Skip to main content
Sign Out

Welcome to Dell

My Account
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Create and access a list of your products
  • Manage your Dell EMC sites, products, and product-level contacts using Company Administration.
Sign In Create an Account Premier Sign In Partner Program Sign In
Contact Us

Your Dell.com Carts

Dell SmartFabric OS10 User Guide Release 10.5.4

PDF

lacp individual

Enables or disables the LACP individual feature.

Syntax
[no] lacp individual
Parameters
None.
Default
Disabled
Command Mode
PORT-CHANNEL INTERFACE CONFIGURATION MODE
Security and access
sysadmin or secadmini with any privilege level.
Usage Information

Use this command is used to enable or disable the LACP individual feature on the port channel. The LACP Individual feature operates only on LACP port channels. On a static port channel, enabling or disabling this feature has no impact. The LACP Individual and LACP fallback features are mutually exclusive. The LACP individual and no switchport configurations are mutually exclusive.

The LACP fallback and LACP individual features cannot co-exist on the same interface.

Example 
OS10(config)# interface port-channel 100

OS10(conf-if-po-100)# lacp Individual 

<165>1 2020-11-25T09:19:26.722956+00:00 OS10 dn_alm 984 - - Node.1-Unit.1:PRI [event], Dell EMC (OS10) %LACP_INDIVIDUAL: 
Warning ! Enable LACP Individual feature only on port-channel with edge ports. Enabling this on network port-channel could lead 
to loops : port-channel100
If you enable the LACP fallback feature on an interface, you cannot configure the the LACP individual feature on the same interface, as both these features are mutually exclusive. If you try to enable LACP individual feature on an interface on which LACP fallback is already configured, the following error message is displays: 
OS10(conf-if-po-100)# show configuration
!
interface port-channel100
no shutdown
switchport access vlan 1
lacp max-bundle 20
lacp fallback enable
OS10(conf-if-po-100)# lacp individual
% Error: Interface port-channel100, LACP Fallback and LACP Individual features cannot co-exist on same interface.
If you try to configure LACP fallback on an interface that is already configured with the LACP individual feature, the following message is displays: 
OS10(conf-if-po-100)# show configuration
!
interface port-channel100
no shutdown
switchport access vlan 1
lacp individual
OS10(conf-if-po-100)# lacp fallback enable
% Error: Interface port-channel100, LACP Individual config is supported only on L2 modes.
You cannot configure LACP fallback and no switch configurations on an interface simultaneously. If you try to configure no switch on an interface that is already configured with LACP fallback, the following error message is displays. 
OS10(conf-if-po-100)# show configuration
!
interface port-channel100
no shutdown
switchport access vlan 1
lacp individual
OS10(conf-if-po-100)# no switchport
% Error: Interface port-channel100, LACP Fallback and LACP Individual features cannot co-exist on same interface.
Similarly, if you try to configure LCAP fallback on an interface that is already configured with no switch configuration, the following error message is displays: 
OS10(conf-if-po-100)# show configuration
!
interface port-channel100
no shutdown
no switchport
lacp max-bundle 20

OS10(conf-if-po-100)# lacp individual
% Error: Interface port-channel100, LACP Individual config is supported only on L2 modes.
Supported Releases
10.5.3 or later

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\