issue persists, restart the CMC and retry the operation.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8522
- Message
- Chassis Group Leader update of member arg1 configuration successful.
- Arguments
- arg1 = member id
- Detailed Description
- Successfully completed a configuration sync with the member identified in the message.
- Recommended Response Action
- No response action required.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8523
- Message
- Unable to complete Chassis Group Leader update of member arg1 .
- Arguments
- arg1 = DNS or IP address
- Detailed Description
- Unable to complete a configuration sync with the member identified in the message.
- Recommended Response Action
- Check the communications between the Chassis Group Leader and the member. Run the RACADM command "racadm ping <DNS or IP address> " to check the communications. If the communications are not functional, resolve the communications issue. If the communications are functional, remove the member from the group and re-add the member. If the issue persists, contact your service provider.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC8524
- Message
- Unable to add arg1 to Chassis Group because a member already exists with the same addressing information.
- Arguments
- arg1 = target
- Detailed Description
- A Chassis Group member already exists with the same hostname or IP address information as the target identified in the message.
- Recommended Response Action
- No response action is required.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8525
- Message
- Unable to add member to Chassis Group. Maximum members supported is arg1 .
- Arguments
- arg1 = maximum number of members
- Detailed Description
- Unable to add member because the maximum number of Chassis Group members indicated in the message has been reached.
- Recommended Response Action
- Try removing an existing member and retry the operation.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8526
- Message
- Unable to delete Chassis Group member arg1 ( arg2 )
- Arguments
- arg1 = member id, arg2 = DNS or IP address of member
- Detailed Description
- Unable to delete Chassis Group member identified in the message. Another user may have deleted the member before the operation or the group may have been disbanded.
- Recommended Response Action
- Make sure the member identified in the message exists as a member of the Chassis Group. Use the CMC web interface to select the lead chassis, select the setup tab, and then select the group administration sub tab and check if the member exists. If the member exists, restart the group leader and retry the operation.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8527
- Message
- Chassis Management Controller is unable to update the iDRAC user name to "root".
- Detailed Description
- Chassis Management Controller unable to update the IDRAC root user username as root. This can happen if the communication to the iDRAC from CMC is non-functional or if the username supplied is not valid.
- Recommended Response Action
- Make sure the user name is valid. If communication with iDRAC is not successful, reset the iDRAC. Retry the operation after a few minutes.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8528
- Message
- Chassis Management Controller is unable to update the iDRAC root password.
- Detailed Description
- The Chassis Management Controller is unable to update the IDRAC "root" user password. This can happen if the communication to the iDRAC from CMC is non-functional or if the password entered is not valid.
- Recommended Response Action
- Make sure the password is valid. If communications with the iDRAC is not functioning, reset the iDRAC and retry the operation after a few minutes. Run the RACADM command "racadm ping server-<slot number> " to check the communications. If the communications are not functional, restart the iDRAC by performing a Virtual Reseat of the server using the RACADM command "racadm racreset -m server-<slot id>".
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8529
- Message
- Chassis Management Controller unable to enable the iDRAC root user.
- Detailed Description
- The Chassis Management Controller is unable to enable the iDRAC root user. This can happen if the communication to the iDRAC from CMC is non-functional or iDRAC is rebooting
- Recommended Response Action
- If communications with the iDRAC is not functioning, reset the iDRAC and retry the operation after a few minutes. Run the RACADM command "racadm ping server-<slot number> " to check the communications. If the communications are not functional, restart the iDRAC by performing a Virtual Reseat of the server using the RACADM command "racadm racreset -m server-<slot id>".
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8530
- Message
- Chassis Management Controller unable to set administrator access to the iDRAC root user.
- Detailed Description
- The Chassis Management Controller is unable to set the server administrator access to the iDRAC root user. This can happen if the communication to the iDRAC from CMC is non-functional or the iDRAC is rebooting
- Recommended Response Action
- If communications with the iDRAC is not functioning, reset the iDRAC and retry the operation after a few minutes. Run the RACADM command "racadm ping server-<slot number> " to check the communications. If the communications are not functional, restart the iDRAC by performing a Virtual Reseat of the server using the RACADM command "racadm racreset -m server-<slot id>".
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8531
- Message
- Chassis Management Controller unable to set iDRAC administrator role for root user account.
- Detailed Description
- The Chassis Management Controller is unable to set the administrator role for the iDRAC root user. This can happen if the communication to the iDRAC from CMC is non-functional or iDRAC is rebooting.
- Recommended Response Action
- If communications with the iDRAC is not functioning, reset the iDRAC and retry the operation after a few minutes. Run the RACADM command "racadm ping server-<slot number> " to check the communications. If the communications are not functional, restart the iDRAC by performing a Virtual Reseat of the server using the RACADM command "racadm racreset -m server-<slot id>".
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8532
- Message
- Chassis Management Controller is unable to set chassis assigned QuickDeploy IP addresses because the starting IP address cannot accommodate all iDRACs.
- Detailed Description
- The starting IP address specified cannot accommodate all the servers. The starting iDRAC IPv4 Address specifies the static IPv4 address of the iDRAC located in the first slot. The static IPv4 address of each subsequent iDRAC is calculated as a slot number increment of this IPv4 address.
- Recommended Response Action
- Make sure there are enough IPv4 addresses for all the iDRACs and then retry the operation.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8533
- Message
- Unable to complete delete all keys operation for service accounts for all slots due to problem saving key file.
- Detailed Description
- The delete all keys for service accounts for all slots operation did not complete successfully due to problems encountered while saving the key file.
- Recommended Response Action
- Retry the operation. If the issue persists, contact your service provider.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8534
- Message
- All keys deleted for all slots of service account.
- Detailed Description
- All keys saved in the Chassis Management Controller for PK SSH Authentication are deleted.
- Recommended Response Action
- No response action is required.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8535
- Message
- Unable to add key for slot arg1 of service account, due to problem saving key file.
- Arguments
- arg1 = slot number
- Detailed Description
- Public Key (PK) SSH Authentication key file upload did not complete successfully because Chassis Management Controller is unable to access the configuration database.
- Recommended Response Action
- Retry the operation. If the issue persists, contact your service provider.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8536
- Message
- Unable to add key for slot arg1 of service account, due to corrupt key.
- Arguments
- arg1 = slot number
- Detailed Description
- The add key operation did not complete successfully for the slot identified in the message due to the key being invalid or corrupt.
- Recommended Response Action
- Retry the operation. If the issue persists, contact your service provider.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8537
- Message
- Unable to add key for slot arg1 of service account, due to the key being too long.
- Arguments
- arg1 = slot number
- Detailed Description
- The add key operation did not complete successfully for the slot identified in the message due to the key being too long.
- Recommended Response Action
- Retry the operation. If the issue persists, contact your service provider.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8538
- Message
- Unable to delete key for slot arg1 of service account, due to problem saving key file.
- Arguments
- arg1 = slot number
- Detailed Description
- The Public Key (PK) SSH Authentication key file delete operation did not complete successfully because the Chassis Management Controller is unable to access the configuration database.
- Recommended Response Action
- Retry the operation. If the issue persists, contact your service provider.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8539
- Message
- The key delete operation successfully completed for slot arg1 of service account.
- Arguments
- arg1 = slot number
- Detailed Description
- The Public Key (PK) SSH Authentication key file delete operation is successfully completed for the slot identified in the message.
- Recommended Response Action
- No response action required.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8540
- Message
- The add key operation successfully completed for slot arg1 of service account.
- Arguments
- arg1 = slot number
- Detailed Description
- The Public Key (PK) SSH Authentication key file is successfully uploaded to the Chassis Management Controller.
- Recommended Response Action
- No response action required.
- Category
- Audit (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8600
- Message
- The selected profile was not applied to arg1 .
- Arguments
- arg1 = server list
- Detailed Description
- The profile version must be compatible with the server generation and Lifecycle Controller firmware version.
- Recommended Response Action
- Make sure that profile versions are compatible with target servers when attempting application of profiles to servers.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8601
- Message
- Quick Deploy Profile unable to apply profile arg1 to server arg2
- Arguments
- arg1 = profile name, arg2 = server number
- Detailed Description
- The source profile is not correct in form or content.
- Recommended Response Action
- Recreate source profile or choose a different one.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8602
- Message
- Quick Deploy Profile for server arg1 was not successful.
- Arguments
- arg1 = server number
- Detailed Description
- The system is busy with other operations. The feature was unable to get mutex.
- Recommended Response Action
- Retry the operation. If the issue persists, make sure any other operations have completed and then retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8603
- Message
- Unable to apply profile to server arg1 using Quick Deploy feature, because the CSIOR feature on Server arg2 is disabled.
- Arguments
- arg1 = slot number, arg2 = slot number
- Detailed Description
- The selected profile cannot be applied to the server identified in the message, because the Collect System Inventory On Restart (CSIOR) feature on the server is disabled.
- Recommended Response Action
- Make sure that CSIOR on the server identified in the messages is enabled and retry the operation. For 11th generation servers, to enable CSIOR, restart the server, and select the Ctrl-E setup. Select System Services, and enable CSIOR. For 12th generation servers, to enable CSIOR using Lifecycle Controller GUI, restart the server, click <F2> when the companys logo is displayed. On the iDRAC Settings page, click Lifecycle Controller, and enable CSIOR.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8604
- Message
- Quick Deploy Profile: Server arg1 does not support configuration using profiles.
- Arguments
- arg1 = server number
- Detailed Description
- The target server identified in the message does not support server configuration using profiles.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8605
- Message
- Quick Deploy Profile: Server arg1 generation information is not recognized.
- Arguments
- arg1 = server number
- Detailed Description
- Information about the server identified in the message is not recognized.
- Recommended Response Action
- Restart the Chassis Management Controller (CMC) and retry the operation. The CMC can be restarted by using the Web UI interface and selecting Chassis Overview > Troubleshooting > Reset Components and then select the Reset/Failover CMC button. If the issue persists, contact your service provider.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8606
- Message
- Quick Deploy Profile: Timeout exceeded while waiting for remote services ready on Server arg1 .
- Arguments
- arg1 = server number
- Detailed Description
- The server identified in the message never reported that remote services were ready.
- Recommended Response Action
- Make sure that the iDRAC on the server identified in the message is operating properly and that Lifecycle Controller is enabled, then retry the operation. If the issue persists, perform a virtual reseat of the server and retry the operation. The server can be virtually reseated by using the CMC Web UI interface and selecting Chassis Overview > Troubleshooting > Reset Components and then select Virtual Reseat from the drop down operation for the server identified in the message.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8607
- Message
- Quick Deploy Profile: Starting to apply profile arg1 to server arg2 .
- Arguments
- arg1 = profile name, arg2 = server number
- Detailed Description
- The Quick Deploy of Profile process has started for the server identified in the message.
- Recommended Response Action
- No response action is required
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8608
- Message
- Server Profiles: unable to access server: arg1 for operation [ arg2 ] because of one or more of the following reasons: 1) iDRAC is not ready. 2) Lifecycle Controller of the server is disabled.
- Arguments
- arg1 = slot number, arg2 = wsman operation
- Detailed Description
- The CMC was unable to perform the operation described in the message because of one or more of the following reasons: 1) iDRAC is not ready. 2) Lifecycle Controller of the server is disabled.
- Recommended Response Action
- Make sure that iDRAC on the server identified in the message is operating and that Lifecycle Controller is enabled, and then retry the operation. If the issue persists, perform a virtual reseat of the server and retry the operation. To perform a virtual reseat of the server, on CMC Web interface, select Chassis Overview -> Troubleshooting -> Reset Components. On the Reset Components page, select Virtual Reseat from the drop-down menu for the server identified in the message.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8609
- Message
- Server Profiles: unknown response received from server: arg1 for operation [ arg2 ] because of one or more of the following reasons: 1) iDRAC is not ready. 2) Lifecycle Controller of the server is disabled.
- Arguments
- arg1 = slot number, arg2 = wsman_operation
- Detailed Description
- The CMC was unable to perform the operation described in the message because of one or more of the following reasons: 1) iDRAC is not ready. 2) Lifecycle Controller of the server is disabled.
- Recommended Response Action
- Make sure that iDRAC on the server identified in the message is operating and that Lifecycle Controller is enabled, and then retry the operation. If the issue persists, perform a virtual reseat of the server and retry the operation. To perform a virtual reseat of the server, on CMC Web interface, select Chassis Overview -> Troubleshooting -> Reset Components. On the Reset Components page, select Virtual Reseat from the drop-down menu for the server identified in the message.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8610
- Message
- Job ID: arg1 . CMC sent all settings of profile arg2 to Server (Service Tag: arg3 ) in Slot arg4 .
- Arguments
- arg1 = job ID, arg2 = profile name, arg3 = service tag, arg4 = slot number
- Detailed Description
- All settings of the selected profile were sent to the server identified in the message and the operation is captured in the job identified in the message.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 3 (Informational)
SWC8611
- Message
- Profile " arg1 " and Server (Service Tag: arg2 in Slot arg3 ) are not compatible.
- Arguments
- arg1 = profile name, arg2 = service tag, arg3 = slot number
- Detailed Description
- CMC cannont perform the server profile application because the selected profile version and the server identified in the message are not compatible.
- Recommended Response Action
- Make sure to select the correct version of the profile and/or server, and then retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8612
- Message
- Unable to fully extract boot device information from profile: arg1 .
- Arguments
- arg1 = profile name
- Detailed Description
- The profile identified in the message does not contain boot device information in a usable format.
- Recommended Response Action
- Recreate the profile identified in the message or use a different profile.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8613
- Message
- Unable to fully extract arg1 boot list settings from the profile.
- Arguments
- arg1 = boot list name
- Detailed Description
- The selected profile does not contain setting information for the boot list identified in the message in a usable format.
- Recommended Response Action
- Recreate the profile or use a different profile.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8614
- Message
- Legacy profile setting: arg1 is not recognized.
- Arguments
- arg1 = attribute name
- Detailed Description
- The setting identified in the message is not recognized because the profile is not in a usable format or contains settings that are no longer supported.
- Recommended Response Action
- Recreate the profile or use a different profile.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8616
- Message
- Server in slot arg1 is not ready to be accessed remotely because of one or more of the following reasons: 1) iDRAC is not ready. 2) Lifecycle Controller for of the server is disabled.
- Arguments
- arg1 = slot number
- Detailed Description
- The server identified in the message cannot be accessed remotely by iDRAC because of one or more of the following reasons: 1) iDRAC is not ready. 2) Lifecycle Controller for of the server is disabled.
- Recommended Response Action
- Make sure that the iDRAC on the server identified in the message is operating properly and that Lifecycle Controller is enabled, and then retry the operation. If the issue persists, perform a virtual reseat of the server and retry the operation. The server can be virtually reseated by using the CMC Web GUI interface and selecting Chassis Overview > Troubleshooting > Reset Components and then selecting Virtual Reseat from the drop down menu.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8617
- Message
- Server Profiles: request arg1 for server in slot arg2 was unsuccessful. Returned fault: arg3 .
- Arguments
- arg1 = wsman method, arg2 = slot number, arg3 = wsman fault
- Detailed Description
- The request by the WS-Man method identified in the message for the server in slot identified slot is unsuccessful.
- Recommended Response Action
- Make sure that iDRAC is ready and system is functioning properly. Run the RACADM command "racadm getversion" to list all the servers and make sure the iDRAC version is displayed. If the iDRAC is listed as Not Ready then wait until iDRAC is ready for use. A Virtual Reseat may be required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC8618
- Message
- Server Profiles: request arg1 for server in slot arg2 was unsuccessful. Message ID arg3 . Returned fault: arg4 .
- Arguments
- arg1 = wsman method, arg2 = slot number, arg3 = message id, arg4 = wsman fault
- Detailed Description
- The request for the WS-Man method identified in the message for server in slot identified slot is unsuccessful.
- Recommended Response Action
- Make sure that iDRAC is ready and system is functioning correctly. run the RACADM command at the command line interface (CLI), "racadm getversion" to list all the servers and make sure that the iDRAC version is displayed. If the iDRAC is listed as Not Ready then wait until it becomes ready. A Virtual Reseat may be required.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
SWC8619
- Message
- The Chassis Management Controller is unable to process data from the server in slot arg1 .
- Arguments
- arg1 = slot id
- Detailed Description
- The Chassis Management Controller (CMC) is unable to process inventory data from the server in the slot identified in the message. This can happen if: 1) There is a communications issue between the CMC and the iDRAC on the server identified in the message. 2) Incorrect firmware is installed on network cards. 3) Incorrect firmware is installed on the server iDRAC. 4) There is no free temporary storage in the CMC.
- Recommended Response Action
- Do the following and retry the operation: 1) Make sure the latest firmware is installed on the network cards and iDRAC on the server identified in the message. 2) Reset the Chassis Management Controller. 3) Reset the server iDRAC. If the issue persists, contact your service provider.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8620
- Message
- The Chassis Management Controller is unable to communicate with the iDRAC in server slot arg1 .
- Arguments
- arg1 = slot id
- Detailed Description
- The Chassis Management Controller is unable to communicate with the iDRAC in server slot identified in the message.
- Recommended Response Action
- Reset the server iDRAC. If the issue persists, contact your service provider.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8621
- Message
- The Chassis Management Controller is unable to process inventory data from the server in slot arg1 .
- Arguments
- arg1 = slot id
- Detailed Description
- The Chassis Management Controller (CMC) is unable to process inventory data from the server slot identified in the message. This can happen if there is no free temporary storage in CMC.
- Recommended Response Action
- Restart the Chassis Management Controller (CMC). To restart the CMC, start an SSH session to the CMC and enter the command "racadm racreset". Wait for the CMC to finsh restarting and check if the inventory data is collected. If the issue persists, contact your service provider.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8622
- Message
- Quick Deploy Profile: Unable to access remote network share and apply assigned profile to the server in slot arg1 .
- Arguments
- arg1 = slot number
- Detailed Description
- The remote network share settings are accessible on the CMC web interface at Server Overview/Setup/Remote Network Share tab. These settings must be correct for the CMC to connect to the remote network share and perform the application of the profile as specified in the Quick Deploy tab on the Profiles page.
- Recommended Response Action
- Make sure that the remote network share settings in the CMC are correct and that the remote share NFS/CIFS server is functioning correctly. Use the "Test Network" button in the CMC Web interface to make sure that the CMC can access the remote share.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
SWC8623
- Message
- Unable to save the I/O Aggregator configuration in arg1 .
- Arguments
- arg1 = slot id
- Detailed Description
- The current configuration details of IOA in the slot identified in the message could not be saved to its startup configuration.
- Recommended Response Action
- Power-cycle the IOA and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 2 (Warning)
- Trap/EventID
- 10530
SWC8624
- Message
- The network communication session between CMC and I/O Aggregator cannot be started on arg1 .
- Arguments
- arg1 = slot id
- Detailed Description
- The network communication session between CMC and I/O Aggregator (IOA) cannot be started because the IOA did not respond.
- Recommended Response Action
- Power-cycle the IOA and retry the operation.
- Category
- Configuration (SWC = Software Config)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 10529
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\