Skip to main content
Sign Out

Welcome to Dell

My Account
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Create and access a list of your products
Sign In Create an Account Premier Sign In Partner Program Sign In
Contact Us

Your Dell.com Carts

Dell SmartFabric OS10 User Guide Release 10.5.4

PDF

show vlt mismatch

Displays information that enables an administrator to identify configuration mismatches corresponding to the Layer3 multicast commands on the VLT nodes.

Syntax
show vlt vlt-id mismatch [pim]
Parameters
  • vlt [vlt-id]—Enter the VLT domain ID.
  • [pim]—Displays PIM mismatch in VLT peers.
Default
None
Command Mode
EXEC
Usage Information
You can use this command to identify the configuration mismatches corresponding to the following Layer 3 multicast commands on the VLT nodes:
  • Presence of global IPv6 multicast-routing enable or disable configuration.
  • Presence of PIM sparse mode per interface level enable or disable configuration.
  • Presence of PIM SSM range configuration.
  • Presence of PIM join, neighbor, and register filter configurations.
  • Presence of anycast RP configuration.
Example 
OS10# show vlt 1 mismatch
VLT-MAC mismatch:
No mismatch

Peer-routing mismatch:
No mismatch

VLAN mismatch:
No mismatch

VLT VLAN mismatch:
No mismatch

VLT Virtual Network Mismatch:
Virtual Network Name Mismatch:
No mismatch

Virtual Network VLTi-VLAN Mismatch:
No mismatch

Virtual Network Mode Mismatch:
No mismatch

Virtual Network Tagged Interfaces Mismatch:
No mismatch

Virtual Network Untagged Interfaces Mismatch:
No mismatch

Virtual Network VNI Mismatch:
No mismatch

Virtual Network Remote-VTEP Mismatch:
No mismatch

Virtual Network anycast ip Mismatch:
No mismatch

Virtual Network anycast mac Mismatch:
No mismatch

EVPN Mismatch:
EVPN Mode Mismatch:
No mismatch

EVPN EVI Mismatch:
No mismatch

EVPN VRF Mismatch:
No mismatch


NVE Mismatch:
No mismatch

DHCP Snooping Mismatch:

Global Snooping Configuration Mismatch
-----------------------------------------------------
Codes: SE - Static Entry Mismatch
DT - DAI Trust Mismatch
ST - Snooping Trust Mismatch
SAV - Source-Address-Validation Mismatch
ARP - ARP Inspection Mismatch
VS - VLAN Snooping Mismatch
Interface Interface Snooping Configuration Mismatch
-----------------------------------------------------
Multicast routing mismatches:
Global status:
Parameter VRF Local Peer
-----------------------------------------------------
No mismatch

Vlan status IPv4 IPv6
VlanId Local Peer Local Peer
-----------------------------------------------------
No mismatch

PIM Anycast RP information mismatches:
Anycast RP:
Parameter       VRF        Local         Peer
-----------------------------------------------------
RP-Address   default    3:3:3::3         -

Anycast RP-Set:
RP-address      VRF         Local          Peer
-----------------------------------------------------
 4:4:4::4        default      1:1:1::1     -
                              3:3:3::3     -
                              -            2:2:2::2
Supported Releases
10.5.4.0 or later

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\