Integrated Devices |
--EmbNicPort
nBootProto
|
Unknown, None, Pxe, Iscsi
|
Controls the legacy boot protocol of the LOM port specified
by the embedded NIC port number. This is a write-only attribute. This
attribute is for systems management software use, and does not appear
in system BIOS setup. This attribute always returns Unknown, when
read. There is no change to the LOM port legacy boot protocol setting
when Unknown is returned. An error is returned if written with a setting
(
None, PXE, or iSCSI) that is not supported by the
LOM Port.
|
|
--EmbVideo
|
Enabled, Disabled
|
Enables or disables the BIOS support for the Embedded Video
Controller.
|
|
--IntegratedNetwork1
|
Enabled, DisabledOs,
|
Enables or disables Integrated Network 1.
-
NOTE: If set to
DisabledOs, the Integrated NICs may still be available for shared network access
by the embedded management controller. This function must be configured
through the NIC management utilities provided with your system.
|
|
--IntegratedNetwork2
|
Enabled, DisabledOs
|
Enables or disables Integrated Network 2.
-
NOTE: If set to
DisabledOs, the Integrated NICs may still be available for shared network access
by the embedded management controller. This function must be configured
through the NIC management utilities provided with your system.
|
|
--IntegratedRaid
|
Enabled, Disabled
|
Enables or disables the integrated RAID controller. |
|
--IntegratedSas
|
Enabled, Disabled
|
Enables or disables the integrated SAS controller. |
|
--InternalSdCard
|
On, Off
|
Turns the internal SD card port on or off. |
|
--InternalSdCardRedundancy
|
Mirror, Disabled
|
Sets the internal SD card port redundancy to
Mirror mode or
Disabled.
When set to
Mirror mode, read-write operation occurs on both the secure digital (SD)
cards. When one of the SD cards fails and is replaced, on booting,
the data of the active card is copied to the offline card.
When
set to
Disabled, read-write operation occurs only
on SD card 1.
-
NOTE: On Blade systems, disable the vflash key to configure this option.
This option is applicable only on PowerEdge R810, R815, R910, M910,
and PowerEdge 12G systems.
|
|
--InternalUsb
|
On, Off
|
Turns the internal USB port on or off. |
|
--InternalUsb1
|
On, Off
|
Turns the internal USB port 1 on or off. |
|
--InternalUsb2
|
On, Off
|
Turns the internal USB port 2 on or off. |
|
--IoatEngine
|
Enabled, Disabled
|
Enables or disables the I/O Acceleration Technology (I/OAT)
option.
|
|
--OsWatchdogTimer
|
Enabled, Disabled
|
Aids in the recovery of the operating system when the system
does not respond. When set to
Enabled, the operating
system is allowed to initialize the timer. When it is set to
Disabled (default value), the timer has no effect on the
system.
|
|
--SriovGlobalEnable
|
Enabled, Disabled
|
Enables or disables support for Single Root I/O Virtualization
(SR-IOV) devices.
-
NOTE: This option is supported on PowerEdge R410, R510, R610, R710, R910,
T410, T610, T710, and PowerEdge 12G systems with Intel Xeon processor
7500/6500 series.
|
|
--UsbPorts
|
AllOn, OnlyBackPortsOn, AllOff
|
Sets the user accessible USB Ports. Selecting
OnlyBackPortsOn disables front USB ports, and selecting
AllOff disables
both front and back USB ports.
|