- Notes, Cautions, and Warnings
- Introduction
- AMP Event Messages
- ASR Event Messages
- BAR Event Messages
- BAT Event Messages
- BIOS Event Messages
- BOOT Event Messages
- CBL Event Messages
- CMC Event Messages
- CPU Event Messages
- CPUA Event Messages
- CTL Event Messages
- DH Event Messages
- DIAG Event Messages
- DIS Event Messages
- DKM Event Messages
- ECM Event Messages
- ENC Event Messages
- EPP Event Messages
- FAN Event Messages
- FC Event Messages
- FCD Event Messages
- FLDC Event Messages
- FSD Event Messages
- HWC Event Messages
- IOID Event Messages
- IOV Event Messages
- IPA Event Messages
- ISM Event Messages
- JCP Event Messages
- LC Event Messages
- LIC Event Messages
- LNK Event Messages
- LOG Event Messages
- MEM Event Messages
- NIC Event Messages
- OSD Event Messages
- OSE Event Messages
- PCI Event Messages
- PDR Event Messages
- PFM Event Messages
- POW Event Messages
- PR Event Messages
- PST Event Messages
- PSU Event Messages
- PSUA Event Messages
- PWR Event Messages
- RAC Event Messages
- RDU Event Messages
- RED Event Messages
- RFL Event Messages
- RFLA Event Messages
- RFM Event Messages
- RRDU Event Messages
- RSI Event Messages
- SEC Event Messages
- SEL Event Messages
- SSD Event Messages
- STOR Event Messages
- SUP Event Messages
- SWC Event Messages
- SWU Event Messages
- SYS Event Messages
- TMP Event Messages
- TMPS Event Messages
- TST Event Messages
- UEFI Event Messages
- USR Event Messages
- VDR Event Messages
- VF Event Messages
- VFL Event Messages
- VFLA Event Messages
- VLT Event Messages
- VME Event Messages
- VRM Event Messages
Event and Error Message Reference Guide for 13th Generation Dell PowerEdge ServersVersion 1.2
PCI Event Messages
PCI1300
- Message
- A front panel diagnostic interrupt was detected.
- Detailed Description
- The front panel diagnostic was pressed, and the system may be halted as a result. The interrupt was user induced.
- Recommended Response Action
- Reset the system to continue operation.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
PCI1302
- Message
- A bus time-out was detected on a component at bus arg1 device arg2 function arg3 .
- Arguments
- arg1 = bus, arg2 = device, arg3 = func
- Detailed Description
- System performance may be degraded. The device has failed to respond to a transaction (master/target abort or completion timeout).
- Recommended Response Action
- Cycle input power, update component drivers, if device is removable, re-install the device.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
PCI1304
- Message
- An I/O channel check error was detected.
- Detailed Description
- None
- Recommended Response Action
- Cycle input power, update component drivers, if device is removable, re-install the device.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
- LCD Message
- I/O channel check error detected. Power cycle system.
PCI1306
- Message
- A software error was detected on a component at bus arg1 device arg2 function arg3 .
- Arguments
- arg1 = bus, arg2 = device, arg3 = func
- Detailed Description
- None
- Recommended Response Action
- Reboot the system and update the component drivers.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
PCI1308
- Message
- A PCI parity error was detected on a component at bus arg1 device arg2 function arg3 .
- Arguments
- arg1 = bus, arg2 = device, arg3 = func
- Detailed Description
- System performance may be degraded, or system may fail to operate.
- Recommended Response Action
- Cycle input power, update component drivers, if device is removable, re-install the device.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
- LCD Message
- PCI parity error on bus <bus> device <device> function <func>. Power cycle system.
PCI1310
- Message
- A PCI system error was detected on a component at bus arg1 device arg2 function arg3 .
- Arguments
- arg1 = bus, arg2 = device, arg3 = func
- Detailed Description
- System performance may be degraded, or system may fail to operate.
- Recommended Response Action
- Cycle input power, update component drivers, if device is removable, re-install the device.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
- LCD Message
- PCI system error on bus <bus> device <device> function <func>. Power cycle system.
PCI1314
- Message
- A bus correctable error was detected on a component at bus arg1 device arg2 function arg3 .
- Arguments
- arg1 = bus, arg2 = device, arg3 = func
- Detailed Description
- System performance may be degraded.
- Recommended Response Action
- Cycle input power, update component drivers, if device is removable re-install the device at the next scheduled service time.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
PCI1316
- Message
- A bus uncorrectable error was detected on a component at bus arg1 device arg2 function arg3 .
- Arguments
- arg1 = bus, arg2 = device, arg3 = func
- Detailed Description
- System performance may be degraded, or system may fail to operate.
- Recommended Response Action
- Cycle input power, update component drivers, if device is removable, re-install the device.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
PCI1318
- Message
- A fatal error was detected on a component at bus arg1 device arg2 function arg3 .
- Arguments
- arg1 = bus, arg2 = device, arg3 = func
- Detailed Description
- System performance may be degraded, or system may fail to operate.
- Recommended Response Action
- Cycle input power, update component drivers, if device is removable, re-install the device.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
- LCD Message
- Fatal error on bus <bus> device <device> function <func>. Power cycle system.
PCI1319
- Message
- A high-severity issue is detected in the SSD bay arg1 , Slot arg2 .
- Arguments
- arg1 = bay id, arg2 = slot id
- Detailed Description
- A high-severity issue was detected in the SSD bay identified in the message.
- Recommended Response Action
- Remove and reinsert the component identified in the message, and then monitor the log for a re-occurrance of the issue. If the issue persists, and occurs during server startup, update the component firmware. If the issue persists and occurs during OS runtime, restart the server and update the OS drivers for the component identified in the message.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
PCI1320
- Message
- A bus fatal error was detected on a component at bus arg1 device arg2 function arg3 .
- Arguments
- arg1 = bus, arg2 = device, arg3 = func
- Detailed Description
- System performance may be degraded, or system may fail to operate.
- Recommended Response Action
- Cycle input power, update component drivers, if device is removable, re-install the device.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
- LCD Message
- Bus fatal error on bus <bus> device <device> function <func>. Power cycle system.
PCI1321
- Message
- A high-severity issue is detected in a component of the bus arg1 , device 0, function arg2 .
- Arguments
- arg1 = bus ID, arg2 = function ID
- Detailed Description
- A high-severity issue is detected in the component identified in the message.
- Recommended Response Action
- Remove and reinsert the component identified in the message, and then monitor the log for a re-occurrance of the issue. If the issue persists, and occurs during server startup, update the component firmware. If the issue persists and occurs during OS runtime, restart the server and update the OS drivers for the component identified in the message.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
PCI1322
- Message
- Bus performance degraded for a component at bus arg1 device arg2 function arg3 .
- Arguments
- arg1 = bus, arg2 = device, arg3 = func
- Detailed Description
- System performance may be degraded. The bus is not operating at maximum speed or width.
- Recommended Response Action
- Cycle input power, update component drivers, if device is removable, re-install the device.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 2 (Warning)
- Trap/EventID
- 2418
PCI1342
- Message
- A bus time-out was detected on a component at slot arg1 .
- Arguments
- arg1 = number
- Detailed Description
- System performance may be degraded. The device has failed to respond to a transaction (master/target abort or completion timeout).
- Recommended Response Action
- Cycle input power, update component drivers, if device is removable, re-install the device.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
PCI1344
- Message
- An I/O channel check error was detected.
- Detailed Description
- None
- Recommended Response Action
- Cycle input power, update component drivers, if device is removable, re-install the device.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
- LCD Message
- An I/O channel check error detected. Power cycle system.
PCI1346
PCI1348
- Message
- A PCI parity error was detected on a component at slot arg1 .
- Arguments
- arg1 = number
- Detailed Description
- System performance may be degraded, or system may fail to operate.
- Recommended Response Action
- Cycle input power, update component drivers, if device is removable, re-install the device.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
- LCD Message
- PCI parity error on slot <number>. Reseat PCI card
PCI1350
- Message
- A PCI system error was detected on a component at slot arg1 .
- Arguments
- arg1 = number
- Detailed Description
- System performance may be degraded, or system may fail to operate.
- Recommended Response Action
- Cycle input power, update component drivers, if device is removable, re-install the device.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
- LCD Message
- PCI system error on slot <number>. Reseat PCI card
PCI1354
- Message
- A bus correctable error was detected on a component at slot arg1 .
- Arguments
- arg1 = number
- Detailed Description
- System performance may be degraded.
- Recommended Response Action
- Cycle input power, update component drivers, remove and re-install the device at the next scheduled service time.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
PCI1356
- Message
- A bus uncorrectable error was detected on a component at slot arg1 .
- Arguments
- arg1 = number
- Detailed Description
- System performance may be degraded, or system may fail to operate.
- Recommended Response Action
- Cycle input power, update component drivers, if device is removable, re-install the device.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
PCI1358
- Message
- A fatal error was detected on a component at slot arg1 .
- Arguments
- arg1 = number
- Detailed Description
- System performance may be degraded, or system may fail to operate.
- Recommended Response Action
- Cycle input power, update component drivers, if device is removable, re-install the device.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
- LCD Message
- Fatal error on slot <number>. Reseat PCI card
PCI1360
- Message
- A bus fatal error was detected on a component at slot arg1 .
- Arguments
- arg1 = number
- Detailed Description
- System performance may be degraded, or system may fail to operate.
- Recommended Response Action
- Cycle input power, update component drivers, if device is removable, re-install the device.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
- LCD Message
- Bus fatal error on slot <number>. Reseat PCI card
PCI1362
- Message
- Bus performance degraded for a component at slot arg1 .
- Arguments
- arg1 = number
- Detailed Description
- System performance may be degraded. The bus is not operating at maximum speed or width.
- Recommended Response Action
- Cycle input power, update component drivers, remove and re-install the device at the next scheduled service time.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 2 (Warning)
- Trap/EventID
- 2418
PCI2000
- Message
- A fatal IO error detected on a component at bus arg1 device arg2 function arg3 .
- Arguments
- arg1 = bus, arg2 = device, arg3 = func
- Detailed Description
- System performance may be degraded, or system may fail to operate.
- Recommended Response Action
- Cycle input power, update component drivers, remove and re-install the device.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
- LCD Message
- Fatal IO error on bus <bus> device <device> function <func>. Contact support
PCI2001
- Message
- The component at bus arg1 device arg2 function arg3 recovered from a fatal IO error.
- Arguments
- arg1 = bus, arg2 = device, arg3 = func
- Detailed Description
- None
- Recommended Response Action
- No response action is required.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 3 (Informational)
- Trap/EventID
- 2419
PCI2002
- Message
- A fatal IO error detected on a component at slot arg1 .
- Arguments
- arg1 = number
- Detailed Description
- System performance may be degraded, or system may fail to operate.
- Recommended Response Action
- Cycle input power, update component drivers, remove and re-install the device.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
- LCD Message
- Fatal IO error on slot <number>. Contact support
PCI2003
PCI3000
- Message
- Device option ROM on embedded NIC failed to support Link Tuning or FlexAddress.
- Detailed Description
- Either the BIOS, BMC/iDRAC, or LOM firmware is out of date and does not support FlexAddress.
- Recommended Response Action
- Update BIOS, BMC/iDRAC, and LOM firmware. If problem persists please contact customer support.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
PCI3001
PCI3002
- Message
- Failed to program virtual MAC address on a component at bus arg1 device arg2 function arg3 .
- Arguments
- arg1 = bus, arg2 = device, arg3 = func
- Detailed Description
- Either the BIOS, BMC/iDRAC, LOM, or NIC firmware is out of date and does not support FlexAddress.
- Recommended Response Action
- Update BIOS, BMC/iDRAC, LOM, and mezzanine card firmware. If problem persists please contact customer support.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
PCI3003
- Message
- Virtual MAC address for component at bus arg1 device arg2 function arg3 was successfully programed.
- Arguments
- arg1 = bus, arg2 = device, arg3 = func
- Detailed Description
- None
- Recommended Response Action
- No response action is required.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 3 (Informational)
- Trap/EventID
- 2419
PCI3004
- Message
- Device option ROM on mezzanine card arg1 failed to support Link Tuning or FlexAddress.
- Arguments
- arg1 = number
- Detailed Description
- Either the BIOS, BMC/iDRAC, or mezzanine card firmware is out of date and does not support FlexAddress.
- Recommended Response Action
- Update BIOS, BMC/iDRAC, and mezzanine card firmware. If problem persists please contact customer support.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
PCI3005
PCI3006
- Message
- Failed to get Link Tuning or FlexAddress data from iDRAC.
- Detailed Description
- Either the BIOS or BMC/iDRAC firmware is out of date and does not support FlexAddress.
- Recommended Response Action
- Update BIOS, and BMC/iDRAC firmware. If problem persists please contact customer support.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
PCI3007
PCI3008
- Message
- A non-fatal PCIe error detected on a component at bus arg1 device arg2 function arg3 .
- Arguments
- arg1 = bus, arg2 = device, arg3 = func
- Detailed Description
- System performance may be degraded.
- Recommended Response Action
- Cycle input power, update component drivers, remove and re-install the device at the next service window.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 2 (Warning)
- Trap/EventID
- 2418
PCI3009
- Message
- PCIe is operating normally on a component at bus arg1 device arg2 function arg3 .
- Arguments
- arg1 = bus, arg2 = device, arg3 = func
- Detailed Description
- None
- Recommended Response Action
- No response action is required.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 3 (Informational)
- Trap/EventID
- 2419
PCI3010
- Message
- A non-fatal IO error detected on a component at bus arg1 device arg2 function arg3 .
- Arguments
- arg1 = bus, arg2 = device, arg3 = func
- Detailed Description
- System performance may be degraded.
- Recommended Response Action
- Cycle input power, update component drivers, remove and re-install the device at the next service window.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 2 (Warning)
- Trap/EventID
- 2418
PCI3011
- Message
- The component at bus arg1 device arg2 function arg3 recovered from a non-fatal IO error.
- Arguments
- arg1 = bus, arg2 = device, arg3 = func
- Detailed Description
- None
- Recommended Response Action
- No response action is required.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 3 (Informational)
- Trap/EventID
- 2419
PCI3012
- Message
- The QuickPath Interconnect (QPI) width degraded.
- Detailed Description
- System performance may be degraded. The bus is not operating at maximum speed or width.
- Recommended Response Action
- Reset the system, if the problem persists reinstall processors.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 2 (Warning)
- Trap/EventID
- 2418
PCI3013
PCI3014
- Message
- A non-fatal PCIe error detected on a component at slot arg1 .
- Arguments
- arg1 = number
- Detailed Description
- System performance may be degraded.
- Recommended Response Action
- Cycle input power, update component drivers, remove and re-install the device at the next scheduled service time.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 2 (Warning)
- Trap/EventID
- 2418
PCI3015
PCI3016
- Message
- Device option ROM on mezzanine card failed to support Link Tuning or FlexAddress.
- Detailed Description
- Either the BIOS, BMC/iDRAC, or mezzanine card firmware is out of date and does not support FlexAddress.
- Recommended Response Action
- Update BIOS, BMC/iDRAC, and mezzanine card firmware. If problem persists please contact customer support.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
PCI3017
PCI3018
- Message
- New PCI card(s) have been detected in the system. Fan speeds may have changed to add additional cooling to the cards.
- Detailed Description
- New PCI card(s) have been detected in the system that may require additional airflow. Fan speeds may have changed to add additional cooling to the cards.
- Recommended Response Action
- Changing default fan response to PCIe cards should be done with appropriate understanding of the PCIe cooling needs of the cards present in the system. If the automatic cooling response is insufficient, additional cooling can be added by one of the following methods. 1) From iDRAC Web GUI, click Hardware -> Fans -> Setup, then from the fan speed offset drop-down list appropriately select the cooling level needed or set the minimum fan speed to a custom value. 2) From F2 System Setup, select iDRAC Settings -> Thermal, and set a higher fan speed from the fan speed offset or minimum fan speed. 3) For RACADM commands run "racadm help system.thermalsettings". If a lower fan speed is required, contact your service provider for the appropriate IPMI commands to reduce the default fan speed response for new PCIe cards.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 3 (Informational)
- Trap/EventID
- 2419
PCI3019
- Message
- A low-severity issue is detected in the SSD bay arg1 , Slot arg2 .
- Arguments
- arg1 = bay id, arg2 = slot id
- Detailed Description
- A low-severity issue was detected in the SSD bay identified in the message.
- Recommended Response Action
- Remove and reinsert the component identified in the message, and then monitor the log for a re-occurrance of the issue. If the issue persists, and occurs during server startup, update the component firmware. If the issue persists and occurs during OS runtime, restart the server and update the OS drivers for the component identified in the message..
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 2 (Warning)
- Trap/EventID
- 2419
PCI3020
- Message
- A low-severity issue is detected in a component of the bus arg1 , device 0, function arg2 .
- Arguments
- arg1 = bus ID, arg2 = function ID
- Detailed Description
- A low-severity issue is detected in the component identified in the message.
- Recommended Response Action
- Remove and reinsert the component identified in the message, and then monitor the log for a re-occurrance of the issue. If the issue persists, and occurs during server startup, update the component firmware. If the issue persists and occurs during OS runtime, restart the server and update the OS drivers for the component identified in the message.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 2 (Warning)
PCI5001
- Message
- A PCIe card carrier containing a PCIe card is inserted in PCIe slot arg1 .
- Arguments
- arg1 = slot number
- Detailed Description
- A PCIe card carrier containing a PCIe card is present in the slot identified in the message. This PCIe card will be enabled when the associated server is turned on or power cycled.
- Recommended Response Action
- Turn on or power cycle the associated server to enable the PCIe card.
- Category
- Configuration (PCI = PCI Device)
- Severity
- Severity 3 (Informational)
- Trap/EventID
- 10611
PCI5002
- Message
- A PCIe card carrier that does not contain a PCIe card is inserted in the PCIe slot arg1 .
- Arguments
- arg1 = slot number
- Detailed Description
- A PCIe card carrier that does not contain a PCIe card is inserted in the PCIe slot identified in the message.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (PCI = PCI Device)
- Severity
- Severity 3 (Informational)
- Trap/EventID
- 10611
PCI5003
- Message
- A PCIe card carrier is removed from the PCIe slot arg1 .
- Arguments
- arg1 = slot number
- Detailed Description
- A PCIe card carrier is removed from the PCIe slot identified in the message.
- Recommended Response Action
- No response action is required.
- Category
- Configuration (PCI = PCI Device)
- Severity
- Severity 3 (Informational)
- Trap/EventID
- 10611
PCI5004
- Message
- A power fault issue is detected in the PCIe adapter that was turned on in PCIe slot arg1 .
- Arguments
- arg1 = slot number
- Detailed Description
- The Chassis Management Controller (CMC) detected an issue in the PCIe adapter that was turned on in the slot identified in the message.
- Recommended Response Action
- Make sure that: 1) The PCIe adapter used is supported by the Chassis Management Controller (CMC). For a list of supported adapters, contact your service provider. 2) The adapter is not damaged. 3) The power requirement of adapter is not more than the power allocated to the slot. 4) The adapter is properly inserted in the slot.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
PCI5005
- Message
- An auxiliary power fault issue is detected in the PCIe adapter that was turned on in PCIe slot arg1 .
- Arguments
- arg1 = slot number
- Detailed Description
- Chassis Management Controller (CMC) detected an issue in the PCIe adapter that was turned on in the slot identified in the message.
- Recommended Response Action
- Make sure that: 1) The PCIe adapter used is supported by the Chassis Management Controller (CMC). For a list of supported adapters, contact your service provider. 2) The adapter is not damaged. 3) The adapter is properly inserted in the slot.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
PCI5006
- Message
- The power-related issue of the PCIe adapter in slot arg1 is resolved.
- Arguments
- arg1 = slot number
- Detailed Description
- The power related issue of the PCIe device in the slot identified in the message is resolved.
- Recommended Response Action
- No response action is required.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 3 (Informational)
- Trap/EventID
- 2419
PCI5007
- Message
- The auxiliary power-related issue of the PCIe adapter in slot arg1 is resolved.
- Arguments
- arg1 = slot number
- Detailed Description
- The 3.3 Volt Regulator power related issue of PCIe carrier present in the slot identified in the message is resolved.
- Recommended Response Action
- No response action is required.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 3 (Informational)
- Trap/EventID
- 2419
PCI5008
- Message
- The Chassis Management Controller (CMC) is unable to communicate with the PCIe switch board.
- Detailed Description
- The Chassis Management Controller (CMC) could not successfully connect to the PCIe switch board.
- Recommended Response Action
- Do the following: 1) Perform an AC Power Cycle operation on the Chassis by disconnecting the chassis from AC power, waiting for 30 seconds, and then reconnecting AC power. 2) Power on at least one server. Using the Chassis Management Controller (CMC) web interface, select Server Overview->Power->Control and then click the Operation field and select the Power On Server operation. If the issue persists, contact your service provider.
- Category
- System Health (PCI = PCI Device)
- Severity
- Severity 1 (Critical)
- Trap/EventID
- 2417
PCI5009
- Message
- The PCIe adapter in the PCIe slot arg1 was removed from the slot while the server arg2 was turned-on.
- Arguments
- arg1 = PCIe slot number, arg2 = server slot number
- Detailed Description
- Chassis Management Controller (CMC) detected that a PCIe adapter was removed from a server which was turned-on. This may cause the server operating system to stop responding or to function in an improper manner.
- Recommended Response Action
- Perform a Power Cycle operation on the associated server. Restarting the operating system will not resolve this issue. Only remove PCIe adapters when the associated server is turned-off.
- Category
- Audit (PCI = PCI Device)
- Severity
- Severity 2 (Warning)
- Trap/EventID
- 8562
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\