Description
This command defines the attributes for the RAID controller
modules.
Syntax
set controller [(0 | 1)]
[availability=(online | offline | serviceMode)]
[ethernetPort [(0 | 1)]
ethernetPortOptions]
[globalNVSRAMByte [
nvsramOffset]=(
nvsramByteSetting |
nvsramBitSetting)]
[hostNVSRAMByte [
hostType,
nvsramOffset]=(
nvsramByteSetting |
nvsramBitSetting)]
[IPv4GatewayIP=
ipAddress]
[IPv6RouterAddress=
ipv6Address]
[iscsiHostPort [(0 | 1 | 2 | 3)]
iscsiHostPortOptions]
[rloginEnabled=(TRUE | FALSE)]
[serviceAllowedIndicator=(on | off)]
Parameters
Parameter
|
Description
|
controller
|
The RAID controller module for which you want to
define properties. Valid RAID controller module identifiers are
0
or
1
, where
0
is the RAID controller module in the top slot, and
1
is the RAID controller module in the bottom
slot. Enclose the identifier for the RAID controller module in square
brackets ([ ]). If you do not specify a RAID controller module, the
firmware for the RAID controller returns a syntax error.
|
availability
|
The mode for the RAID controller module, which you
can set to
online,
offline, or
serviceMode (service).
|
ethernetPort
|
The attributes (options) for the management Ethernet
ports. The entries to support this parameter are listed in the Syntax
Element Statement Data table that follows. Many settings are possible,
including setting the IP address, the gateway address, and the subnet
mask address.
|
globalNVSRAMByte
|
A portion of the RAID controller module NVSRAM. Specify
the region to be modified using the starting byte offset within the
region and the byte value or bit value of the new data to be stored
into the NVSRAM.
|
hostNVSRAMByte
|
The NVSRAM for the host-specific region. The setting
specifies the host index for the specific host, the starting offset
within the region, the number of bytes, and the byte value or bit
value of the new data to be stored into the NVSRAM.
|
IPv4GatewayIP
|
The IP address of the node that provides the interface
to the network. The address format for the IPv4 gateway is
(0–255).(0–255).(0–255).(0–255)
|
IPv6RouterAddress
|
The IP address of IPv6 router that connects two or
more logical subnets. The address format for the IPv6 router is
(0–FFFF):(0–FFFF):(0–FFFF):(0–FFFF): (0–FFFF):(0–FFFF):(0–FFFF):(0–FFFF)
.
|
iscsiHostPort
|
This parameter enables you to set options for the
iSCSI ports on the RAID controller module. Select the specific iSCSI
port and then select the options for that port. The iSCSI port identifier
can be
0
,
1
or
2
,
3
. Refer to the information
about your RAID controller module for the location and identifier
of the ports.
The values that support this parameter
are listed in the Syntax Element Statement Data table that follows.
Many settings are possible, including setting the IP address, the
gateway address, the subnet mask address, the IPv4 priority, and the
IPv6 priority.
|
rloginEnabled
|
The setting for whether the remote login feature is
turned on or turned off. To turn on the remote login feature, set
this parameter to
TRUE
. To turn off the remote
login feature, set this parameter to
FALSE
.
|
serviceAllowedIndicator
|
The setting for whether the Service Action Allowed
indicator light is turned on or turned off. To turn on the Service
Action Allowed indicator light, set this parameter to
on
. To turn off the Service Action Allowed indicator light, set
this parameter to
off
.
|
Syntax
Element Statement Data
Options for the
Ethernet Port Parameter
|
enableIPv4=(TRUE | FALSE) |
enableIPv6=(TRUE | FALSE) |
IPv6LocalAddress=(0-FFFF):(0-FFFF):(0-FFFF):(0-FFFF): (0-FFFF):(0-FFFF):(0-FFFF):(0-FFFF) |
IPv6RoutableAddress=(0-FFFF):(0-FFFF):(0-FFFF):(0-FFFF): (0-FFFF):(0-FFFF):(0-FFFF):(0-FFFF) |
IPv4Address=(0-255).(0-255).(0-255).(0-255) |
IPv4ConfigurationMethod=[(static | dhcp)] |
IPv4SubnetMask=(0-255).(0-255).(0-255).(0-255) |
duplexMode=(TRUE | FALSE) |
portSpeed=[(autoNegotiate | 10 | 100 | 1000)]
|
Options for the
iscsiHostPort Parameter
|
IPv4Address=(0-255).(0-255).(0-255).(0-255) |
IPv6LocalAddress=(0-FFFF):(0-FFFF):(0-FFFF):(0-FFFF): (0-FFFF):(0-FFFF):(0-FFFF):(0-FFFF) |
IPv6RoutableAddress=(0-FFFF):(0-FFFF):(0-FFFF):(0-FFFF): (0-FFFF):(0-FFFF):(0-FFFF):(0-FFFF) |
IPv6RouterAddress=(0-FFFF):(0-FFFF):(0-FFFF):(0-FFFF): (0-FFFF):(0-FFFF):(0-FFFF):(0-FFFF) |
enableIPv4=(TRUE | FALSE) |
enableIPv6=(TRUE | FALSE) |
enableIPv4Vlan=(TRUE | FALSE) |
enableIPv6Vlan=(TRUE | FALSE) |
enableIPv4Priority=(TRUE | FALSE) |
enableIPv6Priority=(TRUE | FALSE) |
IPv4ConfigurationMethod=(static | dhcp) |
IPv6ConfigurationMethod=(static | auto) |
IPv4GatewayIP=(TRUE | FALSE) |
IPv6HopLimit=[0-255] |
IPv6NdDetectDuplicateAddress=[0-256] |
IPv6NdReachableTime=[0-65535] |
IPv6NdRetransmitTime=[0-65535] |
IPv6NdTimeOut=[0-65535] |
IPv4Priority=[0-7] |
IPv6Priority=[0-7] |
IPv4SubnetMask=(0-255).(0-255).(0-255).(0-255) |
IPv4VlanId=[1-4094] |
IPv6VlanId=[1-4094] |
maxFramePayload=[frameSize] |
tcpListeningPort=[3260, 49152-65536] |
portSpeed=[(autoNegotiate | 1 | 10)]
|
Notes
When you use this command, you can specify one or
more parameters. You need not to use all the parameters.
Setting the availability parameter to
serviceMode causes the alternate RAID controller module to take ownership of
all of the virtual disks. The specified RAID controller module no
longer has any virtual disks and refuses to take ownership of any
more virtual disks. Service mode is persistent across reset cycles
and power cycles until the availability parameter is set to
online.
Use the
show controller
NVSRAM
command to show the NVSRAM information. Before making
any changes to the NVSRAM, contact your Technical Support Representative
to learn what regions of the NVSRAM you can modify.
When the
duplexMode option is set to
TRUE, the selected Ethernet port is set to full duplex. The default value
is half duplex (the
duplexMode parameter is set to
FALSE).
To make sure that the IPv4 settings
or the IPv6 settings are applied, you must set these
iscsiHostPort options:
-
enableIPV4=TRUE
-
enableIPV6=TRUE
The IPv6 address space is 128 bits. It is represented by eight
16-bit hexadecimal blocks separated by colons.
The
maxFramePayload option is shared between IPv4
and IPv6. The payload portion of a standard Ethernet frame is set
to
1500, and a jumbo Ethernet frame is set to
9000. When using jumbo frames, all of the devices that are
in the network path should be capable of handling the larger frame
size.
The
portSpeed option is expressed
as megabits per second (Mb/s).
Values for the
portSpeed option of the iscsiHostPort parameter are in megabits
per second (Mb/s).
The following values are the
default values for the
iscsiHostOptions
:
- The
IPv6HopLimit option is 64.
- The
IPv6NdReachableTime option is
30000 milliseconds.
- The
IPv6NdRetransmitTime option is
1000 milliseconds.
- The
IPv6NdTimeOut option is 30000 milliseconds.
- The
tcpListeningPort option is 3260.