Displays only VMFS datastores that are not part of a consistency group.
-type
Identifies the type of resources to display. Valid values are (case insensitive):
primary
tc
-baseRes
(Applies to thin clones only) ID of the base VMFS datastore by which to filter thin clones.
-baseResName
(Applies to thin clones only) Name of the base VMFS datastore by which to filter thin clones.
-originalParent
(Applies to thin clones only) ID of the parent VMFS datastore by which to filter thin clones.
-originalParentName
(Applies to thin clones only) Name of the parent VMFS datastore by which to filter thin clones.
-source
(Applies to thin clones only) ID of the source snapshot by which to filter thin clones.
-sourceName
(Applies to thin clones only) Name of the source snapshot by which to filter thin clones.
Example 1
The following command displays details about VMFS datastores and their thin clones :
uemcli -d 10.0.0.1 -u Local/joe -p MyPassword456! /stor/prov/vmware/vmfs show -detail
Storage system address: 10.0.0.1
Storage system port: 443
HTTPS connection
1: ID = res_6
LUN = sv_25
Name = VMFS Datastore 1
Description =
Type = Primary
Base storage resource = res_6
Source =
Original parent =
Health state = OK (5)
Health details = "The component is operating normally. No action is required."
Storage pool ID = pool_1
Storage pool = Pool 1
Size = 1099511627776 (1.0T)
Maximum size = 70368744177664 (64.0T)
Thin provisioning enabled = yes
Data Reduction enabled = yes
Data Reduction space saved = 267361714176 (249.0G)
Data Reduction percent = 57%
Data Reduction ratio = 2.3:1
Advanced deduplication enabled = no
Current allocation = 172823429120 (160.9G)
Preallocated = 82576048128 (76.9G)
Total Pool Space Used = 203844583424 (189.8G)
Protection size used = 20820606976 (19.3G)
Non-base size used = 20820606976 (19.3G)
Family size used = 203844583424 (189.8G)
Snapshot count = 2
Family snapshot count = 2
Family thin clone count = 0
Protection schedule = snapSch_1
Protection schedule paused = no
SP owner = SPB
Trespassed = no
Version = 5
Block size = 1
Virtual disk access hosts = Host_2
Host LUN IDs = 12
Snapshots access hosts =
WWN = 60:06:01:60:09:00:43:00:CB:38:88:5B:BB:10:5B:09
Replication destination = no
Creation time = 2018-08-30 18:34:46
Last modified time = 2018-08-30 18:34:46
IO limit =
Effective maximum IOPS = N/A
Effective maximum KBPS = N/A
Example 2
The following command displays details about the thin clones derived from the LUN named sv_2:
Storage system address: 10.0.0.1
Storage system port: 443
HTTPS connection
ID = vmware_2
LUN = sv_2
Name = MyFC
Description = My description
Type = Thin clone
Base storage resource = vmware_1
Source = snap_1
Original parent = vmware_1
Health state = OK (5)
Storage pool ID = pool_2
Storage pool = capacity
Size = 107374182400 (100G)
Protection size used =
Non-base size used = 0
SP owner = SPA
Trespassed = no
Data is not available for the Topic
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\