0 |
RAIDCFG Command successful! |
1 |
Error! Incorrect Syntax. |
2 |
Failure! |
3 |
Illegal operation |
4 |
Unsupported operation |
5 |
Device not found. |
6 |
Format boot drive illegal |
7 |
Buffer too small. |
8 |
Virtual Disk contains boot partition.
Use force option to delete. |
9 |
Init boot drive failed. |
10 |
Format boot drive failed. |
11 |
Cannot write boot drive. |
12 |
Unsupported RAID value. |
13 |
Invalid RAID configuration. |
14 |
Span depth not in range. |
15 |
RAID 1 failed. |
16 |
Exactly 2 array disks are required to
create a RAID 1 virtual disk. |
17 |
Unsupported stripe size value. |
18 |
RAID 5 only. |
19 |
RAID 5 error. |
20 |
A minimum of 3 array disks are required
to create a RAID 5 virtual disk. |
21 |
RAID 0 failed. |
22 |
RAID 10 failed. |
23 |
RAID 50 failed. |
24 |
RAID 5 not supported. |
25 |
RAID 50 not supported. |
26 |
Size too small for given RAID type. |
27 |
Wrong number of disks for RAID 1- concatenated. |
28 |
Insufficient space to mirror disks. |
29 |
Create Mirror not supported. |
30 |
Disk in use. |
31 |
Disk Lock operation failed. |
32 |
Disk locked. |
33 |
Disk Unlock operation failed. |
34 |
Disk Unlocked. |
35 |
Disk failed on rebuild. |
36 |
Hot Spare not free. |
37 |
Disk Diagnostic failed. |
38 |
Disk Rebuild failed. |
39 |
Disk Format failed. |
40 |
Cancel of Disk Diagnostic failed. |
41 |
Cancel of Disk Rebuild failed. |
42 |
Cancel of Disk Format failed |
43 |
Assign Hot Spare failed |
44 |
Disk too Small for Hot Spare. |
45 |
Unassign Hot Spare failed. |
46 |
Prepare Disk for Removal failed. |
47 |
Disk Online failed. |
48 |
Disk Offline failed. |
49 |
UnMount Operation failed. |
50 |
Mount Operation failed. |
51 |
Cannot Format Array Disk. |
52 |
Bad chunk size. |
53 |
Invalid disk. |
54 |
Virtual disk not found. |
55 |
Virtual disk locked. |
56 |
Drive in use. |
57 |
Reached maximum physical size. |
58 |
Reached maximum count of virtual disks. |
59 |
There is not enough free space on the
array disk(s) to allow the operation to complete; the size of the
virtual disk is too large; or communication to the array disk(s) has
been lost. |
60 |
Select the array disks that are part of
a similar type of virtual disk (T10 protection and encryption capability)
or the array disks that are not part of any virtual disks. |
61 |
Invalid Parameter |
62 |
Failed drive cannot be added. |
63 |
The controller cannot support the number
of array disks that you have selected. Choose a smaller number. |
64 |
Delete virtual disk failed. Controller
busy. |
65 |
Delete virtual disk failed. |
66 |
Create virtual disk failed. |
67 |
Create virtual disk failed. Controller
busy. |
68 |
Create virtual disk failed. Failed to map
virtual disk to operating system disk. |
69 |
Create virtual disk failed. Failed to
map virtual disk to operating system disk. |
70 |
Virtual disk initialization failed. |
71 |
Virtual disk initialization failed. Controller
busy. |
72 |
Virtual disk reconstruction failed. Controller
busy. |
73 |
Virtual disk resynching failed. Controller
busy. |
74 |
Flush Virtual disk's cache failed on controller. |
75 |
Virtual disk partition specified not found. |
76 |
Unsupported cache policy value. |
77 |
Unsupported write policy value. |
78 |
Unsupported read policy value. |
79 |
Cancel initialization on virtual disk failed. |
80 |
Cancel reconstruction on virtual disk
failed. |
81 |
Cancel resynchronization on virtual disk
failed. |
82 |
The maximum number of virtual disks that
can be created has been reached. |
83 |
The new virtual disk must use only the
remaining free space on the array disks used in the last virtual disk
you created. Select all array disks that are used in the last virtual
disk you created. |
84 |
You have selected an array disk that is
in a degraded or failed state. Choose another array disk. |
85 |
Delete the last created virtual disk first. |
86 |
Virtual disk initialized for use and no
override requested. |
87 |
Virtual disk type requested is invalid
for the attempted operation. |
88 |
Virtual disk Move operation failed. Cannot
rename, virtual disk is already in use. |
89 |
Failover invalid. |
90 |
Virtual disk resynching. |
91 |
Virtual disk resynch failed. |
92 |
Virtual disk reconstruct failed. |
93 |
Cannot format a virtual disk that contains
a boot or system partition. |
94 |
Cannot initialize a virtual disk that
contains a boot or system partition. |
95 |
Virtual disk Copy failed. |
96 |
Virtual disk mirror set required. |
97 |
Virtual disk Create - Read-only failed. |
98 |
Virtual disk Create - Read-write failed. |
99 |
Virtual disk - Clear-to-zero failed. |
100 |
Virtual Disk Requires Non Multilevel. |
101 |
Virtual Disk Promote Operation failed. |
102 |
Specified virtual disk has no drive letter
assigned to it. |
103 |
Cannot expose virtual disk. |
104 |
Cannot reconfigure virtual disk. |
105 |
Cannot stop the reconfiguration of the
virtual disk. |
106 |
SMART report count not supported. |
107 |
Operations on hidden virtual disks are
not allowed. |
108 |
Virtual disk is in use. |
109 |
The virtual disk is in use. It cannot
be reconfigured at this time. |
110 |
Virtual disk operation is temporarily unavailable.
Initialization in progress. |
111 |
Virtual disk operation is temporarily
unavailable. Reconstruction in progress. |
112 |
Virtual disk operation is temporarily
unavailable. Rebuild in progress. |
113 |
Virtual disk operation is temporarily
unavailable. Check consistency in progress. |
114 |
Specified virtual disk too small. |
115 |
Virtual disk operation not supported.
Size too small. |
116 |
Operation is temporarily unavailable. Space
in use. |
117 |
Cannot reconfigure to the given RAID level. |
118 |
Cannot reconfigure from current RAID level
to the given RAID level. |
119 |
One of the array disks selected for the
virtual disk is already in use. |
120 |
Virtual disk operation not supported. Cannot
use non-RAID disk. |
121 |
Controller Read Configuration failed. |
122 |
Controller Write Configuration failed. |
123 |
Controller cache flush failed. |
124 |
Enable alarm on controller failed. |
125 |
Disable alarm on controller failed. |
126 |
Quiet alarm on controller failed. |
127 |
Controller failed to perform the task. |
128 |
Specified bus not found for controller. |
129 |
Call to set cache mode on the controller
failed. |
130 |
Unexpected controller error. |
131 |
Controller out of memory. |
132 |
Invalid controller state. |
133 |
Controller failed. |
134 |
Controller busy. |
135 |
Controller does not exist. |
136 |
Controller name is invalid. |
137 |
Controller is iterated. |
138 |
Rename of virtual disk was not successful. |
139 |
The controller was not able to erase the
file system from the specified virtual disk. |
140 |
The controller was not able to add space
to the specified concatenation set. |
141 |
The controller was not able to get the
status of the specified mirror set. |
142 |
The controller was not able to set the
requested failover space. |
143 |
The controller cannot get the failover
space information. |
144 |
Controller cannot unmirror the specified
virtual disk. |
145 |
The controller could not split the specified
virtual disk. |
146 |
The controller could not lock the specified
virtual disk. |
147 |
Controller IO paused. |
148 |
No controller parameter support. |
149 |
Controller does not recognize parameter
symbol. |
150 |
Controller Battery Recondition failed. |
151 |
Controller Get disk signature failed. |
152 |
Controller Read Flags failed. |
153 |
Controller Set Flags failed. |
154 |
Controller Remove Snap Shot failed. |
155 |
Controller not supported. |
156 |
Controller device initialization failure. |
157 |
Partner controller already opened readwrite. |
158 |
No partner controller found. |
159 |
The virtual disk is not valid for requested
operation. |
160 |
Cannot communicate with controller. |
161 |
Set operation failed. |
162 |
Operation to update error count of SMART
device has failed. |
163 |
Operation to clear error count of SMART
device has failed. |
164 |
Driver could not execute. |
165 |
Cannot delete virtual disk. |
166 |
Cannot set temperature probe. Invalid
value entered. |
167 |
Cannot set enclosure tag. Invalid value
entered. |
168 |
Cannot set enclosure alarm. |
169 |
Temperature probe value out of range. |
170 |
Cannot set cache mode. |
172 |
Data will be lost on the secondary disk
and a reboot will be forced. |
173 |
Cluster Services (MSCS) is running. Deleting
a virtual disk that contains a cluster resource can result in unpredictable
errors or system hangs (quorum disk). You should shut down cluster
services before deleting cluster resources. Are you sure you want
to proceed? |
174 |
Cannot perform Create Virtual Disk or
Delete Virtual Disk while the other server in a cluster is online.
Please shut one of the servers down and retry the operation. |
176 |
Invalid array disks or failover drives
selected for reconfigure/create operation. Please make sure that all
array disks and failover drives associated with the virtual disk are
selected. |
177 |
The maximum number of partitions have
already been created on one of the selected array disk(s). Each array
disk can hold portions (partitions) of up to 10 virtual disks. This
virtual disk cannot be created because one or more array disk(s) have
reached the partition limit. |
178 |
The virtual disk is in use. Please close
any applications that use the virtual disk and unmount any file systems
that reside on the virtual disk. |
179 |
The firmware version is not supported.
Please update the firmware from http://support.dell.com. |
180 |
The specified device does not have enough
free space to be used as failover space for the specified virtual
disk. |
181 |
The operation failed. Please rescan the
controller and retry the operation. |
182 |
The operation cannot be performed while
a task is running on the specified virtual disk. |
183 |
The specified virtual disk has no dead
disk segments. |
184 |
The operation cannot be performed at this
time. The firmware can recondition a battery that has a Degraded or
Power Low state. The firmware will not recondition a battery that
is functioning normally or that has a Ready, Failed or Missing state. |
185 |
The version of the controller firmware
installed on your system does not support this operation. |
186 |
There are no disks of the correct type
available to be assigned as a hot spare. |
187 |
There are no disks of sufficient size available
to be assigned as a hot spare. |
188 |
There are no disks of the correct type
and sufficient size available to be assigned as a hot spare. |
189 |
The Create Virtual Disk task was successful
but the operating system may not be aware of the new virtual disk. |
191 |
The import of foreign configurations is
complete. Some configurations could not be imported. |
192 |
Enable alarm command failed. The enclosure
processor is busy or a firmware download is in progress. |
193 |
Disable alarm command failed. The enclosure
processor is busy or a firmware download is in progress. |
194 |
Quiet alarm command failed. The enclosure
processor is busy or a firmware download is in progress. |
195 |
An error occurred while resetting a temperature
probe. |
200 |
No array disks found! |
201 |
Invalid Virtual Disk ID! |
202 |
RAID Type & Size are required to create
a virtual disk. Ensure that the RAID type and the size are correct. |
203 |
Invalid Environment command! |
204 |
File is not writable! |
205 |
Setting Environment Variable Command failed! |
206 |
Filename is not provided! |
207 |
Invalid Strict option! Please provide
a valid number between 1 and 100. |
208 |
Span depth is not needed for this RAID
type. |
209 |
Array disk(s) cannot be part of virtual
disk(s) and also be hotspares. |
210 |
Cannot have silent and logfile switch
with the same command. |
211 |
Invalid array disk(s)! |
212 |
Invalid failover disk(s)! |
213 |
Creation of a virtual disk on this RAID
controller requires the use of the entire disk space of the array
disks. The size or - sz parameter is not needed. |
214 |
Invalid size given! size=max or -sz=max
is not supported for this RAID controller. |
215 |
The value given for envname or -envn is
null or too long. |
216 |
Invalid virtual disk size! |
217 |
The strict option provided failed! Virtual
disk is not created. |
218 |
Unable to determine optimum size for Virtual
disk. Ensure that the array disks are of the same protocol (i.e. SAS,
SATA, SCSI). If there is a mismatch of the array disks then the RAIDCFG
will not be able to determine the optimum size. In addition, also
ensure that there is drive size available for the specified virtual
disk. |
219 |
One or more array disks selected to create
virtual disk or hotspare doesn't have enough disk space. Please make
sure that all the array disks and failover drives selected have enough
free space. |
220 |
The number of array disks provided is
incorrect for the requested RAID Type! RAID 1 requires exactly 2 array
disks, RAID 5 requires at least 3 array disks, RAID 10 requires at
least 4 array disks and RAID 50 requires at least 6 array disks. |
221 |
No free array disks found! |
222 |
No global failover disks found! |
223 |
One or more array disks selected for the
virtual disk has foreign configuration. |
224 |
Error in opening the file. |
225 |
SAS 5/IR, SAS 6/IR, H200 and SW RAID requires
atleast two physical disks to create RAID 0 or RAID 1. |
226 |
No Foreign configuration present in the
controller. |
227 |
The virtual disk cannot be created on the
physical disks you selected. Possible reasons include:unsupported
mix of SAS and SATA protocol type disks, unsupported mix of SSD and
HDD media disks. |
228 |
Unsupported array disks selected for VD
creation. |
229 |
Setting stripe size is not supported in
this controller. |
230 |
Invalid VirtualDisk(VD) name specified.
VD name can have alphanumeric characters [A-Z,a-z,0-9,_,-] only. Also,
VD name size must be less than or equal to 15 characters |
231 |
Error occurred while setting virtual disk
as boot disk. |
232 |
Error occurred while setting name for virtual
disk. |
233 |
Couldn't get boot virtual disk. |
234 |
PCIe Link Speed could not be set for the
RAID controller. Please check if the controller has the capability
to set/change its PCIe link speed. |
235 |
PCIe Link Speed can be set to either 2
or 3 i.e. PCIe Generation 2.0 or 3.0. |
236 |
PCIe Link Speed could not be retrieved
for this RAID controller.Please check if the controller has the PCIe
link speed capability. |
237 |
Please reset the controller before doing
any further operation. |
238 |
Boot Mode can be set to 0 (BIOS stop on
error), 1 (BIOS continue on error), 2 (Headless continue on error) |
239 |
Boot Mode could not be set for the RAID
controller. |
240 |
Enable Auto Import can be set to 0 (No)
or 1 (Yes). |
241 |
Cannot discard the preserved cache because
a foreign configuration is present on the controller. Use '-ignoreconfig'
or '-igncfg' to discard the cache. |
1000 |
Enable Auto Import property could not
be set for the RAID controller. |
1001 |
Invalid array disk list. |
1002 |
Source or destination disk is in invalid
state. Make sure that the source disk is in online state, destination
disk is in ready state, and the size of the destination disk is greater
than or equal to the size of the source disk. |
1003 |
Operation not allowed. Cannot set the
array disk state to online. |
1004 |
Operation not allowed. Cannot set the array
disk state to offline. |
1005 |
Invalid encrypted array disk list for the
instant secure erase operation. |
1006 |
Sector drives 512B and 4KB must not be
combined while creating a virtual disk. |
1007 |
Hot spare sector size for the virtual disk
is not matching. |
1008 |
sectorsize parameter is not found. |
1009 |
Warning! Cannot assign global hotspare.
Input array disk can act as a hotspare only for virtual disks with
matching sector size (4KB or 512B) and supported T10 PI capability.
Use "-force" option to discard the warning. |
1010 |
Force option is invalid for this operation
on the specified controller. |
1011 |
Input values for vdiskprotectioninfo and
vdpi are 1 and 0. |
1012 |
vdiskprotectioninfo or vdpi option is not
available on the controller. |
1013 |
Input array disks or hotspares are not
PI-capable. |
1014 |
Creation of RAID 10 virtual disk with Uneven
Span failed. |
1015 |
Spanlength is not required for creating
a RAID10 virtual disk on this controller. |
1016 |
Unsupported operation. RAID 6 and RAID
60 virtual disks which are T10 PI enabled do not support Slow Initialize. |
1017 |
Operation is not supported. The specified
controller does not have encryption capability. |
1018 |
Operation is not supported. Encryption
key is not present on the specified controller. |
1019 |
The specified array disks or hotspares
do not have encryption capability. |
1020 |
The specified controller does not have
a locked foreign configuration. |
1021 |
Invalid passphrase. |
1022 |
Input values for secureflag and sf are
1 and 0. |
1023 |
Unsupported operation. Preserved cache
is not present on the controller. |
1024 |
Invalide Key Id |
1025 |
Encryption key is already set for the
controller. |
1026 |
Cannot delete the encryption key because
secure virtual disk is present. |
1027 |
The passphrase is invalid or old. |
1028 |
Cannot increase the virtual disk size
due to lack of free space or due to the presence of partial virtual
disks on the same set of array disks. |
1029 |
The percentage value of virtual disk size
must be in the range 1-100. |
1030 |
Error! Cannot discard the preserved cache.
Use '-force' option to discard the cache. |
1031 |
Cannot create a new virtual disk because
preserved cache is present on the controller. To clear the cache,
either import the related virtual disks or discard the cache. |
1032 |
Unsupported RAID value. The expand virtual
disk size operation is allowed only on RAID-0, RAID-1, RAID-5, and
RAID-6. |
1033 |
Unsupported file type. Supported file
types are .ini, .log, and .txt. |