- Notes, cautions, and warnings
- Preface
- Introduction
- Installation
- Preparing to install the Avamar Plug-in for Oracle
- Installing, upgrading, and uninstalling the software on HP-UX
- Installing, upgrading, and uninstalling the software on IBM AIX
- Installing, upgrading, and uninstalling the software on Linux
- Installing, upgrading, and uninstalling the software on Solaris
- Installing, upgrading, and uninstalling the software on Windows
- Excluding Oracle directories from file system backups
- Oracle RAC Configuration
- High Availability Oracle Single-Instance Database Configuration
- Backup
- Restore and Recovery
- Backup and Restore with Oracle RMAN
- Preparing the system for RMAN backups and restores
- Specifying RMAN parameters to improve performance
- Backing up Oracle data with RMAN
- Restoring Oracle data with RMAN
- Supporting netbind flag in avoracle
- Using advanced restore commands
- Managing backup retention
- Allocating multiple channels
- Managing RMAN backups and restores through Avamar Administrator
- Plug-in Options
- Troubleshooting
- Backup and restore problems and solutions
- Avamar Administrator shows a completed RMAN backup or restore as still running
- avoracle Error <7936>: No valid targets found
- Activity monitor of RMAN backup shows an incorrect status of still running.
- Backups fail when backup copies is set to more than 1
- Log files for RMAN operations cannot be viewed from the Avamar Administrator if a custom var directory is used.
- Backups unavailable after registering secondary RAC node
- Cannot open file f_cache.dat error
- Cannot Sync error
- Failed RMAN restore of control file is reported as completed in Avamar Administrator
- Hot backup fails with Oracle not available error
- Level-1 backup of a large database fails with a snapview timeout
- ORA-19870: error while restoring backup piece
- ORA-25153: Temporary Tablespace is Empty
- ORA-27211: Failed to load Media Management Library
- Restore fails to complete successfully
- RMAN backup script fails with media management errors
- RMAN backup script fails with ORA-19511
- RMAN-06056: could not access datafile n error on AIX
- RMAN script fails with WriteFile failed error
- Time-out errors when using multiple RMAN channels
- Unable to process snapview workorder
- Unable to send CTL message
- The no_of_channels parameter no longer supported
- Hidden backups
- Configuration problems and solutions
- Avamar client and Avamar Plug-in for Oracle registration
- Bitwidth of Avamar Plug-in for Oracle and Oracle
- Cluster Configuration Tool fails to start
- Determining the version of Oracle
- Disk space for the /var/avamar directory
- Oracle RAC database failover
- Requirements for libobk_avamar.so and libobk_avamar.dll
- RMAN executable file and Oracle versions
- Stopping Avamar Administrator processes
- Unable to browse Oracle databases with Avamar Administrator
- Verifying the client and plug-in versions
- Backup and restore problems and solutions
- Glossary
Dell Avamar for Oracle 19.10 User Guide
VCS configurations
The Avamar Plug-in for Oracle supports both two-node active/active and two-node active/passive VCS configurations. You can use the Avamar Plug-in for Oracle to back up Oracle database files from Solaris platforms that run VCS.
In an active/active cluster configuration, each node runs an instance of the Avamar Plug-in for Oracle as an application in separate service groups. This functionality provides application redundancy. When a failure occurs on one active node, the other active node hosts both service groups.
In an active/passive cluster configuration, the service group is online on the active node until a failover occurs. Then the service group comes online on the passive node.
You can run backups and restores from both nodes.
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\