- Notes, cautions, and warnings
- Introduction and Preparation
- Install the System in the Rack
- Install the Disk Shelves in the Rack
- Connect Cables and Power On
- Connecting the expansion shelves and the controllers
- ES30 cable information
- Connecting multiple ES30 shelves to the DD9800 system
- DS60 cable information
- Connecting multiple DS60 shelves to the DD9800 system
- Connecting the HA interconnect
- Connect data cables on both nodes
- Power on the systems
- Install the bezel
- Configure System for Use
- Add Storage Capacity
Data Domain DD9800 System Installation and Storage Expansion Guide
Verify and configure the new disks
About this task
Steps
- Run the filesys enable to command to reenable the file system.
-
Run the
enclosure show summary command to verify the Data Domain system recognizes the new disk shelf.
NOTE This step is not required when adding a new disk pack to an existing DS60.
- For a new DS60:
# enclosure show summary Enclosure Model No. Serial No. State OEM Name OEM Value Capacity --------- --------- --------------- ------ -------- --------- -------- 1 DD#### <Serial#> Online 4 Slots 2 DS60 <Serial#> Online 60 Slots 3 DS60 <Serial#> Online 60 Slots --------- --------- --------------- ------ -------- --------- -------- 3 enclosures present.
- For a new ES30:
# enclosure show summary Enclosure Model No. Serial No. State OEM Name OEM Value Capacity --------- --------- --------------- ------ -------- --------- -------- 1 DD#### <Serial#> Online 4 Slots 2 ES30 <Serial#> Online 15 Slots 3 ES30 <Serial#> Online 15 Slots --------- --------- --------------- ------ -------- --------- -------- 3 enclosures present.
- For a new DS60:
-
Run the
enclosure show topology command to verify there are two valid SAS paths to the new storage.
NOTE This step is not required when adding a new disk pack to an existing DS60.NOTE Optionally run the enclosure test topology command to test each SAS path.
-
Run the
disk show state command to verify the system can see all the disks in the new enclosure. All the new disks should display in the
Unknown state.
- For a new disk pack in an existing DS60:
# disk show state Enclosure Disk Row(disk-id) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 -------------- ---------------------------------------------- 1 . . . . 2 |--------|--------|--------|--------| | Pack 1 | Pack 2 | Pack 3 | Pack 4 | E(49-60) |. . s |U U U |- - - |- - - | D(37-48) |. . . |U U U |- - - |- - - | C(25-36) |. . . |U U U |- - - |- - - | B(13-24) |. . . |U U U |- - - |- - - | A( 1-12) |. . . |U U U |- - - |- - - | |--------|--------|--------|--------| -------------- ---------------------------------------------- Legend State Count ------ ------------------- ----- . In Use Disks 18 s Spare Disks 1 U Unknown Disks 15 - Not Installed Disks 30 ------ ------------------- ----- Total 34 disks - For a new DS60:
# disk show state Enclosure Disk Row(disk-id) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 -------------- ---------------------------------------------- 1 . . . . 2 |--------|--------|--------|--------| | Pack 1 | Pack 2 | Pack 3 | Pack 4 | E(49-60) |. . . |. . . |. . . |. . . | D(37-48) |. . . |. . . |. . . |. . . | C(25-36) |. . . |. . . |. . . |. . . | B(13-24) |. . . |. . . |. . . |. . . | A( 1-12) |. . s |. . s |. . s |. . s | |--------|--------|--------|--------| 3 |--------|--------|--------|--------| | Pack 1 | Pack 2 | Pack 3 | Pack 4 | E(49-60) |U U U |- - - |- - - |- - - | D(37-48) |U U U |- - - |- - - |- - - | C(25-36) |U U U |- - - |- - - |- - - | B(13-24) |U U U |- - - |- - - |- - - | A( 1-12) |U U U |- - - |- - - |- - - | |--------|--------|--------|--------| -------------- ---------------------------------------------- Legend State Count ------ ------------------- ----- . In Use Disks 60 U Unknown Disks 15 s Spare Disks 4 - Not Installed Disks 45 ------ ------------------- ----- Total 79 disks - For a new ES30:
# disk show state Enclosure Disk 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 --------- ------------------------------------------------- 1 s . . . 2 . . . . . . . . . . . . . . s 3 U U U U U U U U U U U U U U U --------- ------------------------------------------------- Legend State Count ------ --------------- ----- . In Use Disks 17 s Spare Disks 2 U Unknown Disks 15 ------ --------------- ----- Total 34 disks
- For a new disk pack in an existing DS60:
-
Run the
storage add tier
<storage-tier> enclosure
<enclosure-number> command to add the new enclosure to the Data Domain system volume. The command prompts for confirmation, and requires the sysadmin password to complete. Run the command once for each enclosure being added.
- To add a new disk pack (DS60) to Active Tier storage:
# storage add tier active enclosure 2:2 Checking storage requirements...done Adding enclosure 2:2 to the active tier...Enclosure 2:2 successfully added to the active tier. Updating system information...done Successfully added: 2:2 done
- To add a new disk pack (DS60) to Archive Tier storage:
# storage add tier archive enclosure 2:2 Checking storage requirements...done Adding enclosure 2:2 to the archive tier...Enclosure 2:2 successfully added to the archive tier. Updating system information...done Successfully added: 2:2 done
- To add a new disk pack (DS60) to Cloud Tier storage:
# storage add tier cloud enclosure 2:2 Checking storage requirements...done Adding enclosure 2:2 to the cloud tier...Enclosure 2:2 successfully added to the cloud tier. Updating system information...done Successfully added: 2:2 done
- To add a new shelf to Active Tier storage:
# storage add tier active enclosure 3 Checking storage requirements...done Adding enclosure 3 to the active tier...Enclosure 3 successfully added to the active tier. Updating system information...done Successfully added: 3 done
- To add a new shelf to Archive Tier storage:
# storage add tier archive enclosure 3 Checking storage requirements...done Adding enclosure 3 to the archive tier...Enclosure 3 successfully added to the archive tier. Updating system information...done Successfully added: 3 done
- To add a new shelf to Cloud Tier storage:
# storage add tier cloud enclosure 3 Checking storage requirements...done Adding enclosure 3 to the cloud tier...Enclosure 3 successfully added to the cloud tier. Updating system information...done Successfully added: 3 done
- To add a new disk pack (DS60) to Active Tier storage:
-
Run the
disk show state command to verify the system can see all the disks in the new enclosure. All the new disks should display in the
Available state.
- For a new disk pack in an existing DS60:
# disk show state Enclosure Disk Row(disk-id) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 -------------- ---------------------------------------------- 1 . . . . 2 |--------|--------|--------|--------| | Pack 1 | Pack 2 | Pack 3 | Pack 4 | E(49-60) |. . s |v v v |- - - |- - - | D(37-48) |. . . |v v v |- - - |- - - | C(25-36) |. . . |v v v |- - - |- - - | B(13-24) |. . . |v v v |- - - |- - - | A( 1-12) |. . . |v v v |- - - |- - - | |--------|--------|--------|--------| -------------- ---------------------------------------------- Legend State Count ------ ------------------- ----- . In Use Disks 18 s Spare Disks 1 v Available Disks 15 - Not Installed Disks 30 ------ ------------------- ----- Total 34 disks - For a new DS60:
# disk show state Enclosure Disk Row(disk-id) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 -------------- ---------------------------------------------- 1 . . . . 2 |--------|--------|--------|--------| | Pack 1 | Pack 2 | Pack 3 | Pack 4 | E(49-60) |. . . |. . . |. . . |. . . | D(37-48) |. . . |. . . |. . . |. . . | C(25-36) |. . . |. . . |. . . |. . . | B(13-24) |. . . |. . . |. . . |. . . | A( 1-12) |. . s |. . s |. . s |. . s | |--------|--------|--------|--------| 3 |--------|--------|--------|--------| | Pack 1 | Pack 2 | Pack 3 | Pack 4 | E(49-60) |v v v |- - - |- - - |- - - | D(37-48) |v v v |- - - |- - - |- - - | C(25-36) |v v v |- - - |- - - |- - - | B(13-24) |v v v |- - - |- - - |- - - | A( 1-12) |v v v |- - - |- - - |- - - | |--------|--------|--------|--------| -------------- ---------------------------------------------- Legend State Count ------ ------------------- ----- . In Use Disks 60 v Available Disks 15 s Spare Disks 4 - Not Installed Disks 45 ------ ------------------- ----- Total 79 disks - For a new ES30:
# disk show state Enclosure Disk 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 --------- ------------------------------------------------- 1 s . . . 2 . . . . . . . . . . . . . . s 3 v v v v v v v v v v v v v v v --------- ------------------------------------------------- Legend State Count ------ --------------- ----- . In Use Disks 17 s Spare Disks 2 v Available Disks 15 ------ --------------- ----- Total 34 disks
- For a new disk pack in an existing DS60:
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\