0 |
Success |
1 |
Attempt to read write-only parameter. |
2 |
Password cannot exceed 16 characters. |
3 |
A BMC was either not detected or is not
supported. |
4 |
This username is already in use. Enter
a unique username. |
5 |
Access mode not supported. |
6 |
Cannot return number of requested data
bytes. |
7 |
User ID 1 cannot be assigned a username. |
8 |
Cannot execute duplicated request. |
9 |
There was an error clearing the SEL. |
10 |
Clear SEL cannot be accompanied with any
other option. |
11 |
racreset cannot be accompanied with any
other option. |
12 |
Cannot execute command. Command, or request
parameter(s), not supported in present state. |
13 |
Command not supported on given channel. |
14 |
The community string may only contain printable
ASCII characters. |
15 |
Destination unavailable. Cannot deliver
request to selected destination. |
16 |
Cannot execute command. Insufficient privilege
level. |
17 |
Command illegal for specified sensor or
record type. |
18 |
Invalid commstring value. |
19 |
Hardware subsystem error. Invalid data
field in Request. |
20 |
Invalid destination IP address. |
21 |
The GUID is invalid. |
22 |
Invalid gateway. |
23 |
Invalid hostname. |
24 |
Invalid IP address. |
25 |
Invalid DNS IP address. |
26 |
Invalid sub net mask. |
27 |
Invalid value for PEF. PEF value should
be between 1 and 16. |
28 |
Reservation Canceled or Invalid Reservation
ID. |
29 |
Invalid Time to live value. |
30 |
Invalid VLANID value. |
31 |
Invalid Command. Used to indicate an unrecognized
or unsupported command. |
32 |
Command invalid for given LUN. |
33 |
Load defaults cannot be accompanied with
any other option. |
34 |
There was an error loading the defaults. |
35 |
Node Busy. Command could not be processed
because command processing resources are temporarily unavailable. |
36 |
Out of space. Command could not be completed
because of a lack of storage space required to execute the given command
operation. |
37 |
This parameter is not supported. |
38 |
Parameter out of range. One or more parameters
in the data field of the Request are out of range. |
39 |
The password may only contain printable
ASCII characters. |
40 |
Password test failed. |
41 |
Requested data length invalid. |
42 |
Requested data field length limit exceeded. |
43 |
Requested Sensor, data, or record not present. |
44 |
Request data truncated. |
45 |
Command response could not be provided. |
46 |
Command response could not be provided.
BMC initialization or initialization agent in progress. |
47 |
Command response could not be provided.
Device in firmware update mode. |
48 |
Command response could not be provided.
SDR Repository in update mode. |
49 |
Cannot execute command, SEL erase in progress. |
50 |
Attempt to set the 'set in progress' value
when not in the 'set in complete' state. |
51 |
The SOL character ’accumulate interval’
is invalid. |
52 |
The SOL character ’send threshold’ is
invalid. |
53 |
The SOL ’retry interval’ is invalid. |
54 |
Command completed successfully. |
55 |
Time-out while processing command. Response
unavailable. |
56 |
Unspecified error. |
57 |
The password may only contain printable
ASCII characters. |
58 |
Username cannot exceed 16 characters. |
59 |
Invalid VLANID value. Enter in ’dddd’
format. |
60 |
Attempt to write read-only parameter. |
61 |
BMC is busy. |
62 |
Response data did not return successfully. |
63 |
BMC time out error. |
64 |
Option requires an argument. |
65 |
The asset tag for this system is not available. |
66 |
The asset tag cannot be more than 10 characters
long. |
67 |
The required BIOS interfaces cannot be
found on this system. |
68 |
The BIOS version information is not available. |
69 |
There is not enough free system memory
to complete the BIOS update. |
70 |
The BIOS update file version is a different
version class (A00, X00) than the current system BIOS. Use the --force
option to use this BIOS image. |
71 |
The BIOS update file version is older than
the current system bios. Use the --force option to use this BIOS image. |
72 |
The BIOS update file version is identical
to the current system bios. Use the --force option to use this BIOS
image. |
73 |
The sequence list must be a comma-separated
numerical list of valid unique boot device numbers (ex: 2, 1, 3). |
74 |
The sequence list must be a comma-separated
list of valid unique device names (ex: nic.emb.1, hdd.emb.1) or a
comma-separated numerical list of valid unique boot device numbers
(ex: 2, 1, 3). |
75 |
There was an error setting the sequence. |
76 |
The list is not formatted correctly. See
the help for more details. |
77 |
The size of returned buffer is larger
than the size of allocated buffer. |
78 |
There was a problem getting the state
byte. |
79 |
The state byte is not available on this
system. |
80 |
There was a problem setting the state
byte. |
81 |
The state byte must be a value between
0 and 255 decimal. |
82 |
The CPU information is not available. |
83 |
The dependent option required for this
subcommand is missing in the command line. |
84 |
Duplicate sub command has been entered. |
85 |
The script file does contain not a valid
DTK environment script signature. |
86 |
The format of the environment variable
is incorrect. |
87 |
The --envar option can only be used for
a single option. |
88 |
The --envar option can only be used for
report operations. |
89 |
The individual sub commands should be specified
for the -s option. |
90 |
Getting external serial connector settings
failed. |
91 |
Setting external serial connector settings
failed. |
92 |
There was an error opening the file. |
93 |
File does not have write permission. |
94 |
The file contains invalid options. |
95 |
The replication information does not match
for this system. |
96 |
There can only be one section in the input
file. |
97 |
Bad ini file, the section cannot be found. |
98 |
The format of the bios image file is incorrect. |
99 |
Report operations and set operations must
be separate. |
100 |
Help is not available for the option. |
101 |
The -x (--hex) option can only be used
with -b or -r. |
102 |
Input file not found. |
103 |
Input file cannot be read. |
104 |
Invalid argument for option. |
105 |
Function table lookup error. |
106 |
The machine ID was not found in the file. |
107 |
The system memory information is not available. |
108 |
Mode can only be used with the --pci option. |
109 |
The device name or index must be present
in the boot order. |
110 |
The output file could not be opened. Please
make sure the path exists and the media is not write protected. |
111 |
Could not write to output file, disk may
be full. |
112 |
The current password must be supplied
with a new password using --oldsyspwd. |
113 |
The current password must be supplied
with a new password using --oldsetuppwd. |
114 |
The current password can only be supplied
when setting a new password. |
115 |
Actions are not allowed for this filter.
Only alerts are allowed. |
116 |
There was an error getting the option. |
117 |
The option is not available or cannot
be configured through software. |
118 |
There was an error setting the option. |
119 |
The -n (--namefile) option can only be
used with - -pci. |
120 |
The password may only contain alphanumeric
characters. |
121 |
The BIOS passwords have been disabled via
jumper. |
122 |
The password length must be between 1
and 32. |
123 |
This password is locked and can only be
unlocked by the admin user. |
124 |
There was an error setting the password. |
125 |
The LCD string length must be between 1
and %s. |
126 |
The LCD string may only contain alphanumeric
characters. |
127 |
There was an error setting the LCD string. |
128 |
The second channel can only be set if
the RAID controller is set to RAID. |
129 |
The set operation requires sub commands. |
130 |
The service tag for this system is not
available. |
131 |
The system ID value is not available. |
132 |
The system information string is not available. |
133 |
A system error has occurred. |
134 |
Usage error. |
135 |
The uuid information is not present on
this system |
136 |
Version cannot be accompanied with any
other option. |
137 |
The self-identify blinker timer should
be set to 0..255 second(s). |
138 |
Encrypt key is too long. |
139 |
Encrypt key is invalid, accepted characters
are 0 to 9 or A to F. |
140 |
Parameter has been temporarily disabled
due to a dependency on other settings. |
141 |
The old password supplied is incorrect.
The new password will not be set. Please try again. |
142 |
Cannot stat /etc/omreg.cfg file. Please
ensure /etc/omreg.cfg file is present and is valid for your environment.
You can copy this file from the DTK iso. |
143 |
Getting nicselection settings failed. |
144 |
HAPI Driver Load Error. |
145 |
Filter action power reduction is only
supported for the system power warn/fail filters. |
146 |
TPM/TCM Clear settings requires setup password. |
147 |
There is currently no TPM/TCM Clear request
pending. |
148 |
Password is not required for retrieving
the ’%s’ options. |
149 |
Setup password is required for setting
the ’%s’ options. |
150 |
Invalid Password override. |
151 |
Invalid TPM/TCM set option. |
152 |
There was an error setting the TPM/TCM
option. |
153 |
There is no setup password installed on
this system. |
154 |
The setup password supplied is incorrect.
Please try again. |
155 |
Profile should be custom for setting cpupowermode,
memorypowermode and fanmode. |
156 |
There was an error setting the Power Option. |
157 |
The power cap value entered is out of
range. Please try again. |
158 |
The power cap value entered must be between
0 to 100 if unit is percent. |
159 |
Invalid IPv6 address. The IPv6 address
cannot be link-local or multicast. |
160 |
Invalid IPv6 address. The IPv6 address
specified has incorrect address format. |
161 |
Invalid IPv6 address. The gateway address
specified has incorrect address format. |
162 |
Invalid IPv6 address. The Primary DNS
server address specified has incorrect address format. |
163 |
Invalid IPv6 address. The Secondary DNS
server address specified has incorrect address format. |
164 |
Invalid IPv6 address. The gateway address
specified is invalid. |
165 |
Invalid configuration. Attempting to apply
IPv6 configuration on a non supported platform. |
166 |
Invalid IPv6 configuration. Attempt to
set DNS server address manually while DNS address source is set to
auto. |
167 |
Invalid IPv6 configuration. Attempt to
set IPv6 address manually while IPv6 address source is set to auto. |
168 |
Invalid IPv6 configuration. Attempting
to apply IPv6 configuration without loading IPv6 stack. |
169 |
Invalid IPv4 configuration. Attempting
to apply IPv4 configuration with IPv4 disabled. |
170 |
Invalid IPv6 configuration. Ipv6 address
cannot be specified without specifying prefix-length. |
171 |
Invalid IPv6 configuration. dnssrcv6 cannot
be set to auto when ipsrcv6 is set to manual. |
172 |
Error while executing IPMI Set command. |
173 |
Error while executing IPMI Get command. |
174 |
Error during Trap Alert. |
175 |
Unspecified error. |
176 |
Getting LCD settings failed. |
177 |
Invalid configuration. Attempting to set
cap when capenable is set to disable. |
178 |
Invalid configuration. Attempting to set
cap when hardware does not support setting. |
179 |
Invalid Configuration Option. |
180 |
Cannot execute command. Parameter is illegal
because command sub-function has been disabled or is unavailable. |
181 |
Failed to report the removable flash media
redundancy status. |
182 |
Failed to report the Internal SD Module
status. |
183 |
Error locating the Virtual Media Key on
the Modular system. |
184 |
Error in setting the redundancy option
for the Internal SD Modules. |
185 |
Error in retrieving the redundancy option
for the Internal SD Modules. |
186 |
Error in setting the redundancy option
on Modular systems for the Internal SD Modules. |
187 |
Error in retrieving the vFlash option. |
188 |
Error in setting the vFlash option. |
189 |
The set operation failed due to dependency. |
190 |
The set operation failed because attribute
is forced to a value. |
191 |
Cannot disable this OrderedList’s entries. |
192 |
The set operation failed because system
is busy now . Try again later. |
193 |
New value for the token not valid. |
194 |
Token not found. |
195 |
The set operation failed because System
Services and/or CSIOR disabled. |
196 |
The set operation failed due to pending
System Password changes. |
197 |
The set operation failed due to Password
verification failure. |
198 |
The set operation failed due to previously
scheduled job. |
199 |
The set operation failed because attribute
is suppressed. |
200 |
The set operation failed due to Generic
failure. |
201 |
XML path context creation failed. |
202 |
Unable to parse XML. |
203 |
Unable to connect data manager. |
204 |
'root' privileges required to execute
this application. |
205 |
Invalid alert destination. |
206 |
The set operation failed due to unspecified
error. |
207 |
Incorrect syntax for help. For more information
about a particular command, use the option '-h or --help' followed
by the command name. Example: %s -h --asset |
208 |
System is busy now.Try again later. |
209 |
The dependent option '%s' required for
this subcommand should be 'enable'. |
210 |
Some of the BIOS/IPMI tokens are ignored.
See the log file (dtk.log) for more information. |
211 |
Unsupported file name extension.Supported
file name extension is XML |
212 |
Unsupported file name extension.Supported
file name extensions are .ini, .log, .bat, .ids, .lst, and .txt. |