Skip to main content
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Enjoy members-only rewards and discounts
  • Create and access a list of your products
  • Manage your Dell EMC sites, products, and product-level contacts using Company Administration.

Dell SmartFabric OS10 User Guide Release 10.5.3

PDF

show ipv6 dhcp-relay

Displays the DHCPv6 relay information about the client interfaces.

Syntax
show ipv6 dhcp-relay interface {{ethernet node/slot/port | port-channel id-number} | vlan vlan-id [{ethernet node/slot/port | port-channel id-number}] | virtual-network vnid}
Parameters
  • ethernet node/slot/port—Enter the interface information.
  • port-channel id-number—Enter the port channel ID, from 1 to 999 or 1001 to 2000.
  • vlan vlan-id—Enter the VLAN ID number.
  • virtual-network vnid—Enter a virtual-network ID.
Defaults
None
Command Mode
EXEC
Usage Information

The show ipv6 dhcp-relay command displays the following information:

Interface name
Per-interface interface-id field value
Per-interface remote-id field value
Per-interface source-interface field value

show ipv6 dhcp relay interface <interface> - This command displays the relay information for the requested interface.

If the interface-id option is enabled, the show command displays the option-18 value which is sent in packet Format:- interface-id (or) prefix:interface-id (if prefix is configured)

If the remote-id option is enabled, the show command displays the option-37 value which is sent in packet format:- remote-id (or) prefix:remote-id (if prefix is configured)

If interface-id option is disabled, the corresponding show command field displays Disabled.

If remote-id option is disabled, the corresponding show command field displays Disabled.

If source interface is configured with IP address, the corresponding show command field displays source-interface IP address.

If the source interface is configured without any IP address, the corresponding show command field displays that the source-interface IP address is not configured.

If source interface is not configured, the corresponding show command field displays that the source-interface is not configured.

If an interface is associated to a VLAN, then it is mandatory to give both VLAN and port information in the show command. For example, show ipv6 dhcp-relay vlan 10 ethernet 1/1/1. Otherwise, the show command displays an empty output.

NOTE: If an interface is associated with a VLAN, then you must specify both the VLAN and port information in the show command. For example, show ipv6 dhcp-relay vlan 10 ethernet 1/1/1. Otherwise, the show command displays empty output.
NOTE: This command is accessible to all user roles.
Example
OS10(conf)#ipv6 dhcp-relay remote-id 
OS10(conf)#ipv6 dhcp-relay interface-id
OS10-Relay(config)# interface loopback 1
OS10-Relay(config)# interface loopback 1
OS10-Relay(conf-if-lo-1)# show configuration
!
interface loopback1
no shutdown
ipv6 address 55::1/64
OS10-Relay(conf-if-lo-1)#

OS10-Relay(conf-if-eth1/1/1)# ipv6 dhcp-relay source-interface loopback 1
Relay(config)# show ipv6 dhcp-relay interface ethernet 1/1/1
Interface : ethernet1/1/1
Interface-id[option-18] : Enabled
Interface-id value : ethernet1/1/1
Remote-id[option-37] : Enabled
Enterprise-number : 674
Remote-id value : 0003000126b6775dfb76
Source-ip : 55::1 (loopback1)
Relay(config)#

Relay(conf-if-eth1/1/1)# no ipv6 dhcp-relay source-interface  
Relay(config)# show ipv6 dhcp-relay interface ethernet 1/1/1
Interface : ethernet1/1/1
Interface-id[option-18] : Enabled
Interface-id value : ethernet1/1/1
Remote-id[option-37] : Enabled
Enterprise-number : 674
Remote-id value : 0003000126b6775dfb76
Source-ip : Not Configured
Relay(config)#
Supported Releases
10.5.2.1 or later

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\