Dell OpenManage Deployment Toolkit Version 5.4 Command Line Interface Reference Guide

PDF

lancfgparams

Table 1. lancfgparamsThe following table describes the option, sub-option, valid arguments and descriptions for the lancfgparams.
Option	Sub-option	Valid Arguments	Description
lancfgparams or lcp			Configures and displays LAN configuration parameters. This option can be replicated.
	--ipaddrsrc	static, dhcp	Sets the IP address source for the LAN channel. This sub-option can be replicated.
	--ipaddress	<ipaddress>	Sets the IP address for the LAN channel. This sub-option cannot be replicated.
	--subnetmask	<subnetmask>	Sets the subnet mask for the LAN channel. This sub-option can be replicated.
	--gateway	<gateway>	Sets the gateway for the LAN channel. This sub-option can be replicated.
	--commstring	<string>	Sets the community string (maximum of 16 printable ASCII characters) used in a platform event trap (PET). This sub-option can be replicated.
	--destipaddr	<ipaddress>	Sets the destination IP address or Fully Qualified Domain Name (FQDN) for the alert destination specified with the alertdest sub-option. The destipaddr sub-option is dependent on the alertdest sub-option. If the alertdest sub-option is not specified on the command line, the first alert destination (alertdest=1) is set with this IP address or FQDN. This sub-option can be replicated. NOTE FQDN is applicable only for destipaddr option and is supported only on PowerEdge 12G systems. Example 1 (to set the destination IP address): A:>syscfg lcp --alertdest=1 --destipaddr=192.168.100.15 Example 2 (to set the destination IP address as FQDN): A:>syscfg lcp --alertdest=1 --destipaddr=xxx.yyy.com
	--alertdest	1, 2, 3, 4	Sets the destination for the LAN alert. This sub-option can be replicated.
	--vlantag	enable, disable	Enables or disables VLAN tagging. This sub-option can be replicated.
	--vlanid	<string>	Sets the 12-bit VLAN ID. This sub-option can be replicated.
	--vlanpriority	0–7	Sets the VLAN priority value. This sub-option can be replicated.
	--macaddress	NA	Displays the BMC MAC address. This sub-option cannot be replicated.
	--nicselection NOTE This option is available only with the appropriate installed license.	shared, sharedfailover, dedicated, sharedreceiveonall	Sets the operating mode of the NIC to shared, sharedfailover, dedicated, or sharedreceiveonall. Some of these options are not applicable on certain systems. NOTE This option is applicable on systems prior to PowerEdge 12G systems. The sharedreceiveonall argument is available only on PowerEdge 11G systems.
	--nicselection NOTE This option is available only with the appropriate installed license.	dedicated, lom1, lom2, lom3, lom4	Sets the operating mode of the iDRAC7 NIC to dedicated, lom1, lom2, lom3, or lom4. Some of these options are not applicable on certain systems due to underlying hardware. NOTE This option is applicable on PowerEdge 11G systems.
	--nicselectionfailover NOTE This option is available only with the appropriate installed license.	none, lom1, lom2, lom3, lom4, all	Sets the operating mode of the NIC selection failover to none, lom1, lom2, lom3, lom4, or all. Some of these options are not applicable on certain systems. due to underlying hardware. NOTE This option is applicable on PowerEdge 12G systems.
	--fullduplex	enable, disable	Enables or disables full duplex on the RAC network interface.
	--autoneg	enable, disable	Enables or disables autonegotiation.
	--speed	10,100	Sets the network interface speed to 10 or 100 Mbps.
	--dnsdhcp	enable, disable	Enables or disables obtaining the DNS server IP address through DHCP.
	--dnsserver1	<ipaddress>	Sets the IP address of the primary DNS server for domain name resolution.
	--dnsserver2	<ipaddress>	Sets the IP address of the secondary DNS server for domain name resolution.
	--dnsregisterrac	enable, disable	Enables or disables binding of the RAC name to the IP address.
	--dnsracname	<string>	Sets the name of the RAC.
	--domainnamefromdhcp	enable, disable	Enables or disables getting the RAC domain name through DHCP.
	--domainname	<string>	Sets the domain name of the RAC. Example 1 (to display the current LAN configuration settings): A:>syscfg --lancfgparams destipaddr=192.168.100.15 vlantag=enable vlanid=1000 vlanpriority=7 macaddress=0:6:5b:fb:c8:a7 commstring=public ipaddrsrc=static ipaddress=192.168.100.10 subnetmask=255.255.255.0 gateway=192.168.100.1 Example 2 (to set the LAN configuration parameters): A:>syscfg --lancfgparams --destipaddr=192.168.100.15 --vlantag=enable --vlanid=1000 --vlanpriority=7 --macaddress=0:6:5b:fb:c8:a7 --commstring=public --ipaddrsrc=static --ipaddress=192.168.100.10 --subnetmask=255.255.255.0 --gateway=192.168.100.1